2018 Infiniti Q50 Advanced CANBUS CAN HI CAN LO Diagnostic/Troubleshooting Isolation and fix! Part 3

[@globalcommerce7654]

Buy the ULTIMATE CANBUS tool HERE!: www.ebay.com/itm/354992141640

[@zexxmcazi2134]

Hie buddy I have been battling the same U1000 code I have done all I can on a maxima 2014 sv model the climate control just died out it's not turning on at all I am so confused 😅 never had a code like this one since I worked I my new work place

[@MrPrplhaze1]

Im trying to fix a similar issue on my 2012 G37xs right now. Im getting Engine: U1001 and ABS: U1000. At one point is was same code on Meter M&S? also. Some days my tcs/AWD system works great, no codes, other days neither of them work, with only those 2 codes showing. This video encourages me to test more. You also mention programing the ipdm with a "im608". How do we do that? Any other advice greatly appreciated!

[@Vell22]

You ever get it fixed ? I’m having the same problem as we speak code. U1001 I’ve already replaced and reprogrammed the ECU

[@MrPrplhaze1]

​@@Vell22 Unfortunately no. I watch videos like this try to learn something, but the authors never answer me. Right now, the only light on dash is a tcs light.

[@KennyPicasso]

Hey bro I’m battling a C1138 4WAS code after an accident I had, not getting power steering, any idea why? I’m getting all sorts of circuit and communication problems

[@invoicedkey7397]

Hey any help, I have a 2015 hybrid I recently got, the car runs and drives good but after sitting for a few days the car needs a jump start again. I charged the battery a few times. Could it be something draining the battery or could it be something else. Dash just flashes, horn doesn’t beep or trunk doesn’t release.

[@globalcommerce7654]

it could be your battery, troubleshoot it

[@junbefit5482]

Hey can you help with a Infiniti m35hybrid

[@trikxy3422]

Have you ever had a infinity Q50 come in with a problem like , while driving , the cluster turns off and only the intouch screens stays on but the car is on , the steering wheel starts getting hard to turn.

[@MrGenius34210]

My Q70 keeps throwing a P0720 code. Got a used Valvebody replacement and replaced the output speed sensor. Atill getting thr codes after reset.

[@Kingdon_30]

Hey, I'm having a issue with my q50, my sunroof drain clogged and dripped water on the drivers side, the car starts without my putting my foot on the brake I'm not sure which module to look at. Any help?

[@globalcommerce7654]

I would start with brake pedal switch, disconnect it and see if behavior is the same..

[@zexxmcazi2134]

Hie am having the same issue my head is heavy Iof trying to get the car fixed i got U1000 code the climate control died out and i had cleaned all earth wires but the code still there the climate control not powered signal off code

[@danielc4251]

how do you open the fuse box , please help

[@emekanwadani2906]

Bro you have they same problem with my infinti FX35 no communication no start after flooded

[@Vell22]

You ever get it fixed ? I’m having the same problem as we speak code. U1001 I’ve already replaced and reprogrammed the ECU

[@urboyace23]

How do I open it up like that

[@healthystyle]

Great Video

[@globalcommerce7654]

Thanks

[@jeffhung8896]

Good job!

[@vq_tyler_nyc4054]

Yo I have codes engine u1000 abs u1000 das module one u1000 awd u1000 chassis u1000 what could it be

[@globalcommerce7654]

Hey! Those U1000 codes usually point to a communication issue between the modules in your vehicle. It could be a problem with the wiring, connectors, or even a faulty module that’s causing a loss of communication. Make sure to check for any damaged wires or loose connections

[@TR42000]

Bro my infinity Q50 RWD 2018 I have an issue with my odometer ( all my warning lights and indications are not working except ( airbag sensor ) The rest are working fine I just don’t have any warning lights any hints bro ? Thank you .

[@globalcommerce7654]

Does the car work normally? Have you attached a scanner and checked for codes?

[@rjjohn6415]

If i replace my IPDM with a use one from Q50 does it need to be reprogramed or is it pull and go?

[@globalcommerce7654]

Yes it must be programmed.

[@mikess323]

@@globalcommerce7654 what exactly did you need to be programmed? I thought the fuse boxes didn't need programming Great Video by the way.

[@globalcommerce7654]

@@mikess323 hit thumps up my friend, on this model security is tied to ipdm, must reprogram keys.

[@lane5480]

【ｐｒｏｍｏｓｍ】