400w 15A DC-DC step up boost converter 10-60 volts

[@JacobBitner]

Thats a beautiful meter!

[@tech.5137]

0:52 + output terminal and heat sink on one side are connected. The heat sink on the opposite side is connected to the ground side. When the maximum voltage is generated, high voltage is applied to both heat sinks. Risk of electric shock and fire. 0:52 +出力端子と片側の放熱板が接続されている。 反対側の放熱板はアース側に接続されている。 最高電圧が発生してる時は両方の放熱板に高電圧が掛かっている。 感電と火災の危険がある。

[@techno-diathesivagelisilio940]

Thank you sir, For your kind highlighting of the situation. For dangers which can happen in these procedures! Obliged!

[@wsj1983]

Hi! I'm making a small motorhome setup, and I bought a step up like this to use my laptop without a inverter. My laptop has a 19V, - 7,89A adaptor. So to switch the amperage in the step up trimpot I guess I will need to try with another charge (like a light bulb), and after having it right then I can stick my laptop on it. Am I right? Or could I do the amperage trimpot thing - having the right tension already of course - direct with the laptop on it? tnx for your video?

[@techno-diathesivagelisilio940]

As you have seen in the video the power supply was 12 volts and 16,5 Amps and was connected straight to the device. So in this device you have to do nothing. You can give me more information to see if your device needs anything. Thank you!

[@Jojo-tl6io]

Can I increase the output Volts and Amps regardless of the Volts and Amps of the power source? thank you

[@techno-diathesivagelisilio940]

Hello, I have to try this but i am in holidays now. I'll try it next week snd i will inform you for the results! Thank you!

[@techno-diathesivagelisilio940]

Hello i am back so i tried the device to answe your question i wanted to be.100/100 sure so i connect my power supply and i supply the device with 12volts and 1 Ampere and from the other side i connect 2 car headlights of 12 volts in series so i increase the device to give 24 volts and i open all the way rhe potentiometer for the current to its maximum and i got 24 volts and 1 Ampere! In the video the power supply was 12 volts 16 Amperes so it had the power to give 384 watts but here has not. For anything you want to ask i remain! Regards!

[@BEATERUPTION]

Why you didn't show up wich direction you drill the current?

[@tokor5264]

hello sir, what is the default setting of current output? do i need to set it up? i just want to make stable 12v output i don't want to make current limit, my load is only 12v fan, router and for charging phone, about 60 watts only, my source is 12v 18650 battery, thank you.

[@techno-diathesivagelisilio940]

Hello! That's a good way to be autonomous in energy! The 60 watts in 12 volts means 5 Amps that's a lot of current ! The 18650 is very powerful battery but it' will be overheated giving more than 2 Amps continuously so i think you need a bms 3s for 3 sets in parallel ! 3x4,2 volts so it will be safer for the whole. The bms will make sure that the batteries will not overheated and they will be charged and discharged without problems they will be balanced in their voltage all the time! If you do this i am sure that this system will be work without problems! Thank you!

[@tokor5264]

@@techno-diathesivagelisilio940 sir i want to know is do i need to set the current or not?.

[@techno-diathesivagelisilio940]

Yes!You need to set the current that's why it has the potentiometer for current setting!

[@animaengdub3855]

Hi there i purchased a 600w 10a step up converter i hook it up to a 12v 12.5amp Led power supply but i cant seem to adjust the current only the volt i want to use it to charge my 12v 50ah solar battery.

[@techno-diathesivagelisilio940]

Hello i answere the same question to another person a month before in this video please refer there! The question was from mr Anderson Cardoso. In my opinion if the courent regulation is not working you ask the byer to refund. Thank you!

[@AndersonCardoso2804]

I'm plugging the StepUp into my car's lighter and charging my notebook... but what I've analyzed is that it can't support the necessary current... the notebook's power supply is 19.5V and 180W. I can only make the stepup provide the necessary power when I put above 17v at the input. the current tripot doesn't seem to work

[@techno-diathesivagelisilio940]

Well your car's lighter has a fuse of 10 Amps so 180 W/19,5v=9,23Amps it's ok but i am sure that for charging a notebook the maximum amperage should be at 2 Amps!You can verify it with a Ammeter. To have an idea a car's battery is charging with about 5 Amps! 10 Amps is a lot of current! For the device i have two of them the one i am using in the video works perfectly the other as you said had the same problem but i noticed that the out capacitor was loose and i resolder it and now its ok! For the voltage with the pot you can regulate to give exactly 19,5 volts! 17 volts seems to be ok (4 x 4,2=16,8 volts) but i am not sure if that voltage will charge it 100% you have to check it (maybe in the notebook there is a stabilizer which receiver 19,5 volts and regulates it). Thank you!

[@SamsMediaCenter]

Hello can I get 30v 15a dc output from 19v 4.6a? If it is not possible then what is the maximum voltage and current output for 19v 4.6a input? Please advice. I am thinking of buying this module to run audio amplifier

[@techno-diathesivagelisilio940]

At first look it cannot give 30x15=450watts as rhe maximum output is 400 watts. In video we see that it increases the voltage and that is amazing about this device with the same Amps withdrawing. The device i use in the video gives 12 volts and 16,5 Amps but theoretically because if we increase current very quickly it will be shut down due to safety design of the circuit as an amplifier who needs big power at a millisecond to express the music needs is not recommended. So i am afraid i cannot help you because only if you put a stress test to the power supply in the ( real world) you are sure that is capable to respond to your needs. Thank you! I remain!

[@rodrigojimenez3530]

I got one of these and blew the fuse as soon as I connected it to my 12V battery, no output load connected at all! Anyone knows why? Faulty board or did I do something wrong???

[@techno-diathesivagelisilio940]

Apparently the specific device was problematic you ask for replacement or refund!

[@rodrigojimenez3530]

Good to know. Thanks! Hopefully they will refund my 2 hours trying to make it work 😊

[@cdias_28]

Como fasso para liga em série para almenta a amperes?

[@techno-diathesivagelisilio940]

If you see the previous video of this named (step up the existing power supply to 90 volts) there you have i thing your answer if don't please contact me again! Thank you!

[@jollybarrun1884]

12v in 24v put?

[@techno-diathesivagelisilio940]

The minimum voltage for the device to work is 8,5 volts and we can that voltage to step up untill 67 volts as it shows the video!

[@bhiknarayan3576]

Nepal me delivery hoga

[@techno-diathesivagelisilio940]

Really i don't know! I suppose if you order something in payment they will mention shipping fees and delivery method! Thank you!

[@mehmetyuksel9465]

NOT CURRENT AMP LINEAR NOT STABİL POT WORKED

[@techno-diathesivagelisilio940]

I checked again and i found that in the end of the pot turning is a little bit hard to stabilize! Maybe a different value pot or if we put in series another pot may fix rhe problem! Thank you!

[@mehmetyuksel9465]

@@techno-diathesivagelisilio940 It is written that the current adjustment pot works when it is modified as buck boost, it is not very sensitive in its current state.

[@techno-diathesivagelisilio940]

​@@mehmetyuksel9465 The pot is working as you see in the video but it responses in the end of it's turns and is a little bit hard to regulate it! Thank you!

[@why_broken5216]

Bro using 2amp wires in 5amp power supply 😢

[@techno-diathesivagelisilio940]

You are right but for a small period of time it's ok! If we use it for a long we have fireworks! Thank you

[@Dr.DRW_91]

What you did here is not relevant. You had the pot for the current set to a certain value and thus, the voltage under load was not the voltage set by you. Hence the same current at the input and output.

[@techno-diathesivagelisilio940]

I am sure that there are many ways to make that presentation of the product here i emphasized on efficiency that surprised me was that 24 volts x 2,42 Amperes 58 Watts were achieved from 12 volts 2,42A totaling 29,04 Watts. Also i had the choice to put more load as the device withstands 400 Watts. Thank you for the suggestion that will help me to be better in future presentations!

[@MyoMyo-t8j]

Can l charging 6 s 8A lithium battery