Hope this video helps! Let me know if you have any questions.
@asianturttle1737 Жыл бұрын
When you had that problem did it feel like your clutch disengage ? At 3700 rpm?
@adamgalindo Жыл бұрын
Didn’t have my foot on the clutch. It would be when I was accelerating and it’d feel like it lost power
@MrAnxious11 ай бұрын
My throttle body was insanely bad. Like thick thick coating. I changed my intake filters too and My car is driving so much better. It felt chocked up before. Thank you brodie 🙏🏽
@franciscoreyes7719 ай бұрын
Yo same mine was black and had never been cleaned
@PapaHerb-og4bc19 күн бұрын
Thank you so much brother, saved me a trip to the mechanic. The limp mode went away and my car idles back to normal 🐐
@nelsonlind87832 ай бұрын
Wow, awesome clip! Had to clean throttle bodies and MAF since my 2010 370z roadster was running rough. I can guarantee they were never cleaned by previous owner because when I started cleaning, they were both super dirty with crud. I wasn't quite sure why the idle was so high after I cleaned them until I saw your clip...didn't know I had to do the steps you provided to re-learn throttle bodies and pedals to get it back where is should be idling. My Z car is running great thanks to your instructions. Again, outstanding instructions, thanks!
@adamgalindo2 ай бұрын
Glad I could help!
@mmkoygarage5 ай бұрын
Thanks a bunch bro, this is definitely the best guide for VQ37HR owners looking to clean throttle body and MAF Sensor and gain maybe 5hp lol. The recalibration took me a while but im lowk slow, I have a G37x sedan btw works for any Nissan/infiniti with the VQ37HR
@heberlara60797 ай бұрын
Never touch/move the throttle plate with your fingers.. have something or someone step on the gas (not with car on of course) as it is electronically operated and it might mess it and you will have to re-program your car. Learned the hard way.
@AyoDave6024 ай бұрын
Is this true? Did this mess up the Z’s idling or anything wierd after cleaning throttle bodies??
@heberlara60794 ай бұрын
@@AyoDave602 for any electronically operated throttle body, yes. If is not electronically, you can move it around.
@adamgalindo4 ай бұрын
Nothing happened to mine
@obender663 ай бұрын
Done that multiple times on G35 and 370Z-no issues.
@heberlara60793 ай бұрын
@@obender66 good then is Not electronically operated 🤷🏻♂️
@robnemily4 ай бұрын
Thank you! This was helpful. My G37 6MT has 78K miles and my driver's side resonator had broken - causing it to run too rich and throttle rpm at 2300. I repaired the resonator, (JB WELD) and cleaned the MAS and the throttle body. Huge improvement - this breathed new life into it. acceleration is smooth and linear again. I have way better throttle response than I did even before the resonator housing cracked.
@1EVE1X8 ай бұрын
bro i just pressed up down left right L1 L2 R1 R2 and now it becomes an automatic and never stalls. thank you for the video
@adamgalindo7 ай бұрын
😂
@joeyholestine1505 Жыл бұрын
Just got a 2012 Z and your videos are answering so many of my questions and concerns. Keep it up man bc you put out good quality videos for being a small channel rn. Hope one day I can say I’ve been here from 1k subs🫶
@adamgalindo Жыл бұрын
Congrats on the Z! Really appreciate that man 🙏
@JEzPz3 ай бұрын
SWEET! Thank you bro!
@andrescastaneda8983 Жыл бұрын
Thanks bro a super good video very helpful
@Zax_130310 ай бұрын
quality video keep em comming
@jeremymaffei403411 ай бұрын
Great educational vid‼️
@brolsonmusicАй бұрын
Your car idles high at could start and that is normal! Mine does and then if you sit for 30 seconds it drops down. It helps warm it up faster.
@dllouu Жыл бұрын
Thank you bro!!
@richardblends8647 Жыл бұрын
i recently did this since i had a check engine light/service light 💡 did everything you said in the video but my car seems to idle back to normal without resetting the factory .. i’m at 600-700 idle car runs amazing since the cleaning definitely needed that
@Bravo-ro4zb8 ай бұрын
What code was ur check engine thanks
@Ceeski-bb6wy7 ай бұрын
what code did it bring up
@arvindabhola62516 ай бұрын
Hey bro, do you know what code came up? Mine was P0507
@gsteel982 ай бұрын
My rpms go high like normal but it goes much slower, got a pending code for p0101. (2013 g37x) Hoping i just gotta clean the maf sensors for now. Gonna clean the throttle body anotherday
@AyoDave6024 ай бұрын
When you cleaned your throttle bodies did you notice anything wierd with idling? Throttle response ?
@SquishEESpark7 ай бұрын
If your car is like mine and the bolts won’t undo on the strut bar, you can remove the tubing etc. to access the throttle body without taking the strut bar off.
@matthewlunsford2904Ай бұрын
I’m showing code p1016 p100a and p100b, everytime I turn my car off it makes that robotic click, whether the ignition is on or just the car. Can any one think of any reason or help me out
@Bruno-bw1bh2 ай бұрын
So I did this but the SES light was blinking fast and it still was on what shows I do??
@9smaccs3 ай бұрын
Does it work on 2007 g35 it’s a hr same body style and dn same parts all around as the 37 except the motor but I wasn’t cleaning my throttle bodies I was replacing them
@toobreezy3112 Жыл бұрын
Nice video!! Do you plan on getting any performance mods for the z?
@adamgalindo Жыл бұрын
I do plan on it eventually but most things are just out of the budget right now, unfortunately. The main thing I want is an oil cooler
@NeffKid99 Жыл бұрын
I did everything and it worked but then when I started driving there’s like a throttle lag when I’m trying to gas it. Any ideas why that’s happening?
@adamgalindo Жыл бұрын
Not exactly but maybe take a look to make sure all the couplers are tightened and everything is tight
@3inchmafia Жыл бұрын
I have an 09 370 with high idling, and I’ve had the p300 code, swapped the plugs and coils, checked for vacuum leaks and cleaned the mafs, this is my last hope lol I’m worried about the relearning process looks tricky
@adamgalindo Жыл бұрын
It’s simpler than it seems. Feels like you’re doing cheat codes in a video game lol
@TheSaint0358 Жыл бұрын
Did it just randomly happen one day after you started it up? Does it idle around 1k-1.2k rpm? I also have an 09 370z
@bernerporres3906 Жыл бұрын
Did you end up figuring it out? I’ve also on the same boat at you & have swapped the same stuff you swapped and still haven’t figured it out. However yet to try this! We’re you able to fix it?? Please lmk!
@jordanbarnhill3511 ай бұрын
I have the same code and am trouble shooting the same problems, what was the resolution for you?
@jordanbarnhill3511 ай бұрын
@@bernerporres3906 I have the same code and am trouble shooting the same problems, what was the resolution for you?
@veasnayong3456Ай бұрын
Did it fix the limp mode?
@adamgalindoАй бұрын
Yes
@Ghostboi998 ай бұрын
Why not take off the whole thing to do both sides front and back since back has all that dirt
@freddypacay71016 ай бұрын
I did it followed ur instructions but I have a question after the 1st start after the reset the speedometer was going up and down once I did a 2nd start it did but way less very little should I be worried?
@adamgalindo6 ай бұрын
What does it idle at now?
@freddypacay71016 ай бұрын
@@adamgalindo600-700ish
@shontiaorr89797 ай бұрын
🔥
@somebodyelse9696 Жыл бұрын
Will this work for a Q50 as well?
@cynicalproductions606010 ай бұрын
yes
@lithalobadi25019 ай бұрын
was there any solution being put on the toothbrush to clean the throttle body or were u just rubbing the dirt off with the bare toothbrush
@adamgalindo9 ай бұрын
You could wet the brush a little bit but no I did not add anything
@lowkeyg35305 ай бұрын
Do you have to disconnect the battery to do this process ?
@adamgalindo5 ай бұрын
Yes you should
@alexanderamayaportillo82556 ай бұрын
I followed your exact steps but I didn’t hear my throttle body’s reset? Help please!
@adamgalindo6 ай бұрын
What is your car idling at?
@CoolDansta Жыл бұрын
My 15 Nismo SES light came on and I've replaced the MAF cleaned the Stillen air filters and disconnected battery but the light keeps coming on throwing the codes for MAF P0101 and P010B any idea what else it can be? At first I tried cleaning the original MAF but light kept coming on so I got new MAF for both sides and light keeps coming on
@adamgalindo Жыл бұрын
Have you tried cleaning the throttle bodies? Also make sure all the couplers are on and tight properly
@north_ak_3258 ай бұрын
Can I do this and avoid the resetting because I have a tune on my 2009 370z but idk what or who did the tune because I bought it like that I just got a code pop up saying P1421 which is a cold start code and I think my best solution is to clean the throttle bodies instead of replacing them because I don’t think the previous owners cleaned them
@adamgalindo7 ай бұрын
It could affect your idle if you don’t end up resetting it. I would contact the tuner who tuned the car if you know to see if it’s safe to reset
@Vr30_Oscar Жыл бұрын
To clean the body throttle can I use a wire brush or should I stick with the toothbrush
@adamgalindo Жыл бұрын
Stick with a toothbrush, you don’t want the wire brush scratching the surfaces
@zhang3104 Жыл бұрын
Recently my car has code p1239, whichI think is a throttle body problem. I wanna try to clean and reset it, but I have admin tune, and I was wondering if I do the relearn and reset, will that mess up my tune?
@adamgalindo Жыл бұрын
It honestly might but not too sure. I would ask your tuner if you can
@cartercarstensen374 Жыл бұрын
did you ever figure it out? i have the same code and my car is also admin tuned but i don’t know if it would mess up the tune
@zhang310411 ай бұрын
I emailed the admin tune, and they said it was fine and wouldn't mess up anything; that code just popped out randomly. My car drives fine, so I did not clean the throttle body.@@cartercarstensen374
@sxnchez34 Жыл бұрын
What do you mean by 149° and above?? I did a cold start but how am I suppose to know when 149°is. Like my oil gauge? Or the engine temperature
@TomAgullo Жыл бұрын
I went by the oil gauge and it worked
@adamgalindo Жыл бұрын
Yes the oil gauge on your dash
@Smithant005 Жыл бұрын
I’ve tried the last step of pushing pedal to floor and waiting for service engine light to blink.. but it won’t work. Any suggestions?
@adamgalindo Жыл бұрын
Make sure car is at operating temps and battery is strong. Turn off ac and radio to reduce energy usage. If you’re following that and the rest of the steps in the vid then it should work. Maybe your timing is off? Lmk how it goes
@Wdpmiguel8 ай бұрын
@@adamgalindosame thing I tried different timing still didn’t work
@gods1hell1spawn10011 Жыл бұрын
My throttle body shat the bed and im replacing it. Thanks for the vid! You think if I'd of cleaned them it wouldn't of died on me? Or that's something else .. im at 200k km
@adamgalindo Жыл бұрын
It’s possible if no one’s ever cleaned it before. What exactly broke?
@gods1hell1spawn10011 Жыл бұрын
@Adam Galindo It was the sensor idk how. I have tekada stock diameter intakes, waiting to tune in good weather
@lowlifespore899310 ай бұрын
My car is in limp mode with codes p2135 and p1239 🤦🏽♂️ and p1705
@jugg637 Жыл бұрын
i want to try this for my g but im scared my tune might mess up the idle relearn
@adamgalindo Жыл бұрын
Yea I would probably avoid it. If you can ask your tuner if it’s safe to do
@jugg637 Жыл бұрын
@@adamgalindo yeah ill just bring it to my tuner so he can do it, thankfully they do maintenance on them too
@JulianTuttobene4 ай бұрын
My car dies immediately after starting it could this be the problem
@adamgalindo4 ай бұрын
Not exactly sure but wouldn’t hurt to try
@TheMarkShenouda Жыл бұрын
So how do you know what the Engine coolant temperature is?
@TheMarkShenouda Жыл бұрын
To add to that, I have a 2009 370z and the service engine soon light doesn't appear. I don't know if I can see one.
@adamgalindo Жыл бұрын
On the bottom section of where your fuel gauge is
@adamgalindo Жыл бұрын
That’s strange, the light may have gone out. Maybe try following all the steps still and see if it works. Just try to time it good since you won’t have the light indication
@kuro9865 Жыл бұрын
Is this work for 2009 model ?
@adamgalindo Жыл бұрын
Yes it should
@fernandoherrera7628 Жыл бұрын
Did it fix your issue ?
@adamgalindo Жыл бұрын
It did 👍
@Nexushuggah Жыл бұрын
Messaged you on fb bro. Thanks!
@adamgalindo Жыл бұрын
Didn’t see it. Dm me on ig instead @adamgalindo_
@nathanielmoore91326 ай бұрын
After cleaning my TBs and mafs, I now have random misfires and codes are cylinder 1 misfire, and both p0101c and b, which are mafs
@jusindominguez28716 ай бұрын
Did you do the factory reset?
@ksich8142 Жыл бұрын
My throttle bodies make noise every time I turn the car off
@adamgalindo Жыл бұрын
That’s normal
@LongLiveIsrael7426 ай бұрын
Yo im hella fucking new to all this, what are the tools you are talking about aha?
@966XXXXXXXXX4 ай бұрын
fully depress the accelerator peda Wait 20 seconds and Fully release the accelerator pedal within 3 seconds after the MIL turns ON (((((((((( NOT RUN in wait 3 seconds in stop MIL ) and ON