Good work there Jim. Plus at the end you gave other options we use for removing damaged/broken shafts. I'm alway cautious on the amount of heat I use on the carbon crowned clubs as I've seem images of those tops popping off...the blame always falls on the club builder! I wrap the head in a damp towel to cover myself, even though, like you, I use as little heat as possible to get the job done :-)
@aaronmiller64554 жыл бұрын
Fabulous as usual. Thanks again. Always good to see you work
@hildashubby4 жыл бұрын
As always another great video Jim.
@donsmnc53194 жыл бұрын
This video reinforces why I quit repairing broken golf clubs a few years back and just take to repair shops like McGolf
@robtrudeau25234 жыл бұрын
Hi Jim, thanks for another great how to video. Thanks to you and all the great content that you produce I have been able to open my custom golf shop, RT Custom Golf and have already started to have ordered come in.
@mattrevilock58904 жыл бұрын
Awesome content. Great work Jim. B
@oceanroad15847 ай бұрын
Good video good help,ive two 3 woods with broken graphite shfTs it will give me something to do.
@FireConvoy884 жыл бұрын
Thanks for the tips on removal 👍
@jzpats19764 жыл бұрын
Awesome vid Jim.. recently subscribed to your channel and everything I have seen so far has reinforced my confidence as I work on my own clubs and perform club repairs. I have a question in regards to hosel depths on irons. Is it normal to see varying depths throughout a set? I noticed the 3 iron hosel depth on my TM Tour Preferred CB’s is deeper than the other clubs in the set. Thanks!
@McGolf4 жыл бұрын
Not usually, however a shallow hosel can allow for a slightly flight
@theimpaler50344 жыл бұрын
Question I got mizunos jpx 825 I had them since they came out on the market around 2012 I think I don't want upgrade to new clubs I love them so much after how many years should I replace the shafts and do steel shafts have a use by period example 5years or less before you need new steel shafts
@scotthucks79662 жыл бұрын
Just one question. On the Callaway head, why didn't you just unscrew the screw on bottom and take out adapter? Wouldn't the adapter with the shaft part come out together without all the heating and drilling? Thanks.
@SNeal59664 жыл бұрын
Why not just get a new adapter with the new shaft on the Callaway driver, seems much simpler? (pardon my ignorance, maybe those adapters are super expensive?)
@leogoku134 жыл бұрын
Where can I buy that hozel brush cleaner for drill?
@McGolf4 жыл бұрын
golfworks
@spanner41644 жыл бұрын
Do a video on the Wavey Wheel.
@ulster77174 жыл бұрын
Did you buy or make the edging on the side of your work bench that helps support clubs. I’m only a hobbiest but the number of times I have clubs falling this world be a great time saver.
@McGolf4 жыл бұрын
Got it from Lowe’s, it’s support material for the wavey roofing
@timnickert93084 жыл бұрын
Awesome videos! I’m a new subscriber and a new club builder and I had a question. How do you find the correct length when reshafting an iron? Do you just keep cutting small amounts on the new shaft while mocking it up in the head? Or is there a “time saver” way? Keep up the good work!! Thank you.
@McGolf4 жыл бұрын
Length is found during finding the flex. after the head is on the shaft measure the length you need and cut
@timnickert93084 жыл бұрын
McGolf Custom Clubs awesome. Thank you!
@brianfong39544 жыл бұрын
What would you do for iron with a sterl shaft that is broken right at the top of the hosel ?. Nothing to grab ?. Drill ? Easy out extractors ?.. Thznks
@McGolf4 жыл бұрын
Easy outs are the best option
@landygolfco.mikelandolt81854 жыл бұрын
Hey Jim can you still find Glanz Wach paste? Is the Menzerna GW16 replacing it? Thx
@garyyip88544 жыл бұрын
Hi Jim. I find the new callaway adaptors (original epic and newer) to have very fragile paint. Even a little bit of heat and the paint (and the numbers) flake off. Also find the same from TM from M5/6 and newer. Do you find this true as well? And if yes, any tips? Thank you :D
@McGolf4 жыл бұрын
No they can take heat about 40 to 50 sec and should remove easy. Outside of that then yes it can get dicey
@11golfnut114 жыл бұрын
As always thank you
@dbdors4 жыл бұрын
Do you find that some callaway adapters turn brown when you heat them? Or the paint/finish chips?
@McGolf4 жыл бұрын
If you get it too hot it will boil or change color
@The559Jeff4 жыл бұрын
Neutral bend point of shaft at top or bottom?
@McGolf4 жыл бұрын
if its neutral, I'm thinking its more towards the middle. I say that becasue bend points can be measured from the tip or from the butt, It depends on the company. however, I would say more towards the tip
@birdielizard4 жыл бұрын
Like the videos, but drop the music, my sound is up to hear what you say while working, and the music is really loud and annoying.