How To: 350Z 75mm Throttle Body Install

[@jackfurniss8751]

Do a video with pathfinder coolant mod.

[@primosgangentertainment6729]

Can yah do a video on replacing all the hoses plss 🙏🏾

[@benny6712]

Hopefully you guys cleaned that corroded negative battery terminal

[@pedronaranjito]

I'd really like to see a video about chain tensioner, using the little window

[@kareemgibson6984]

Wish you guys would do the upper oil pan on the 350z since a lot of people seems to crack them trying to screw in the oil sensor like i just did. (This sucks)

[@toddhall5939]

So if you do the z1 plenum spacer, the z1 75mm throttle body and the z1 mspec cold air intake, you don’t have to do any kind of tuning?

[@Sigue24]

Would this require me to retune or would it be ok due to the small change in diameter?

[@eladiorosa4970]

Do you sell the throttle body adapter only?

[@TRACKMKIII]

No side by side comparison? No before and after dyno numbers?

[@JeffMisa]

What if you did the video on a G35 with the coolant lines running to the throttle body???💡

[@ericortiz5042]

Would this work buying 2 and putting it on a 370z?

[@tanyabennett8431]

When you change it to the 75mm throttle body do you have to change injectors and lines to match or does it matter

[@djrevise]

is this better than plenum spacer?

[@angelangel6154]

Why does this come up lol ??? When I just stripped the top left Allen screw kms.

[@jayvaz9583]

Silicon hose name n part number?

[@Lolatyou332]

Is there even a reason to increase the throttle body size with the same plenum as stock, even with the plenum spacer? I feel like it probably won't really improve performance much at all. I guess I'd like to see a dyno on if they actually improve performance without other modifications on the car.

[@sneakypete2656]

From what research I've done on this for my charger and g37 which i did get 75mm throttle bodies for the gains with just the throttle bodies aren't much. I did the upper and lower manifold and the z1 3 inch intakes at the same time so i don't know how much they helped specifically, company claimed 10 whp, they cost over $600 though. They were also a pain in the ass to fit in especially with the 3 inch intakes. Personally if i could go back i probably would have put that $650 elsewhere but I'm not unhappy with them, they look good and they do help some I'm sure, especially with the bigger intakes.

[@sneakypete2656]

Paired with forced induction they'd do a lot better.

[@Lolatyou332]

​@@sneakypete2656 It's just that the diameter is going to be limited by the plenum and intakes anyway, so if you don't upgrade the plenum and the intake manifold it's really not actually adding much diameter. I think with doing the upper manifold and air intake (larger pipes) it likely would help a bit assuming there aren't flow issues exhaust wise, but really think it probably should be one of the last upgrades done IMO after everything else is good.

[@joshuasutton4043]

Good info

[@gatorgaming8312]

Where 350z supercharger?!?!?

[@Nejinissan440]

Does the oem intake hose fit on this throttle body?

[@codyoneill6091]

No. You need the adapter that goes from 75mm throttle body to stock intake

[@Nejinissan440]

@@codyoneill6091 thank you

[@TGR972]

👍🏽

[@auxdog]

I hate cali for making this illegal to order

[@TheDrAkira]

I came here looking for the correct position of the throttle body gasket because I really don't know which way to put it in. Nobody shows how I was hopping for the good guys from Z1 that I usually throw happily money in parts to to maybe show me that but... Nop...🥲🥲🥲