2016 vw passat p0016 p0300 fix with data

[@enobishop1419]

Breath analyzer!? Wow! Is that to keep the old drunk from driving after one too many? Oh man I had no idea such things existed? lol! 😂❤😂

[@tedjohnson64]

Very interesting case study! I especially liked the merged specified/actual camshaft adjustment values graphs, with the old and new solenoids (vvt manets), Also, is that actually a picture of you (the huge body builder doing a “most muscular” pose in the channel icon)? Very impressive!

[@partsshooter]

Thanks... Yes. That's me in the photo

[@DuaneDonaldson]

Prevents theft, you are so funny dude, that breath analyzer prevents drunk people from driving, there is no shame in calling an alcoholic an alcoholic.

[@carlospiezzi4030]

Good morning sir, after watching your video I wanted to take advantage of your knowledge to make a question about a similar problem that I have in the workshop with codes P0011 and P000A, the intake magneto can be exchanged with the exhaust one to check if the code passes to the exhaust tree, thank you very much

[@enobishop1419]

Keeping us busy

[@Whereistes]

When taking off the piece to the valve I cleaned all the dirty oil inside should I put clean oil in there like you did ?

[@partsshooter]

Totally discretionary.... it just go on easier

[@golfmaniac007]

Would cleaning up the magnetic actuator part work?

[@partsshooter]

@@golfmaniac007 you have the best chance that will work only if the pintle is stuck and sticking. Typically the component is weak and need replacing

[@aliennemesis0663]

My mk6 is having. P0011 code along with misfire codes and p2187 po347. Change camshaft sensor still misfiring bad at idle. I check the timing and the timing is in time.

[@partsshooter]

Does it run bad during start up? How was your oil quality?

[@philpots3216]

Misfire, have you taken out sparkplugs and looked at them, maybe time for new coilpacks n plugs, also if you got a pressure tester for valves whilst you got sparkplug out, May aswell test cylinders 👊

[@osmanomar9114]

What is the name of that piece I have to buy it. Thanks

[@mackyj388]

You do not wish you had one on your car. Lol

[@markevenswenson4363]

Where can you get new bolts for the adjuster magnet

[@partsshooter]

You can go to your local part store and match the thread pitch, you'll get a generic 10mm head bolt likely. But not factory. May look tacky but it'll work Or take the thread pitch and match with one on Google.

[@philpots3216]

I went to vw main dealer, 8 bucks for 6x screws

[@worldfitnesstrainerradekve9234]

How mechanic start the car in covid world 🌎 👻 😷 🙊

[@KennaBog]

passat

[@KennaBog]

what is passa

[@enobishop1419]

Hey I think my Audi A3 has the same engine...? I have learned a lot of shit just for trying to DIY .., don't get me going - I'm in California-emissions nightmare Now I know

[@enobishop1419]

Bro I'm just saying I keep having issues with sensors keeping me from registering my car still - I gotta change something else Runner position... there are things that are in place to keep me from moving forward... I swear... kzbin.info/www/bejne/qZvMoXVvZbBoZ80si=EIcKlVDUQ2RzVArZ

[@MegaHollywood1971]

A breath analyzer 🤣 At first, things may appear to be good - but if the phaser is bad, the problem will return as soon as it recieves higher RPM. O-Rings are like $1.50 and at 100Kmi + those are well overdue. Good luck.

[@partsshooter]

Please... for the life of me, explain how an o-ring causes fluctuation of data? I beg you to elaborate

[@partsshooter]

I typically misread... I do apologize if I did. But text offers no context, so Im asking for clarity

[@MegaHollywood1971]

@@partsshooter When you replace components (especially with higher mileage) it is imperative to replace the seals that go to the components. The O-Ring abrases around the outer diameter of the magnet and provides that critical seal for oil seeping through. If it is even slightly worn, it will bleed and clog the Adjuster magnet again. I am surprised that your Intake readings were coming out better after you did this; as the majority of the time the phaser is usually damaged as well. You can tell if the phaser is damaged by "how far out" the center pin to it sticks out. Looks like the Primer to a rifle cartridge. Should be "flush". If it is protruding out, then the spring mechanism has failed and it will need to be replaced. Don't know your predicament, however in most cases, once you hear the increased clacking - more problems arise. There are numerous components and practices that increase the happening of this: 1) PCV (even a slow failure) 2) Purge Valve (vacuum leak) or any other vacuum leak over a longer duration. 3) Oil change durations Euro cars take so much coddling and preventative maintenance, and even then things go awry... Hope you get more life out it 👍