07376369067 www.williamsmo... Support the channel: www.paypal.com...
Пікірлер: 229
@johnbrown9773 Жыл бұрын
Incredible !! Top mechanic, it's hard to do in a garage but on a drive WOW !! Well done love the videos m8
@simonchesterman11083 ай бұрын
I followed your guide to change my clutch and it made the job very smooth and straightforward. Thank You !
@saadbrowny84383 жыл бұрын
just found this channel,you my friend have some serious skills and patience!i'm a machanic too and i know how difficult these jobs are even in the workshop with a lift ecc especially on these french cars so i can only imagine how hard this is soo keep it up much respect to you!
@WMCS3 жыл бұрын
Thanks for a great feedback. Especially coming from a mechanic. Much appreciated.
@rachelcarroll59512 жыл бұрын
Hi Kevin question for you if your doing clutch and ball joint or cv boot needs replacement do you change them or carry on with clutch
@ShaneyBCM3 жыл бұрын
I done the clutch and flywheel on mine a couple of months back, id read there was room to pull the box into the arch but didn't trust it so dropped the whole subframe instead, you made that look easy, good effort.
@WMCS3 жыл бұрын
That’s great you managed to do it all the way. How did you get on.
@ShaneyBCM3 жыл бұрын
@@WMCS yeah not to bad but was far from easy, couldn't find any info like this video online, managed to get use of a friends workshop with a ramp, took 3 nights to do and had to order a new clutch fork and swival ball cos they where worn through 170000miles on it. done the gearbox shaft seals and rear crank oil seal while i was in there as well. Parts aint cheap for these vans.
@alessandrer36163 жыл бұрын
The best mechanic in UK ! Thanks for sharing ! Respect Kevin !
@alessandrer36163 жыл бұрын
Two bad CV joint and bad lower ball joint.
@adishulman70043 жыл бұрын
you helped me do a gearbox change alone by my self in my drive way. good luck mate!
@WMCS3 жыл бұрын
Glad the video came in handy. Thanks for the support
@cleanikcarcenter1328 Жыл бұрын
1 ere vidéo que je vois autant d explications, sans parole le tout dans le détails ! Vraiment respect, bravo et MERCI
@jn37503 жыл бұрын
The more I watch the more I admire your skills man
@murugank.murugan69893 жыл бұрын
Iam mechanic in india .iam roll model you.very fantastic work
@WMCS3 жыл бұрын
Glad the video is coming in handy for you. Stay tuned.
@ouijem Жыл бұрын
A vrai dire c'est même rare de voir autant de précision à tous les niveau sur les tutorats KZbin... Encore Bravo du Finistère/Bretagne
@paulSmith-yg9fs3 жыл бұрын
Another Great job mate. Its time for the compilation video though, Kevin`s Greatest lift`s. Seeing you making it look easy lifting them gearboxes is everyones favourite part
@WMCS3 жыл бұрын
Paul I’m not too great with computers ., but hopefully you can do something for us 🍻✨
@caraudiosolutions3 жыл бұрын
Fantastic job Kevin Can I ask how long on average it takes to do a clutch? What car was the easiest to do?
@marinkhan30663 жыл бұрын
Generally speaking nowadays no cars are easy to work on , but personally I prefer to work on VW family cars that's like seat Skoda Audi they r design systemically which mean no hidden surprises and general it will take me around three hours to replace a clutch on them
@caraudiosolutions3 жыл бұрын
@@marinkhan3066 O ok..
@DarrenBoss19843 жыл бұрын
Good job mate! That van is gonna need some new CV joins soon. Looks like the boot has come away completely on one side and flung grease everywhere! :D
@WMCS3 жыл бұрын
Yeh both side came off. Customers are always made aware of any extra work needed. Thanks for the feedback 🍻
@johnkinnane5473 жыл бұрын
G'day well that was a bloody good job and outside in the cold and on you back, I can't get over how much you have to take off just to get to the bell housing! Thanks for filming this regards John’s
@WMCS3 жыл бұрын
John it’s a Labour of love. Otherwise it’s hard 🍻🍻
@johnkinnane5473 жыл бұрын
I reckon that it must be you have it well sorted out wit
@russjam1213 жыл бұрын
If i was that customer i would have gone out and grabbed a couple of cv axles and got them swapped out during reassembly as it saves extra labour costs
@franciscorodriguez4202 жыл бұрын
From Guadalajara México Congratulation good film Is clear and fantástic job. Amigo y colega Beto Williams Felicidades. Mi first teacher Jhon Derek Berry from England Saludos donde quiera que estén!!
@josea22863 жыл бұрын
Increíble. Buen trabajo. Lo único es que estaría bien ver cómo se vuelve a llenar de aceite la caja de cambios. Seguiré viendo tus vídeos. Saludos desde España.
@WMCS3 жыл бұрын
Saludos 🍻
@colinbell46155 ай бұрын
Hard working skillfull individual. In situ repairs separate men and boys.
@russellrrenshaw17303 жыл бұрын
Tip get a jack under the disk flange to support it when knocking out bottom ball joint ;-)
@WMCS3 жыл бұрын
Thanks .,, appreciate it.
@deancurtis9953 жыл бұрын
Now that’s a genius idea , those diesel heaters are awesome mind 👌🏻😎 another top job dude happy new year fella keep safe
@WMCS3 жыл бұрын
Dean that heater is a heaven sent.
@deancurtis9953 жыл бұрын
@@WMCS I’ve got the smaller version in my camper and tbf for the size of it don’t half kick the heat out , I bet it’s god send in these colder months even if just takes the chill out the air lol 😂
@WMCS3 жыл бұрын
I always aim it at the gearbox. Then that metal is always warm. No cold hands anymore. The little joys of life hehy 😁🍻🍻
@VintageOutboardMan3 жыл бұрын
I really enjoy your videos sir! I find your work ethic very inspiring! I have a question for you, since you have seen a lot of clutches, do you have a favorite brand of clutches?
@rockinnathan3 жыл бұрын
Just done my relay after watching these. Can safely say ill be sticking to my classic cars and hot rods. Damn French motors
@ميكانيكمحترف3 жыл бұрын
Mécanique 👍❤️
@ouijem Жыл бұрын
Merci beaucoup, très bien filmé en clair, précis et efficace... Bravo
@GerdeGroot-s2r5 ай бұрын
Amazing skills and great videos. I have a van like this one. Could you please confirm the gearbox oil capacity? I will soon have to replace the clutch but im not sure how much oil goes in. 4:30 Thanks and keep the videos up!
@ivandrago12673 жыл бұрын
Wow !! Welcome back !
@impossible10352 жыл бұрын
Complimenti per il tuo lavoro sei in gamba, grazie di condividere i tuo video.
@jamesleagas585711 ай бұрын
Can I ask roughly what the price is to supply and fit a new clutch to a 2015 2.0hdi expert? I think mines due and want someone I can trust to do it! Seems your the man for the job
@WMCS11 ай бұрын
www.williamsmobileclutch.co.uk
@lorenzo3cx3 жыл бұрын
Respect bro .. from algeria🇩🇿
@WMCS3 жыл бұрын
Thank you.
@LettingHellLooseGaming8 ай бұрын
Those waterproofs look good, could you say where they from?
@johnsands1463 жыл бұрын
Hiya Kevin, thanks for taking the time to record your work. I'm about to do the clutch on my old 03 expert with 125k miles and one owner from new so it's worth doing. Someone mentioned above about the DMF and I'm curious too. Was that converted earlier to a solid flywheel or is that how the later ones come? Reason I ask is I have a solid flywheel and clutch that's done 7k that I took out of my old van that I scrapped. Was gonna bite the bullet and replace with new clutch and DMF but think maybe I'm being too fussy and should just put the nearly new clutch and flywheel in and have done with it. It worked fine in my old van just not quite as silky but hardly noticeable. Your thoughts and knowledge much appreciated. Regards John.
@WMCS3 жыл бұрын
These engines doesn’t come with DMF., The springs are built into the clutch. A very good design. And the clutch is heavy duty.
@johnsands1463 жыл бұрын
@@WMCS Thanks very much Kevin it's good of you to take the time to reply. Stay safe fella.
@CC-qw5ps3 ай бұрын
Bonjour super vidéo à chaque fois je suis bluffé 👍👍 la boîte de vitesse de ce expert si c’est un 2l hdi vous la retrouvez sur quel véhicule ? Merci à vous
@Kaspergrovenielsen3 жыл бұрын
Wonderful video. I have just changed the clutch in my garage with your video as a help! One question. How do I restore the hydralic pressure in the pedal? I didn't see that in the video :)
@maxthecaddy84513 жыл бұрын
that bottom ball joint didn't want come off easy, good vid big thumb's up buddy👍👍
@WMCS3 жыл бұрын
Max it was such a tight hub. But it gave way in the end. hope you and your family are keeping well Max. You’re a great subscriber and a good guy in person., I’m glad I got to do your repair last year and had a good old chat.
@maxthecaddy84513 жыл бұрын
@@WMCS thanks buddy , all good mate and i hope the same is for you at your end buddy, might see you soon as my lad needs a new clutch in is mk4 golf 👍
@sudinebabz86513 жыл бұрын
👍🏼 super clutches warrior 👍
@calulau3 жыл бұрын
Me encanta como lo estas haciendo!Me podrias decir por favor que liquido utilizas para limpiar el volante,el palier de caja ,.....etc......el que usas con el pulverizador? Gracias
@alanharwood59663 жыл бұрын
Hi Kevin love to see you work just have a question. You use rubber grease every where that I would use copper grease?? . does this old dog need to learn a new trick?
@WMCS3 жыл бұрын
Hey Alan. The good thing with rubber grease it doesn’t disintegrate. 10 years from now it’ll be as fresh as the day it’s put on. So no oxidisation will happen on the bolt threads. And the clutch plate won’t ever bind on the spline and no premature wear. Let me know your thoughts.
@alanharwood59663 жыл бұрын
@@WMCS sounds good to me thanks for the explanation
@luissoriano-ng6no Жыл бұрын
Gracias es tal cual .me sirvió para mi Peugeot. Saludos desde Chile 🇨🇱 Sudamérica..,👍👍
@jonnyduncan70562 жыл бұрын
Excellent work, exactly the same as my Citroen Dispatch 2.0hdi 2015 and Fiat Scudo apparently
@WMCS2 жыл бұрын
That’s correct. No difference apart from the badges.
@Martin-vf1jm3 жыл бұрын
Hi, Kevin. Using a jack should protect the car body. Otherwise it will soon start to rust.
@bart7055 ай бұрын
Do you also have a "How to" for changing the timingbelt on the same car?
@andyadair852 жыл бұрын
Hi mate great video my I’ve got the same van the clutch seems to slip under load in 4th 5th & 6th would you say that is the clutch? Doesn’t do it in the 1st 3 gears 🤷🏼♂️🤷🏼♂️🤷🏼♂️🤷🏼♂️?
@WMCS2 жыл бұрын
I suppose if it’s slipping then the clutch is slipping
@steveacab773 жыл бұрын
went too look at a low miles 12 plate one today clutch pedal felt real heavy is that how they are on these bud
@johanlarsson7917 Жыл бұрын
Great work Kevin. What LuK clutchkit do you use? LuK SAC 624 3898 00 or 624 4094 00? Can't tell the difference between these two but they are priced very differently.
@martindevries82348 ай бұрын
I am also interested in de difference between these two. Can't find anything..
@johanlarsson79178 ай бұрын
LuK says its the same clutchkit, just two differnt number. The cheaper one is the newest.@@martindevries8234
@PeterPeter-hr1mv9 ай бұрын
Hi, I see most of the bolts are 16mm how about the hex and torx bit size? Can you list the used materials transmission oil quantity? new Luk clutch code?
@darkcrusade57853 жыл бұрын
Good job, you are a beast👌👌💪💪💪🐗🐗🐗 Provides spare torx bits Two gimbal bellows would not have been too much😏
@WMCS3 жыл бұрын
Thanks for the support. I think the torx snapped because of the cold. It was fluctuating -2 degrees and 0 ,
@leondelpirineo55183 жыл бұрын
Very good vidio thanks you are very profesional congratulate you from Spain1🇪🇦
@WMCS3 жыл бұрын
Thank you.
@STREETSTANG073 жыл бұрын
Excellent workmanship! Just wondering how do you determine ahead of time to order or not to order a new flywheel. Also I noticed you very seldom replace the pilot bearing. But this is just my curiosity not to deter from your quality of workmanship.
@WMCS3 жыл бұрын
If there’s a DMF. I will always replace it. Don’t think I’ve come across much pilot bearings. Usually they’re all built in the DMF
@bart7055 ай бұрын
Thx for this very clear video. It was very usful.
@SanyaTsvay3 жыл бұрын
А почему люди не едут в авто-сервис?
@miketigra89953 жыл бұрын
Так удобнее и дешевле. Человек приезжает к тебе и на месте выполняет работу. Официально - дороже(гараж, очередь, запчасти только свои ставят...)
@kamalabbady67783 жыл бұрын
Did you lower the transmission using the jack under the engine or under the transmission it self ??
@WMCS3 жыл бұрын
I lower it from the sump. But don’t like the idea of jacking it up from the sump as the risk of it caving in and damaging the it from the weight of the engine and transmission combined are highly probable.
@castrolgtx50643 жыл бұрын
Why do you leave the criticism comments up? And yet you deleted my comment and other mechanics comments who praised your work?? That guy talking shit about his buddy doing 5 clutches a day taking home 3k a week ffs what planet is he living on. Fantastic video thanks for sharing William
@WMCS3 жыл бұрын
Any comments that are malicious in nature or aimed for a negative reaction from me I will simply delete rather than answer. As an example: wtf are you doing half dropping a subframe.??? You need to take it off. !! Compare to someone that says : is there any reason you only half drop a subframe. Now you do the math. 😊. I appreciate anyone supporting the channel. It’s aimed at helping DIY mechanics out there.
@castrolgtx50643 жыл бұрын
@@WMCS In my experience DIY mechanics should leave it to the professionals.
@WMCS3 жыл бұрын
😁 I remain humble. Anyway hope you’re keeping well 🍻.
@castrolgtx50643 жыл бұрын
@@WMCS All is good thank you
@sp21813 жыл бұрын
Spectacular work.
@WMCS3 жыл бұрын
Thanks for the feedback
@sats78193 жыл бұрын
What a legend
@steveme46653 жыл бұрын
Hey up what happened to the socket you smashed on the pressure plate? Cheap socket brittle? 🤔
@WMCS3 жыл бұрын
Steve I did wonder myself. And the only conclusion I came up with was that the metal snapped because of the cold. It was -2 degrees that day.
@steveme46653 жыл бұрын
@@WMCS yes probably but seems strange it shouldnt do that but these things happen also where did you get your portable light from? What make how much 🤔
@ocsavsaid3 жыл бұрын
What video equipment do you use? The image and the angles are excelente. Keep up the excelente work. I had donne my dispatch 2.0 hdi prior to watching your video. You make it look much easier than it realy is. I didn't take of the right axle though. Does it really make a difference? Thanks.
@RoTtE2k7 ай бұрын
Really good video! Thank you!
@miceinoz11812 жыл бұрын
Another brilliant job!
@edneialmeida76123 жыл бұрын
Bom dia amigo um bom serviço
@paulknowles97272 жыл бұрын
Amazing as usual bud.... How long and How Much? Cheers.
@datwinz39272 жыл бұрын
Hi kev great work are the partner ll 2012 van similar to this sort of job for a clutch change ..?
@WMCS2 жыл бұрын
Pretty much identical
@johnconnolly33203 жыл бұрын
HOW MUCH ARE YOU CHARGING FOR THIS ?
@feyenwilly16833 жыл бұрын
What is the name of drill machine the small red
@driniselmani43807 ай бұрын
Do you know how much Gearbox oil 1.9L or 2.6L?
@petemechanic82493 жыл бұрын
Is that a heater i can hear in the background kev😉 another great video mate. Hope you're well
@WMCS3 жыл бұрын
Hi Pete.,, hope you’re keeping well too. That’s a luxury now at my age, to keep the cockles warm. Nothing like being warm and cosy under these cars in the cold. 😁☀️
@petemechanic82493 жыл бұрын
@@WMCS workshop im in has got a little space heater, doesnt do much but anything is better than nothing mate🤣 got my self a heated jacket not long ago. I shouldn't be moaning lol im only 23
@WMCS3 жыл бұрын
Pete you’re doing great to have your own little business going at that age. Where about are based. I’m lucky in the sense I’m done within about 4 hours then I’m back home.
@evelghostrider3 жыл бұрын
I can feel the cold from here. Ive a parrafin blow heater in my garage at home its never off lol my excuse is its for when I'm spraying I need parts warm 😅 old age cold and to many motorbike accidents cause the bones to hurt lol great outside work again chum 👍👍
@mrgrumpy51163 жыл бұрын
@@WMCS I need that heater at my age, just came up from the garage and it is bl----- cold down there, thought I'd finished with concrete floors when I retired .. but not so, hope you had a few days off, and looking forward to a nice warm summer.
@rockinnathan3 жыл бұрын
What's the deal with the pre load crap on the relay clutches.
@chindraledger68733 жыл бұрын
I like your work it's was very helping me , but please use safety eye glass
@WMCS3 жыл бұрын
Thanks for supporting the channel. I appreciate the word of caution.
@actionnait8479 Жыл бұрын
Tres beau travail , trés belle vidéo , very very goog job , thank you
@musicgangster28433 жыл бұрын
Good job Kevin 👌
@sevill13 жыл бұрын
El mejor de todos
@paulbillingsley76453 жыл бұрын
I have a fiat scudo same van is there enough room to take the gearbox out completely mine has a problem on 4th gear synchro
@WMCS3 жыл бұрын
Me personally I would slowly wiggle it out. For you personally you’d need good judgement within your own capacity.
@paulbillingsley76453 жыл бұрын
Thx for the info
@paulbillingsley76453 жыл бұрын
@@WMCS would you know if changing the 4th synchro is a difficult job are there any special tools needed ect
@bobbobby57243 жыл бұрын
Fantastic video
@seelan1919193 жыл бұрын
Very best job i know how hard with working in colder wether and underneath of car ! Me auto mobile mechanic! Ex jaguar technician! Good job!
@WMCS3 жыл бұрын
Great to hear from a fellow mechanic. Really appreciate your feedback and supporting the channel.
@stefanomaletti30853 жыл бұрын
Bravissimo!
@WMCS3 жыл бұрын
Grazie mille 🍻
@ignacioandreslabrinsanchez32993 жыл бұрын
Felicidades por tu gran video!! Desde chile
@audia4addict9503 жыл бұрын
How much for audi a4 B8 2010??
@rb64913 жыл бұрын
Was the offside inner cv joint boot split? And how good are those heaters? Diesel?
@WMCS3 жыл бұрын
That heater is the best I’ve had. Definitely split the inner CV.
@oldiesoutdoors583 жыл бұрын
great video .... and great skill ..
@awsomefnafbirds18043 жыл бұрын
I got a similar car to this one do these have solid flywheel or they’re called dual mass which might be same thing how do you match the clutch with it ??
@a.b.c.5203 жыл бұрын
Replace this crappy dual mass by a mono mass
@francoislaval55243 жыл бұрын
Did you put on a gimbal boot collar? All the fat centrifuged ...
@WMCS3 жыл бұрын
No I didn’t. That’s for the garage to do. Customer’s always made aware tho.
@ricosalditos45703 жыл бұрын
Great job 👍
@Genovaa-8 ай бұрын
C’est boîte 5 ou 6 vitesse ?
@p00ky764 ай бұрын
Are you AI? While watching your video, I asked windows copilot why you need to remove the front axels when replaceing the clutch on a peugeot expert & it gave a brief explanation about accessing the clutch assembly & then pointed me right back to your video. I guess our AI overlords aprove of your Ninja skills :D
@WMCS4 ай бұрын
I am the very first Generation in full operation
@airlessman517Ай бұрын
Thanks you my friend
@fabriceleroux23963 жыл бұрын
Nice vidéo And Many thanks for this sharing that vert help us
@stoiancostel51473 жыл бұрын
Hola amigo me gusta tu video un saludo de Madrid
@WMCS3 жыл бұрын
Hola ... and saludos ☀️
@stoiancostel51473 жыл бұрын
@@WMCS Gracias amigos un saludo de Madrid te espero cu un bmw F 30 amigos
@claudiaaguilar57912 жыл бұрын
what is the torque of the flywheel bolts?
@markacollins31023 жыл бұрын
Kevin, where did you get your top and bottoms from, I could do with a pair of those, colour also, just wot I need
@WMCS3 жыл бұрын
It’s a Gorka 4 bars.,, I think you can find it on eBay now.
@jensbo79833 жыл бұрын
Gute Arbeit, aber bitte nimm das nächste mal eine Gummiunterlage für die Wagenheberaufnahme ... Grüße aus Deutschland ...
@driniselmani438010 ай бұрын
Ich komme gerade aus der SelbsthilfeWerkstatt. Das Video hat enorm geholfen. Ohne Kevin hätte ich es nicht geschafft. Es gibt aber 2-3 Punkte was ich als kritisch gesehen hatte. Ein davon ist das was du gesagt hast. Die Ölwane war richtig belastet. Das gewicht war tatsächlich sehr groß. Ich habe wie du sagtest eine Gumimatte geholt. Ich bin von 12:00 bis 20:00 Uhr und noch nicht fertig. Morgen mache ich weiter...
@nigelstrarup3 жыл бұрын
Hi good one love how you do this keep up the good work 👏 👍
@WMCS3 жыл бұрын
Thanks for the feedback and really appreciate your support of the channel.
@nigelstrarup3 жыл бұрын
Thats fine love it and look forward to seeing more 😊
@kamiondzija19863 жыл бұрын
Well done bro💪💪💪💪This car doesn't have a DMF?
@WMCS3 жыл бұрын
No DMF .., but a heavy duty clutch.
@kamiondzija19863 жыл бұрын
Thanks bro
@mahjouba20063 жыл бұрын
Hello, thanks for your videos. Please can you show me the elecrical screwdriver name that you are using. Thanks.
@Pedro-cs5fh3 жыл бұрын
Milwaukee Fuel ONE KEY M18 ONEFHIWP12-0X
@budj78983 жыл бұрын
What clutch alignment tool is that?
@oneplus9813 жыл бұрын
Super :)
@vec50513 жыл бұрын
and how much Nm does this electric wrench have?
@WMCS3 жыл бұрын
It’s adjustable the Nm. But it can go up to 1400nm.
@vec50513 жыл бұрын
@@WMCS Thanks for the quick reply. I realized.
@raulmorais95103 жыл бұрын
Ferramentas top
@lrdisco20053 жыл бұрын
What's your opinion on under trays on engines?
@WMCS3 жыл бұрын
A bit of a contentious subject 😁.,, but in my opinion unless it’s an off road car I don’t see much of a point. I’ve seen cars without undertrays the engine looking spotless and cars with undertrays looking like a rust pot.
@lrdisco20053 жыл бұрын
@@WMCS I also find they hide small fluid leaks.
@castrolgtx50643 жыл бұрын
@@lrdisco2005 which is handy with a over cautious Mot inspector 🧐