You don't even have to empty the vat for cleaning. I just stick a failed print in the corner of the vat, hit the cleaning button, and use the failed print as a handle to peel it off.
@3DJake_Official8 ай бұрын
oh that's a cool idea, I gotta try that!
@christopherwilson73347 ай бұрын
thats what I do
@Russianbreadguy5 ай бұрын
I have left in there for months and a stir and vat clean and it’s good to go again.
@SilvanKofmehl8 ай бұрын
every resin printer has this cleaning feature. simply do a lamp test, for that the lcd is off and all the light goes to the vat.
@shawnsustrich79813 ай бұрын
Im stoked. Just upgraded to the m5s pro from my mono x 4k . Bigger, more detailed, quicker if I want to spend the money on fast resin.
@Kellykiller-mj2bn7 ай бұрын
hey, Thanks for the great review! I'm still new to 3D printing and have been considering for some time whether (and which) resin printer I should buy. I've been wavering between the Elegoo Saturn 3 Ultra 12K and the Anycubic Photon Mono M5s Pro and I can't make up my mind. The most important issue is the odour. We are an office with a shop and I want to install the printer one floor down by the window (just a staircase, there's no door or anything). Which one can I use better without being unable to work on the PC? So how well do the air filters work? You can also connect a larger extraction station to the Elegoo Saturn 3 Ultra 12K if the two small filters are not sufficient. Is this also possible with the Anycubic? Or is it necessary?
@3DJake_Official7 ай бұрын
When a printer's cover is closed there is not much odour escaping but the best printer here would be the Saturn 3 Ultra as it can support two air filters however if you are putting it next to an open window, it could be better to get the M5s Pro because of the heater, really depends on how cold your printer will get if it is exposed to wind. Unfortunately, the M5s Pro does not support extraction fans, you would have to cut through the acrylic cover. If you keep your printer in a non-occupied area it is not that necessary.
@DorianLust8 ай бұрын
I like my mono 4k, I never level it, never clean the build plate, nothing! Just rip off the print put it back and print again the next week. Never a single failure after 30 prints, and I don't even use most of the supports it recommends. A+ so far. Thinking of upgrading if all of this fancy stuff is any good, I almost don't trust the added features to be as good as what I have.
@Adrianv19815 ай бұрын
im so frustrated with my ender3 dude, i hate leveling it every fucking print. Hows life on the resin side?
@DorianLust5 ай бұрын
@adrianvalverde1636 the down side is curing and cleaning. You need gloves and a good mask, and it's easy to make a mess or cure resin by accident. So it's not all good. But the quality and surface finish are really nice.
@wsawsawsa3 ай бұрын
Thanks for your review! I bought this printer and it comes with 4 bottles of high-speed resin. You say that the recommended settings for it are 0.05 mm layer height.. I would like to achieve printing at a layer height of 0.01mm (10 microns). Theoretically, this is possible. But is it possible to achieve this with high-speed resin? Can I lower the printing speed? If not, which resin would you recommend for a 10-microns layer?
@3DJake_Official3 ай бұрын
It should totally be possible with a high speed resin. The only major thing you would need to change is the exposure times, they would need to be lowered. Changing the lift/retract speed shouldn't be an absolute necessity, I would try a test with just exposure time reduction and see how it goes.
@wsawsawsa3 ай бұрын
@@3DJake_Official Thank you, i will try
@marcelschulte-pelkum73717 ай бұрын
Is the "Air Mate" (Purifier) removable and do I have to charge it. Or does he get power from the printer? Thanks 😊
@feresthergomez87946 ай бұрын
Hello, could you help me please, I am looking at these machines for dental laboratory use, which one would you recommend, if they are compatible with Chitubox. 1- Anycubic Photon D2. 2- Anycubic Photon M5S Pro 14k. 3- Anycubic Photon M5S 12K. 4-Saturn 3 Ultra 12K Elegoo. 5-Mars 4 Max 6K Elegoo. Those are the ones I've seen or which one would be better. Please help. Greetings and thanks.
@3DJake_Official6 ай бұрын
Generally, we would recommend the highest resolution for dental applications but I would also take a look at which resins you are using and how well they perform on these printers. But I wouldn't recommend the D2 or the Mars 4 Max, the resolution is just too low. Chitubox Basic 2.0 now has recommended settings for certain printers with certain resins, I would give that a check and try slicing them with it, I heard the conversion process to an Anycubic format can be quite slow in which case it might be less irritating to use an Elegoo printer or another brand.
@feresthergomez87946 ай бұрын
wao muchas gracias@@3DJake_Official
@feresthergomez87946 ай бұрын
These machines are available in my country, which one would you recommend please? Saturn 3 Ultra 12K Elegoo Mars 4 Max 6K Elegoo Anycubic Photon M5S Pro 14k@@3DJake_Official
@3DJake_Official6 ай бұрын
@@feresthergomez8794 I preferred the M5S Pro because of the autolevelling and heater control
@feresthergomez87946 ай бұрын
@@3DJake_Official super... thank you very much
@TheAllseeingAi2 ай бұрын
Thank you for the review! I am torn between the mars 5 ultra and this Mono m5s pro. Could you help me by answering this, do you have to print at the 0.1mm thickness on fast print or can you choose a slower print and mm such as 0.5mm or even lower?
@3DJake_Official2 ай бұрын
Do you mean 0.05? or 0.5? You can print at 0.5 or lower but it will be slower so the 150mm/h speed wouldn't be possible under 0.1
@politicalpolarbear8 ай бұрын
I wish companies had the flip-up lids that others are starting to use. some of the features are interesting. might have to check it out when I finally upgrade.
@im10668 ай бұрын
It has a leveling screw set, they are hidden under stickers on the side of the head. I had to level my "self leveling" M5s...
@highlander55216 ай бұрын
Wie sieht das mit dem Kabel aus? Gibt es da eine Ausparung hinten für das Kabel?
@3DJake_Official6 ай бұрын
Unser Gerät war ein Testgerät und hatte keine Aussparung - Serienmodelle haben jedoch eine Aussparung
@ArabVlogger8 ай бұрын
Is it good for jewellery like Turkish jewellry do you prefer and is this support Proto speed sharp resin
@Shai4568 ай бұрын
How noisy is this printer? I have Mono SE which is great but I was thinking about replacement. Unfortunately other printers (for example Anycubic 6k) are much louder.
@3DJake_Official8 ай бұрын
It's relatively quiet, honestly, I have never questioned if it is too loud. Pretty similar to most resin printers.
@carloschuman91504 ай бұрын
cual es mejor la saturn ultra 3 o m5s pro?
@tristanc22717 ай бұрын
I'm legit thinking of getting this as my first printer, but maybe you can answer some questions. Can you pause the printer mid print? (to top off resin) Does this printer have anti aliasing? And is there a better printer out there that has a decent build volume and under 25 micron resolution?
@xConundrumx7 ай бұрын
If I understand correctly the printer warns you in advance if you do not have enough resin (to start). It has resin detection too. Mind you I am still waiting for mine so this is just from other reviews. The vat is quite large too. Replenishing mid print also is possible and the printer will even stop for you and tell you to add more. As for your other question I will have to pass on the answer.
@Jregidor19619 ай бұрын
un gran avance lo del calentador, se han dado cuenta de la necesidad que tenemos en climas fríos para poder imprimir con calidad, en gerneral parece una gran maquina
@luki3846 ай бұрын
Hey, how does this machine handle "Water-Wash Resin+"
@3DJake_Official5 ай бұрын
Haven't tested it but it really shouldn't be a problem at all
@cattivik66297 ай бұрын
How is the print quality compared to the Saturn 3 Ultra? I know it is a difficult comparison as it would require the same ACF film & temperature to have a 100% realistic comparison, but I would like to have your opinion. Thanks!
@3DJake_Official7 ай бұрын
I wish I could give you a better answer than this but honestly I don't notice much of a difference :/
@bladiblu38268 ай бұрын
Many thanks for the details. Could you please share the link for the bottle funnel? Many thanks!
@3DJake_Official8 ай бұрын
Whoops! Here it is www.printables.com/model/457782-screw-on-funnel-for-3djake-resin-bottles-500ml-and
@AlexPortRacing9 ай бұрын
How effective is the air filter at removing any smell?
@3DJake_Official9 ай бұрын
I haven't noticed much difference between it and competing printers
@BrickBazooka8 ай бұрын
you will have to vent out resin air either way
@IDOLA1496 ай бұрын
Dave? Bah, i'll wait for the next model, Keith
@Raainmaker6 ай бұрын
or their premium flagship Tony
@wonny36248 ай бұрын
Which one looks better compared to saturn 3 ultra?
@BrickBazooka8 ай бұрын
saturn3ultra looks better, Linux OS and the ips screen is nice. but featurewise this m5spro is way better. elegoo needs to come up with saturn3ultrapro
@dirtysaint53248 ай бұрын
I’m returning mine. Build plate came warped, they aren’t offered anywhere, and support won’t get back to me until the 17th due to the holiday. Three weeks, not one success.
@BrickBazooka8 ай бұрын
@@dirtysaint5324 which one are u returning bro?
@wonny36248 ай бұрын
@@dirtysaint5324 what is your one? saturn? m5s pro?
@rowndo7 ай бұрын
@@dirtysaint5324 yep which one are you talking about?
@spedi67219 ай бұрын
I'll support your idea with "Dave" 😅
@ryangamble5092 ай бұрын
Q: Would this be a good 1st 3d printer for a teenager who is very smart!
@3DJake_Official2 ай бұрын
I wouldn't really recommend a resin printer for children. An FDM printer would be better but even then only with appropriate supervision.
@vizzwizz8 ай бұрын
never showed it action. 'great review'
@sejason47249 ай бұрын
Thanks for the review :)
@warmup17059 ай бұрын
Would this be a good first resin printer to someone w 3+ years of fdm printing experience, now has a p1s and wants to get into resin printing for high detail stuff w minimal hassle?
@3DJake_Official9 ай бұрын
Yep I think it would be great!
@jeretthauersperger64338 ай бұрын
quick question, does the m5s pro and the m5s use the same vats? figured i would ask someone who has the unit in front of them lol
@3DJake_Official8 ай бұрын
I have the Pro in front of me but actually not the non-pro so I'll get back to you on that but I think it is the same.
@ArabVlogger8 ай бұрын
And is it better than Phrozen sonic mighty 8k 3d printer please do reply thanks
@3DJake_Official8 ай бұрын
Not really that familiar with Turkish jewellery but I would think so. In terms of resolution it is better yes.
@miguellopez33928 ай бұрын
Has better resolution but mighty 8k uses a different lighting method that gives it over 90% light uniformity vs up to 85% on the m5s pro, this makes the pixels sharper and makes light over the entire screen more uniform, so it's better for mass printing where quality doesn't drop if you put things at the edge of the screen.
@leonkernan8 ай бұрын
Dave sounds cool.
@teabagNBG8 ай бұрын
anycubic dave would be a awesome name hahahaha
@jasonvil92706 ай бұрын
Scammers!!!!!
@theNikonGuy4 ай бұрын
What sort of muppet would remove the vat when the build plate is still attached and dripping? Ohhh.... you would!