25. Set up L2TP/IPSec VPN on Windows Server 2019

[@torbjornrunesson3871]

Hi, if i follow the step i can connect to the VPN server but i dont have any internet connection. I have tried all thing that i can think about,, so please can you help?

[@MSFTWebCast]

Sorry for the mess. Solution: 1. Right-click on the existing VPN connection, and then select Properties. 2. Select the Networking tab, select Internet Protocol (TCP/IP Most probably IPv4) , and then select Properties. 3. Select Advanced, and then clear the Use default gateway on remote network check box. (Note: in this way routing is going through your PC for all , except the VPN Networks) 4. Click OK thrice. 5. Now connect to VPN server again and check the internet connection.

[@Giancarlo_Sforza]

​@@MSFTWebCast I had the same problem and it works now by doing this. Is there a way to configure this centrally on the VPN Server so that we don't have to do it on every single client machine? I have another problem, I can only connect to my VPN Server while being on the same local network, for some reason I cannot connect to my VPN Server over the internet even though I have enabled port forwarding. Any idea please?

[@melshad825]

Thank you for all your hard work. Keep up the good work, bro.

[@MSFTWebCast]

Thank You.

[@MuhammadWaqas-gr4gg]

dekhtedekhtekysekyahogaya................Pre-shared Key.......love this bro.....lol

[@BartMas]

Great content, very clear and understandable.

[@bicivelo]

These are the BEST videos. Thumbs up and subscribed. THANK YOU!!

[@irelialee8116]

Very clear and easy to understand, thank you very much.

[@sennaelemento]

nice video. please make more of these with a bigger pratice lab environment.

[@grey7593]

thank you very much, this is what I was looking for

[@DouglasGiovaniOechsler]

Hello! Great Video but, I am trying to config on pfsense to NAT. It cans make connection but after seconds the client says: Fail negotiation with security path on start with remote computer. I am trying a long time. First with pptp.... no works and now with L2TP

[@prakasht8764]

I am using a VPN server on Windows Server 2019 Datacenter Evaluation. The VPN is set up within the server, and I create VPN user accounts and passwords through the Computer Management tool. The setup uses the L2TP protocol with a pre-shared key for authentication. The VPN server is configured with a static address pool, allowing up to 30 private IPs to be assigned within a specified range. However, when one user connects to the VPN, and a second user attempts to connect, the first user is disconnected after a few seconds. I need solution for this?

[@Martin-ot7xj]

Hi there, at 09:44 ,how to change ip address of VPN server into the name server ?? i mean if we don't want give IP address to our client but instead, we want give the server name !! how to change or convert ip address to a name server ??? thnx

[@sarbabali]

Question: Can i do policy based ipsec between Juniper Srx 220 with windows server ?

[@yossicohen3895]

Please help, which ports exactly to open from the outside

[@NicholasDaniel11]

Love this channel!

[@MSFTWebCast]

Thank you!

[@asikin8228]

Hi, thankyou for shared this video. I have a problem when to step Active Directory Users & Computers. "To manage users and groups on this computer, use local user and group. To manage users, group & computer in a domain. Log on as s user with domain administration right" and My server work on workgroup (not domain). How to fix it? Can it work with workgroup?

[@MSFTWebCast]

If your server is in workgroup, you have to use Local Users and Groups snap-in (Use compmgmt.msc to access the snap-in) to create and manager users and group. Yes, it can work with workgroup.

[@davejkt1]

very clear, thank you. but, can you explain how to set up mikrotik , so the mikrotik can work with this windows server?

[@jomarescandor8633]

@MSFT Webcast. Thank you for the video! Did you know how to fix this problem? Remote Access and routing service failed to start because of the following error.Check the event log for more information The system cannot find the file specified.

[@kareemschultz]

Do you have a video demonstrating a remote user connecting to ad over VPN?

[@HaseebUrRehman-sb1zp]

I have vps windows server USA Location based. I want to set it as VPN and use THAT VPN in clinet pc in pakistan . Can use that vpn on andriod too?

[@yasharsobhani1294]

Hello my friend, how are you? Thanks for the good and practical videos. Please make a clip for (IKVe2) Thank you. good luck.

[@CMDRTurtle]

I agree

[@AnilKumar-ri6uw]

Hi, I have doubt, if we impliment ADDS and VPN server in same Machine is there any issue? or we need to have 2 different servers?

[@MSFTWebCast]

For small environment it is fine but with security risk. For medium to large it is not recommended.

[@chandrashekharsingh7252]

hi dear i want some Active directory questions, can you pls help my AD server is another, im Join AD on any laptop and Desktop use the AD static IP but the client wants to without VPN don't work the internet in AD user laptop anywhere 1-my DC install AD server and firewall 2-Client-side firewall and use the firewall VPN plz suggest

[@cyber_chrisp]

Can you do a video on IKEv2? Im confused on the certificate setup portion. Or can anyone point me to some help 🙏

[@awanwibisono]

is it possible to Connect to Internet over the VPN Server?

[@clashwithsmith2002]

Yes if u r using static ip from ISP

[@mohsinaligul8147]

@@clashwithsmith2002 as you know the static ip is costly you can use DDNS which will make your dynamic ip tp static IP without paying to you ISP

[@AlexH-ep1xy]

Hello How to setup VPN L2TP with Certificate in Windows Server and client side.

[@gilbertyegon2832]

Thanks for the video. I have followed step by step and successfully connected VPN to the server, but only worked on my local network. When I tried to connect via public IP address, the connection wasn't successful even after configuring pptp 1723 port forwarding on my router. Kindly assist

[@clashwithsmith2002]

U need a static ip windows server to connect through the Internet

[@stevenlawyer]

The problem is caused because in the default Windows configuration, IPsec won't work across network address translation (NAT). He didn't encounter this problem in the video because he's working in a test environment. To solve the problem, you need to add the following registry key on both the server and the Windows 10 client: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\PolicyAgent: AssumeUDPEncapsulationContextOnSendRule (DWord) with a value of 2.

[@mohsinaligul8147]

@@clashwithsmith2002 as you know the static ip is costly you can use DDNS which will make your dynamic ip tp static IP without paying to you ISP

[@Digitalrozgarmission]

Brother getting this error when i am connection windows 10 -- the network connection between your computer and the vpn server was interrupted this can be caused by a problem in the vpn tansmission and is commonly the result of internet

[@eegiischannel60]

Hello, could you help me to configure VPN in windows server 2019 ? please

[@KLNYC]

I got error 809. I tried methods in the net still no luck.. ugh

[@swapnilmashere9200]

Is IPSec vpn server possible with windows 10 or only possible on windows server?

[@MSFTWebCast]

You mean, does windows 10 supports IPsec connection with VPN server? The answer is yes. If you are asking whether windows 10 can act as an IPsec VPN server, the answer is NO.

[@swapnilmashere9200]

@@MSFTWebCast Thank you....

[@syedhussain904]

Hi Sir, Thank you very much for your excellent video. My client computer is successfully connected to VPN server (windows server 2019- hosted in Germany Office), however, internet is not running on client side machine. Can you please guide me how can i use internet on my client side machine as well as connected to VPN server.

[@MSFTWebCast]

Configure IP routing with NAT on VPN server.

[@syedhussain904]

@@MSFTWebCast thanks dear. I did and now all is working fantastic. You are bosssssssss

[@syedhussain904]

@@MSFTWebCast in your video you taught us about configuration of L2TP PSK. What is the difference between L2TP PSK and L2TP IPSec

[@diogchris]

I dont have internet after connected..why is that?

[@jplozer5813]

After I connect it to the VPN, the internet connection is no longer present. How to fix this??

[@MSFTWebCast]

You need to configure NAT on your VPN server.

[@ايوبالرشيدي-ه3ي]

hi how I can get the address not the ip for the server??

[@wilhelmtel794]

Hello please did you work out physically or logically 172.18.72.33 ? How can I fix if I lose internet connection on my VPN CLIENT after successfully connecting to VPN

[@BartikkCZ]

When you connect via VPN, your internet goes thru that VPN, in VPN setting you need to set IPv4 connection

[@wilhelmtel794]

@@BartikkCZ Thank you for the right tip.

[@moriscute]

@@BartikkCZ hi i have the same problem when im connected to vpn mi internet is not working, can you make a tutorial on how to fix this. Thank you

[@ayangangopadhyay4980]

Very nice video

[@Jvpereira87]

Hello, great content Thanks. Following along my vpn connection connects and I can pint the DNS fine, however once connected I can't access any webpage. As per the video, I can connect ok but clearly presents "no internet connection" anyone running same issue or solution to this please?

[@Maxime-Sparrow]

@MSFT WebCast Hi! thank you for video! I have been struggling with the problem of creating a server with l2tp for a very long time. I have static public ip, all port forwarding is configured, however, when I try to connect, it asks for a login/pass, and then after a minute of the "connecting" status, the process is interrupted with comment "...remote server is not responding". I have been unable to do this with win2017, win 2019 and win2022. PPTP worked sucessfully, but the standard "incoming connection" is not suitable for my tasks. I would be very grateful to anyone who can help me. Today I found that all android devices connect successfully. Check iPhones, Macs and linux... Windows from different PCs - unsuccessful...

[@MSFTWebCast]

Check the logs in event viewer on VPN server and also check logon event on Domain controller. Get the list of errors and let me know about it. If possible take screenshot and send an email. You can find my email address on channels about page.

[@wilhelmtel794]

how to config dns

[@ahmedsaad-lk2og]

ok

[@info1589]

HI,Thank you for this video , thats worked i got it , but i have a question about user login , with a username can login multi user in how can i change it , i want to allowed only 2 user in simultaneous allowed to login with one username , can you please help me to config this option , thank you again and have good day.

[@gunnarteutsch5456]

*

[@jaikumar8275]

Hi bro.. I need you Gmail account. Little clarification in subject msca. I gonna write on december.

[@Caracazz2]

Thanks, indian.

[@skefrank]

Ffs, cant understand yoooou !!!