She was lucky enough to turn the antenna she made into an anode (+) that was extended in contact through the original antenna without the negative (-) wires.
@ramkrishnarao88103 жыл бұрын
To improve single and consistency you need to separate receiver disk from the reflector.
@rejulalalat27403 жыл бұрын
Need to isolate with insulators
@brajeshsahu91212 жыл бұрын
What is reciever sir what do you mean sir?
@djouadibrah2877 Жыл бұрын
@@brajeshsahu9121 ithink he mean director disks
@justinmadden30810 ай бұрын
U need to isolate the driven element from the other discs otherwise ur antenna will perform horrible and you can damage your router
@easystockoptions40672 жыл бұрын
What frequency is this tuned for? Where can I find calculations for other frequencies?
@IsmaelDomingues-og3tv6 ай бұрын
Muy buenos muy buenos
@CHOCOFF213 ай бұрын
Te funcionó?
@justinmadden30810 ай бұрын
Wow then cable runs are gona kill any gains , use lmr400 not that cheap coaxial run plus your using satellite 75 ohm connectors ur gona have a mismatch as it all needs to be 50 ohm
@robertoroca6234 Жыл бұрын
No mostras el momento de conectar los cables a la antena, y que es elemental para hacerlo bien
@asankac93173 жыл бұрын
Are distance between to plates not changed in different frequency???
@ijazkhanniazi8002 жыл бұрын
Distance between plate varies according to required frequency
@robbw27602 жыл бұрын
Can u use a omnidirectional tv outside and a flat panel inside connected together both powered for a booster
@hoatsoomro74732 жыл бұрын
Good
@pauljacques41572 жыл бұрын
Bonjour, pour 900Mhz et 2100Mhz ce serait quel diamètre est distance ? Merci
@4sp3ro2 жыл бұрын
why ground ifit not be connected?? more meters of coaxial just loss signal.
@3dart4973 жыл бұрын
Zo'r 👍🙂🙂
@1001Ideas3 жыл бұрын
Thanks
@luisguzman184127 күн бұрын
❤❤
@AbduqahhorNematov3 жыл бұрын
🔥🔥🔥🔥
@rebelmusicbeats2 ай бұрын
Que es y cómo se llama lo que conectas a la antena que le da la conexión al teléfono
@muraddawod83313 жыл бұрын
RUBISH, THIS IS A BAD EXAMPLE OF BUILDING AN ANTENNA, FIRST DRIVE ELEMENT SHOULD BE SEPARATED FROM THE RECEIVER DISK AND REFLECTOR, SECOND IN CONNECTOR YOU LOST GROUND WHY?
@samuelhendrawsinaga10642 жыл бұрын
You comment is rubish antenna too. No solution just comment is zero. Big LOL
@dazzer_2 жыл бұрын
@@samuelhendrawsinaga1064 Read again. He needs to separate the receiver disk and reflector. That is the solution. Bigger LOL
@nanik63128 ай бұрын
@@samuelhendrawsinaga1064 dumbass
@vasusiripireddy12903 жыл бұрын
Is this really helps to improve signal ?? I hope this is loll😀😀
@afiqevo272 ай бұрын
that was poor connection because no ground connection ... is should have for outer shield cable for gnd connection and better performance
@arresofficial29192 жыл бұрын
is this really working to a dead spots area?
@Bangcikal9982 жыл бұрын
Hebatka . Solusi dong g gimana cara nangkap signale WiFi orbit pake antena Yagi xteme
@ngovanngocngo38722 жыл бұрын
b593u-12 can you use it?
@ijazkhanniazi8002 жыл бұрын
It shouldn't work properly as 2nd disk is not isolated from rod
@shyedkhan9347 Жыл бұрын
how to isolated the 2nd disk sir , is it by making a big hole, isolated from rod
@ijazkhanniazi800 Жыл бұрын
@@shyedkhan9347 no cover rod with tape or plastic
@ayritomtv86303 жыл бұрын
👍👍👍👍😳
@1001Ideas3 жыл бұрын
😊
@hard_talk_bd Жыл бұрын
U are checking @ wifi speed at the screen
@NA-nr4mk Жыл бұрын
سلام وقت بخیر .به زبانه فارسی لطفا ترجمه کنید
@syarmrock77012 жыл бұрын
This way for 3g only
@Hype0602 жыл бұрын
there congested
@diamant84212 жыл бұрын
download 33.11 Mbps
@bosya63613 жыл бұрын
Факат центральный жилани пайка килдиз оплетканихам пайка килиш керак ундан кейн сиз ясаган схема буйча антенна тугри эмас
@1001Ideas3 жыл бұрын
Лекин ишлади сигнал кучайди
@Thejackal9713 жыл бұрын
Which material did you use?
@dumerai50453 жыл бұрын
Ya I want to know too
@samikhanniazi1641 Жыл бұрын
kis matrel sy baya hai
@cynthiamaurents1619 Жыл бұрын
Ini model antena induksi ya kak
@adamczarny10792 жыл бұрын
0
@Michael-1313Ай бұрын
No se entiende !
@ijazkhanniazi8002 жыл бұрын
Please tell me its working frequency range
@idsellggame57683 жыл бұрын
What kind of signal cable is it?
@1001Ideas3 жыл бұрын
this is a TV antenna cable
@christianhr7005 Жыл бұрын
Amigo! Ese material es hoja e lata? Cuánto debe ser el grosor? Se puede hacer con laminas de aluminio o laminas de cobre? Hay alguna antena del mismo modelo pero que trabaje en las bandas 900/1800/2100 mhz? En dado caso de tener que fabricarlas por separado, se podrían tener 3 antenas en el mismo mástil? Muchas gracias, ha Sido de mucha ayuda su vídeo (y)