this bike goes faster than 20 MPH so before anyone else comments about the fact that I was only going around 20mph on my bike should read this first not last hopefully this helps clear up any confusion regarding top speed.
@theatom72647 жыл бұрын
For a 212cc I would hope so. Nice bike man.
@carlschock67476 жыл бұрын
We realize that, but people would rather see the 50 than putting around. Thats like posting a 300 lb bench press and then showing 50lb, doesnt quite make sense. Nice bike though
@nickhersheys27066 жыл бұрын
I highly doubt that. It's too heavy.
@fishfire_29996 жыл бұрын
jefff163 why would you even show the spedo if u didnt intend to open it up ???
@causwayspeedway6 жыл бұрын
Nice build!! Would like to see 50mph though.. legal?
@JediPolock7 жыл бұрын
Holy Damb man! 212cc!? Really officer it's only 50ccs ;D I love it, great build. Way to grease a shoehorn getting that engine on that bike
@michaeldesilvio20608 жыл бұрын
that exhaust pipe looks dangerous like it would burn your leg.
@jefff1638 жыл бұрын
no but it did burn through two pairs of pants. and that's why I put a makeshift heat shield on it.
@michaeldesilvio20608 жыл бұрын
jefff163 It's really cool
@rachetCD7 жыл бұрын
jefff163 how much was this?
@jefff1637 жыл бұрын
this bike cost around 1000 with all the extra parts
@theatom72647 жыл бұрын
Jefff163; Not bad. I payed about or a little more than that for a Honda friction drive bike I put together last year mostly because the bike by itself costed $600.
@willyam97354 жыл бұрын
Looking down the whole time was almost enough to make me "ralph". At least look up once in a while so we can enjoy the ride vicariously! Nice build!
@1949kf7 жыл бұрын
With the Comet variable ratio drive and 6.5hp ohv 212cc harbor freight predator that bike should fly. Should be good for an honest 50mph ..maybe more
@owenclough71565 жыл бұрын
I heard someone got theres up to 65, without removing the govener
@dahomieplaysthegame71133 жыл бұрын
Put billet parts in. Now it does 70
@kushpaladin3 жыл бұрын
think he was intentionally not going flat out because he was carrying camera with one hand and other on the bars. going over 20 with one hand great way to get your teeth knocked out and a good ole roadrash
@tonipereira87114 жыл бұрын
Best motorized bicycle I"v seen yet.
@jerryb12342 жыл бұрын
Nice bike, thanks for sharing.
@YoLo-dc1uy4 жыл бұрын
I'm building a clone now with 3.10 lift Dyno cam, dual valve springs, 1.3 roller rockers's making around .530 lift, with a 1.75lb billet Arc. Flywheel. With a 3 disc bully clutch. Using the carb off of a Kawasaki kx85, a flat top piston .020 longer rod, paired with a gx160 head that's been worked to unshroud the valves to make power in the high rpms. By allowing the high compression closed chamber head to flow)breath at high rpms like a open chamber head does. Yet also providing the benefits of the high compression low rpm torque monster effect. When a gx160 head is used on a 196/208/212's
@a1930ford4 жыл бұрын
Mufflers are hotter than hell when they burn your skin. That one sure looks like a challenge in just keeping any hide on your inner legs as you ride. Loping engines always sound odd. Nice looking bike and motor combo, but I'd have to do something about that muffler being where it is located, for sure. :-)
@davidchapman35636 жыл бұрын
Wow thatthings cool,nice,amazing i dunno not enough words to discribe it!ive seen alot of builds n this is by far my fav.!!!nice work
@MiguelMartinez-er6ex6 жыл бұрын
I want to tell you that you are my hero, love that bicycle
@SilverShadow2LWB7 жыл бұрын
Nice job putting this together. I like the sound. Unfortunately we can't ride something like this out in S. Calif., if it doesn't pedal or with a motor of this size. We would be limited to off-road only.
@TheShowgunofHarlem Жыл бұрын
Well that's because California is a piece of dog shit state ran by a bunch of brainless tree hugging soy boys.
@ahmaddarwish14867 жыл бұрын
get the widened pedal set. I know not having the cvt cover on it looks cool, but that thing gonna eat your leg, which isnt good a 40-50mph
@jefff1637 жыл бұрын
I already have a wide pedal crank but it would not fit right so I put the normal one back on. and also I got at least three or four inches of space before this thing can sink its teeth in my leg or actually my ankle since its in-between the two front drive pulleys. and the side cover sticks out so far it blocks my foot from reaching the pedal.
@trentbrockus87477 жыл бұрын
how did attach the rear sprocket to the hub I have a bike with rims like that the only way I could see is to drill hole threw the sprocket and attach it to the disk brake with five Allen bolts so or weld it on?
@jefff1637 жыл бұрын
I put some spacers and bolts from home depot in between the sprocket and the disc rotor
@robertmiller45805 жыл бұрын
Cool I was thinking maybe with a small pull behind trailer like if you had a child trailer that has been modified to do so
@logainfalsedragon3587 Жыл бұрын
I'm all about the braplife, but this is a nice looking scooter
@a1930ford4 жыл бұрын
I know that I must be missing something, but I believe I would have to be bow-legged in order to ride with the engine and such mounted in that manner. Lord help me if I ever caught my big feet up as I put them onto the pedals when riding. It would have been nice to have seen you on the bike and see what that looks like as you mounted it to ride.
@heavystarch1004 жыл бұрын
It's awesome but in the future that frame is going bye bye! But by this build I think you know that. Get a purpose built gas tank frame! Nice video
@axegod86138 жыл бұрын
Get yourself a 3D Motorsport manual clutch. They are new and the only manual clutch for these engines on the market. Cheaper and better than a CVT transmission, too. You can also pedal start like the 80cc bikes with these clutches and get rid of the pull start. You can thank me later.
@jefff1638 жыл бұрын
I thought about getting one of those but there not cheap. I also like my pull start monster.
@axegod86138 жыл бұрын
Okay, well most people don't like having the pull start on their engine so I thought I'd let you know.
@eclipsegaming59987 жыл бұрын
big disadvantage not having the variable transmission tho
@jefff1637 жыл бұрын
Eclipse Gaming there is a big disadvantage if you're using a centifugal clutch since the torque converter has the most power in terms of taking off and acceleration and it's much smoother than a centrifugal clutch but it cuts down top end speed by about 75 percent from what I noticed so I stuck with the torque converter.
@kxlucifer7 жыл бұрын
Axe and theres people like me who like the like feature like electrict start everything between the 212 preddy and my powerland are similar.i uses 212 headers and carb filther adapter as well as the plate.
@jimbokainawildes95057 жыл бұрын
nice build brother!!
@jefff1637 жыл бұрын
Jim Wildes thanks
@radorezz76274 жыл бұрын
Yea man sweet build. I was going to do this but was wondering if the frame could handle so much torque
@RexFixx3 жыл бұрын
Lol... 6.5hp 1 gear
@JAM-zb2vh2 жыл бұрын
Hello What frame is that I would like to build one for my Father so he can ride with me thank you
@reyarturo95362 жыл бұрын
I'm trying to do same with electra frame and briggs & stratton engine
@charlietrumpet1266 Жыл бұрын
How close are your legs to the muffler? Looks to me that you can get burned easily.
@juliemoon48937 жыл бұрын
No issues with those mags? I want to get a st but I am scared of them cracking.
@MendezMotorizedBicycles6 жыл бұрын
Ok jeff i have the same bike frame can i please have the link to the front forks that you used 🤞
@@jefff163 can you still pedal the bike without hitting your legs?
@thedude54724 жыл бұрын
Sweet build! Where did you get that triple tree from?
@zuulthemonster32226 жыл бұрын
Ι dont think that the top speed is only 25 mph!!
@kushpaladin3 жыл бұрын
i highly doubt anyone is dumb enough to go over 25 mph with one hand carrying a camera and other on the bars
@TrickMini4 жыл бұрын
I would never open this up more less ride it, look close at the frame being pounded in and the cut off support bar. Danger waiting to happen.
@DaBuGzLiFe7 жыл бұрын
Really nice bicycle. Why go through all the trouble and not get a dirt bike?
@jefff1637 жыл бұрын
DaBuGzLiFe I have four dirt bikes already.
@jimfitzgibbon54925 жыл бұрын
Love you bike & set up. What frame are you running. After my build I have going now I really want to build one with a predator. I love the power they have, but I love the sound better. But I need to start thinking of what frame I need. I really like yours, so that is why I ask what bike you have.
@mariosalazar35842 жыл бұрын
I like your forks. Where do you get?
@nickhersheys27066 жыл бұрын
What bike frame is that? I also noticed that you flattened the front tube. That might compromise the strength of the frame. I currently have a 79cc Predator mounted on a Huffy. Lacks low end torque, so I'll upgrade to a CVT torque convertor. Planning to build my next one with a 212cc. Thanks.
@jefff1636 жыл бұрын
This bike is a old huffy cranbrook frame
@zedee20003 жыл бұрын
Can you ride the bike pedaling it with your feet? If you're hitting the engine are you hitting the muffler with your leg? Does it go off-road up some hills pretty good?
@robertmiller45805 жыл бұрын
Would love to use it for hunting/scouting so will it pull a light trailer like a kids bike trailer loaded with a deer and maybe a few otherthings
@jefff1635 жыл бұрын
I don’t know about a deer but the other stuff it will definitely haul it has a lot of power.
@justinc86386 жыл бұрын
Jeff nice build man I'm building a 212cc bicycle. Question are the torque converters they sell for go carts the same as kingsmotorbike torque converter?
@jefff1636 жыл бұрын
I’m not sure.
@robertmiller45805 жыл бұрын
Cool what is the speed and torque with it and how much will it haul in weight
@tylerdalling86826 жыл бұрын
Anybody notice how crooked his handlebars are
@davidcrunkmd5 жыл бұрын
Am pretty sure it's the camera angle, perspective. Looks straight too me.
@robertramos19728 жыл бұрын
Cool bike like the front forks where you get them and any adapters to make it fit that frame
@jefff1638 жыл бұрын
I got them from fuhuasports on eBay
@robertramos19728 жыл бұрын
jefff163 what about the wheels
@jefff1638 жыл бұрын
I got the wheels from gasbike.net but I would recommend getting some on EBay
@joneserupinsmoke91612 жыл бұрын
Damn that's a big set up what u hitting 45
@reyarturo9536 Жыл бұрын
I have the ingenie where I can find the others parts ? thanks
@ahmondeboxley29507 жыл бұрын
How can I get one of these built I already have a brand new bike get at me nice video
@jefff1637 жыл бұрын
you can order the engine kit at www.gasbike.net and I have seen one of these in a KMB GT gas tank frame but that might require the CNC head. if you look at my other video I actually put this engine in a NEL LUSSO frame and it has a CNC torque convertor mounting plate that wont snap in half I would recommend to get one of those if you do plan build one of these kind of bikes.
@harryburford66294 жыл бұрын
lift the camara up it would give a better look at stuff and stated speed overall great video
@djbillye49437 жыл бұрын
similar to mine,good job.
@MrCbell576 жыл бұрын
What is it about 20 mph. Is it that under 20 you can ride on the street with this bike? I don't think gas powered bikes are legal anywhere in the US.
@MrCbell576 жыл бұрын
Sorry was not informed of exactly what it was and how fast it went. Or where you can ride gas powered bikes. All I see is kids getting pulled over by cops. Just asking. Yes I know this one bike will go much faster. But as a rule electric bikes are only legal if you stay at 20mph or under.
@tjgj64435 жыл бұрын
What kind of bike is it please tell me so I can get my engine to fit
@roonimac5 жыл бұрын
did u find out cause i need to know as well
@Jeff_Green5 жыл бұрын
Predator 213
@racrx75 жыл бұрын
Sweet build man👍🏻 Who makes that CVT?
@Sauron_Green3 жыл бұрын
What did you do to the frame it's a mess
@wintergreen827 жыл бұрын
so with the muffler so close to your legs it doesn't heat up and burn you?
@jefff1637 жыл бұрын
zavier wintergreen it only burns pants if I don't have the makeshift heatshield on it.
@wintergreen827 жыл бұрын
so if you ride for a long time the engine doesn't heat up? what about the smell..after you take a ride i'm guessing you get an engine/gas smell afterwards..i'm asking cuz i wanted to know if i could still store the bike in my room afterwards..also what kinda brakes do you use? going fast you gotta have better brakes and not just the regular bike brakes, right?
@jefff1637 жыл бұрын
I am using a cheap hydraulic disc brake from eBay and yes you most likely will have a gas smell after riding the bike but I think if you drain the carburetor and gas tank after each ride I would think the gas smell wont be as strong but I don't recommend that if you are going to ride the bike a lot.
@Revdonlee748 жыл бұрын
What is your top speed running the torque converter right to a rear sprocket? I'm getting ready to put the same setup on a tandem bike that will run the torque to the rear pedal sprocket which will then run through the 21 speeds the bike has, but will need a heavy duty derailuer. Was just wonder what top speed was going directly to the rear wheel?
@jefff1638 жыл бұрын
I have only got it up to 48mph but it keeps throwing the chain off cause the torque converter belt pulls the rear pulley towards the front pulley causing the front drive sprocket to tilt letting the chain to slip off but I think it could do about 55 to 60mph.
@Revdonlee748 жыл бұрын
Thanks. I wonder if the rear of the torque converter could be bracketed to the seatpost on the frame to stabalize it, maybe with some plumbers pipe hanger tape. I can't wait to start building mine. ( ; ) )
@jefff1638 жыл бұрын
have fun with the build
@fastrccarz2 жыл бұрын
a tweeker on a good day!
@codeman1764 жыл бұрын
what is behind the torqe converter ?
@doomracing55275 жыл бұрын
How does that statement mean anything? It only went 21 or 22 mph. I hope when the clutch bites your leg ( thats read as when. Not if) your going slow, and not go down to the left. Your leg is going to get chewed up bad. On the lighter side its a beautiful build! Well done!
@duskintheforest584 Жыл бұрын
No crank mod so pedal clears?
@Steve_Just_Steve6 жыл бұрын
Jebus, what did you do just bash the downtube with a hammer? I'm sure it retained all it's structural integrity.....
@jefff1636 жыл бұрын
I used a sledgehammer actually and it worked fine for me till I got another frame.
@realm30393 жыл бұрын
Try change the seat to motorcycle seat it will look cooler
@CORRIGEEN717 жыл бұрын
like the wheels where did ya get th e m?
@Zak_How7 жыл бұрын
Read the description it does 50, he has his phone in one hand he isn't gonna do a speed run like that, also why go to all that an not get a dirt bike for me would be less likely to get pulled over
@jefff1637 жыл бұрын
raamastak1 I have a dirt bike and I also have a Harley Davidson Sportster but these bikes are much less of a Hassel when it comes to maintenance and repairs.
@Scootertuner10007 жыл бұрын
You need to cover that front pulley. It's dangerously close to your left pant leg. If it grabs the denim of your pants it will rip your leg off before it's done.
@jefff1637 жыл бұрын
I don't wear denim so that that wont work and I have had my pant leg caught in there before and my leg wont just rip off cause this isn't a movie. and to tell you truth them cover are retarded looking and I wont be able to reach the pedals cause it sticks out to far. but thanks for your concern anyway.
@Scootertuner10007 жыл бұрын
You don't were jeans? That's unusual. It won't literally rip your leg off, but it could injure you. You can make your own cover that is more streamlined.
@jefff1637 жыл бұрын
I also had the front pulley explode and it scratched my leg but I didn't notice it until I felt the blood drip onto my leg
@leavehuh77442 жыл бұрын
do u get burned on the exhaust?
@roonimac5 жыл бұрын
Hey bud which motor is this and bike?
@2EZY4Me27 жыл бұрын
How did you mount the sprocket and disk on the back together ?
@jefff1637 жыл бұрын
with some bolts from home depot and spacers its kind of a trial and error type when installing.
@AlvinSmith6 жыл бұрын
What frame did you use for this project?
@JoseDiaz-ug1xo5 ай бұрын
Looked like he smashed some of the frame, wtf!
@ReiMonCoH4 жыл бұрын
Is that the Grubee HD rear hub?
@niteshades_promise5 жыл бұрын
beast mode +9000🍻
@kenardodanvers85978 жыл бұрын
What type of bicycle is that ? Wow
@jefff1638 жыл бұрын
its a huffy
@penguabob7 жыл бұрын
what kind of huffy exactly and also what size im trying to build one similar with a 212 and was wondering what the best size bike is to use and any tips for installing and using/maintaining the bike
@jefff1637 жыл бұрын
Ziggy Salmi I don't recommend this frame cause i had to hammer the frame for it to fit and one of the rear wheel mounts has cracked.
@ianmoone46426 жыл бұрын
What motor mount did u use... I got one but it don't match the bolt patterns on the motor.... SmFh
@AlvinSmith6 жыл бұрын
What steps did you take to prepare the frame to accept the engine? I picked up a Cranbrook to use for my project.
@TanBoiIndustries2 жыл бұрын
good luck with that cranbrook
@N9197U2 жыл бұрын
@@TanBoiIndustries no way he fit it, I have a 79cc and it clears Cranbrook by 2mm.
@TanBoiIndustries2 жыл бұрын
@@N9197U yea the one in the video has major mods to the down tube and probably the seat tube
@N9197U2 жыл бұрын
@@TanBoiIndustries probably has 0 integrity, that frame is paper flat
@speedyclipz64644 жыл бұрын
CAN SOMEONE TELL ME WHATS THE NAME OF THAT FRAME
@CrumbleMachine7 жыл бұрын
awesome...
@Scootertuner10007 жыл бұрын
Nice build though. Surprisingly slow though. WHy is that?
@jefff1637 жыл бұрын
its slow so I don't break the torque converter again.
@Scootertuner10007 жыл бұрын
How did the TC break?
@jefff1637 жыл бұрын
throttle wheelie broke it they are made of junk pot metal.
@-Opiate-7 жыл бұрын
Charles Arthur earlier he said it would top out at 50mph, but he was holding camera etc so cruised at only 20.
@Scootertuner10007 жыл бұрын
I see. I have built a few of these and they've always been fast as F.
@N9197U2 жыл бұрын
world most dangerous frame
@ThePlanet_L.I.6 жыл бұрын
U have a pull system engine can u start it with a drill as well ?
@jefff1636 жыл бұрын
it might be possible but I prefer the pull starter.
@ThePlanet_L.I.6 жыл бұрын
jefff163 👍🏾
@mushumokomodo3 жыл бұрын
whats wrong with it, why wont it go? poor guy...
@G33_528_7 жыл бұрын
I need the name on the back sprocket
@jefff1637 жыл бұрын
it a manic mechanic sprocket that you can get on eBay. they usually cost around 40 to 70 dollars depending on where you get it.
@myjourney32315 жыл бұрын
Where did you buy this bike kit?
@kalebbrown85457 жыл бұрын
How fast and how heavy is the whole thing
@jefff1637 жыл бұрын
The top speed so far is 48 MPH but my speedometer was not working right so it could have been a lot faster than that . and I think it might weigh around 50 to 75 pounds.
@AlvinSmith6 жыл бұрын
What did you use for your makeshift heat shield?
@zippyxp34662 жыл бұрын
An old fender
@tristaterider78408 жыл бұрын
What's up man? I used to have a 66cc 2 stroke bicycle. Anyway I was thinking about starting a build with this motor. How fast did you get that bike to go and how much did you invest into it? Thanks for uploading Subscribing for more!
@jefff1638 жыл бұрын
I invested about 880 in everything but the frame and so far I have only got it up to 48.4mph its worth building but I always have to worry about the torque converter snapping in half if I give it to much throttle.
@jefff1638 жыл бұрын
I broke two already.
@tristaterider78408 жыл бұрын
damn man. those are about as expensive as the engine itself. Thanks for uploading
@jefff1638 жыл бұрын
my advise is the 49cc kit with the grubee belt drive kit even though I have a chain drive model the belt drive is better for acceleration if adjusted right.
@tristaterider78408 жыл бұрын
I still haven't decided for sure but I might just custom fab the whole thing although advice is always welcome
@eduardodiaz57625 жыл бұрын
Install a 10L cafe racer Gas tank and that Bike would be Done. Imagine the gas mileage on a 2.6gallon tank with a motor like that!
@jefff1635 жыл бұрын
Eduardo Diaz 10L gas tank never heard of one but the newest version of this bike that I have has 1 gallon whizzer bike gas tank on it and it has very good mileage.
@eduardodiaz57625 жыл бұрын
eBay sells universal gas tanks for motorcycles, it seems we can weld some bolt to screw it in place in a bicycle, it seems like a good alternative to these small flimsy gas kit tanks.
@mikeperdue44176 жыл бұрын
She's a Beauty. If she were mine I'd put a springer front end on her.
@mechworks98347 жыл бұрын
Yo bro what speedometer is that ?!?
@jefff1637 жыл бұрын
its a dashboard 150 from Walmart.
@charlescrom42386 жыл бұрын
How did you get the sprocket on the back side
@jefff1636 жыл бұрын
Charles Crom the sprocket came with this engine kit from gasbike.net so the sprocket was already installed but the transmission plate snapped in half so I ended up getting a new one from eBay so I would not recommend this type of tourqe converter if you check out my other videos you'll find a video of a Nel lusso with this engine shoved into it and a different tourqe converter That I modified.
@charlescrom42386 жыл бұрын
Did you have to modify the shaft to get the sprocket on the backside of the mounting plate?
@charlescrom42386 жыл бұрын
And where did you get that intake?
@jefff1636 жыл бұрын
Charles Crom not really it just needed to be shoved with a little force but not every thing works the same for everyone of course
@jefff1636 жыл бұрын
Charles Crom here's a link for the intake and carburetor m.ebay.com/itm/22MM-MIKUNI-CARB-KIT-PREDATOR-212-GX200-GX160-HONDA-CLONE-Drift-Trike-Mini-Bik/252314674798?_trkparms=aid%3D222007%26algo%3DSIM.MBE%26ao%3D2%26asc%3D20171010182013%26meid%3D93416cb1ae4f49169f31a648c57d3857%26pid%3D100890%26rk%3D10%26rkt%3D12%26mehot%3Dpp%26sd%3D162727020554&_trksid=p2056116.c100890.m2460
@billmase24586 жыл бұрын
Your bike only goes 20mph?
@MrYoshio145 жыл бұрын
Wtf happen to ur bike frame?
@jdsolberg7613 Жыл бұрын
You were only going around 20 mph!
@randygrindle51217 жыл бұрын
haha sick man
@МикитаКостюшенко6 жыл бұрын
What is it engine?
@ABCDEFGHIJKELA...7 жыл бұрын
looks like half a Virago motor.
@bvdp36777 жыл бұрын
I still don't know how to shift it
@jefff1637 жыл бұрын
what do you mean shift it.
@LaukSmith7 жыл бұрын
It has a CVT it is automactic, no shift
@robertmiller45805 жыл бұрын
Nice bike is it a 2 stroke or 4 stroke
@jefff1635 жыл бұрын
4
@luisoti17432 жыл бұрын
The muffler is too close to your leg,be carful
@roonimac5 жыл бұрын
what bike frame?
@justauser7 жыл бұрын
212cc? This is hardly a "bicycle" 😂 sometimes my 66cc feels like a motorcycle once I get her going nevermind this!
@justauser6 жыл бұрын
BlueWise NinjaOwl in canada it's either 50cc or other and it's classified as a bicycle or it's over 50cc and it's a motorcycle. Not sure what your local laws are.
@jorgematos44765 жыл бұрын
My zeda 80cc dio reed valve motor is go 45 stock
@dangerousdoggo54655 жыл бұрын
@@jorgematos4476 your english is go poop
@zedee20003 жыл бұрын
A 212 4-stroke engine will stay together for a very very long time. unfortunately a two stroke will not and they will die of a very early death if you let them sit. And here's why the gasoline will rust the bearings over so much time sitting. and when you fire them up the bearing will go out causing early failure. Another problem of two strokes is being leaned out without enough oil. I like two strokes but I'd much rather have a 4-stroke any day on propane is the very best that way you don't have to deal with any carburetor problems at all, more dependable than any Honda, no gasoline in the oil, no carbon in the motor and on the spark plug at all. Propane engines will double the life expectancy of a 4-stroke, compared to a 4-stroke gasoline engine.
@angeldelgado13477 жыл бұрын
what does it top out at? top speed
@jefff1637 жыл бұрын
about 48mph
@gabebradley95427 жыл бұрын
whats the bike?
@BobTheBuilder2943 жыл бұрын
that left side needs a cover or something. That thing is going to snag your pants and ruin your day.
@velixare61997 жыл бұрын
What engine did you stick on that thing?
@jefff1637 жыл бұрын
its a 212 predator engine from harbor freight
@velixare61997 жыл бұрын
Is the speed shown in the video the top speed, or was that just showing it could? And if thats not the top speed what is?
@jefff1637 жыл бұрын
Velixare that was the top speed right before the chain came off so I'd say about 50 Mph
@velixare61997 жыл бұрын
Considering the engine is a 212cc, would this still be considered a motorized bike, or would it be classified as a motorcycle?