3 Phase Direct Online Starter DOL Wiring and Connections Explained

[@jonerasmus9399]

A tip that helped me as an appreciate was : split the circuit into two parts . 1 part control circuit and 2nd part is the main . Knowing that simplifies the wiring a bit more .

[@UnimportantAcc]

I wouldn't worry too much about meticulously learning the DOL. In the am2 you are provided with a wiring diagram, so it is very easy to see where the link cable is missing from.

[@GSHElectrical]

Thanks for the feedback 👍🏻

[@slelectricaleducation129]

kzbin.info/www/bejne/gXeWh5Rorq6Iga8

[@sunshine3187]

My dol wiring diagram today went L3-L2-L1 from left to right. Not L1-L2-L3.

[@montystelevision3238]

Yes to when a GSH alert pops up.

[@GSHElectrical]

😁👍🏻

[@montystelevision3238]

@@GSHElectrical Gaz. I’ve had an interesting email regarding the pulling of service fuses

[@Death88758]

I WISH you would do a continuity test on this from a three phase board,there is no such thing on KZbin😢

[@seanmcneill8899]

Very informative video on dol motor control. Thanks lads.

[@baaagudubala1363]

You are simply the best

[@GSHElectrical]

Thanks for the support 👍🏻

[@adamwright5553]

Just wondering could you post a photo of the single phase and the three phase DOL starter circuit diagram, would be handy to have when on site. Great video 👌

[@GSHElectrical]

Motors, Starters, Controls, Remote Stop Start - Single and 3 Phase kzbin.info/aero/PL2Ea5r9gxUUfv51Ld1UlNGR39rfFIExTU 👍🏻

[@slelectricaleducation129]

kzbin.info/www/bejne/gXeWh5Rorq6Iga8

[@joeldwarika8356]

Perfect.🎉🎉🎉tnx guys😊

[@EdijsUmanecs]

What is the benefit of using a contactor relay? Why not use 3 poles C32 Amper circuit breaker to use it as a switch for more simple schematics?

[@princejoseph1349]

Thank you guys ,this is really helping

[@laurabradley1857]

Hi - I love your videos and they have been super helpful in helping me prepare for my AM2s, however I managed to fail my Fault Finding. I know there is some description of a fault where the motor is 'juddering' or something similar but I cant for the life of me remember what the fault was or how to test and then rectify it. Can you help me with this? Thank you!

[@GSHElectrical]

Hi thanks for the lovely message. If a 3 phase motor was juddering it has lost one of it phases. Remember all faults on AM2S are found either visually or by dead testing. All the best and keep me updated 👍🏻

[@laurabradley1857]

​@@GSHElectrical I passed by the way!! Thank you! Loving life as a fully qualified spark now!

[@abdulseaforth6930]

@@GSHElectrical yes Gaz- I see. By losing one of the sizes, it’s out of balance so it won’t run so smoothly. It will make sense!

[@arjansingh4971]

How would u go on testing this using R1/R2??

[@just_saw_dust]

What about VFD. Lots of new IE2 & IE3 3ph motors are designed to be run from single phase supplies via inverters. I'd like to see this covered as a video with some reference to the way this works and is wired up with starters and remote controls.

[@benparsons5876]

Is there a connection from terminal 18 to 14?

[@GSHElectrical]

3 Phase Direct Online Starter DOL Wiring Diagram Connections Explained kzbin.info/www/bejne/o5S7qZuLlrqVb5Y

[@laurabradley1857]

Not specific to Motors but if the motor was turning the wrong way, this is the result of 2 phases being crossed... is this Polarity or is polarity only when the Neutral is involved? Would I just say crossed phases/conductors? I think the terminology I used was wrong last time & I don't want to make the same mistakes!

[@toughshoe6408]

Do you install a single phase motor on 3 phase in your am2?

[@GSHElectrical]

3 phase

[@seanpritchard2650]

How would you wire a 415v coil with a pressure switch

[@tylerarmitage1476]

credit boys very helpful.

[@GSHElectrical]

Thanks 👍🏻

[@brianhewitt8618]

👌

[@ELECTRICLIFE4U]

👍👍👍👍👍