#459

[@bobbaloch3101]

4 years ago I found your channel trying to find ways to make cheap barrel stove. We as family watch your video as soon it is posted. Thank you for great contents!

[@MrEhole]

Good point. I am also guilty of this. lol.

[@bobbailey4954]

Now that you have most of the big work for the shop done and given the pace you work at you deserve to take some time off.

[@corollaae8645]

My wife and I watch together as well. I love the music you put on!

[@raybartlett2044]

n

[@wheelie642]

People just don’t seem to realize heating a big space with a tall ceiling will result in baking the upper level. Heat rises and although you are comfortable at ground level, the upper level is baking. Heating rooms with high ceilings require a lot of circulation.

[@jlmfoy365]

The older shot with you and your old dog was beautiful and brought a tear to this old man's eye. Regards Jim UK

[@mikecampanella1990]

As someone who is close to his dog, seeing your old pup on your lap brought a tear to my eye. I'm glad you've got a new little friend doing the same things with you.

[@joeantonicci8920]

broke my heart

[@jimk8520]

I caught that immediately. 😥

[@georgschmidt5281]

What a friendship a man and his dog.

[@psyekl]

Great video! My friends and I built a similar design for our shop years ago. We didn't have the benefit of the kit, but as metal fabricators it wasn't a problem. The main differences in our design were 1) The lower firebox on ours was 1 1/2 barrels long. 2) The pipe from the fire box extended almost to the top of the upper barrel while the exhaust had a pipe reaching down to near the bottom. This forced the heat to linger in the upper barrel longer before exiting (with a damper on the outlet above). 3) we included a clean-out on the back of the upper barrel for the inevitable ash and soot that would accumulate over time. 4) We enclosed the entire unit in a sheet metal box with two openings: one high on one side and another low on the opposite. The shop was big, so we added a fan from a swamp cooler to the upper opening once the heat built up and ran it all day (we were not off-grid). We were able to keep the shop warm through the coldest winter months, and it was the favorite gathering spot!

[@albertstoltz4712]

Nice, I have a barrel stove at my cabin. It’s been there for 20+ years. I always make sure to add sand to the bottom up to the lower dampers. Few inches of sand saves the stove for years! Nice work man looks good!

[@Loyaltothefoil8]

I like the sand idea…

[@christopherstark7585]

Great idea!

[@larryjones8928]

Don’t need sand just let ashes build up and it does the same thing

[@KVX21]

​@@larryjones8928 Nahhh sand better!!

[@NeillWylie]

Never thought of doing that with sand. Awesome!

[@kylemarquardt6421]

Seeing Ruger on your lap and seeing Ruby on your lap brought a tear to my eye. It’s hard losing a dog who essentially is a family member. They were happy tears, but I sure miss my Max. Thanks for the awesome videos.

[@TheMitchyevans]

Good to see a good companion dog back in your lap in front of the fire.

[@grandmasfavorites]

Happy you now have Ruby but still, share your memories of Ruger with us. He was such a beautiful dog. Thank you.

[@r.f.736]

My dad built one for his home...one for our ranch home 30 years ago. Put in basement. Kept the whole house ok! Our clean, new, heavy duty barrels came from my husband's plant. Best wood stove we ever had!

[@SpicerStephenD]

Brings back good memories, my dad couldn't read or write but he was good at figuring things out. The first time I'd seen a double barrel shop stove was when he built one, door, inside baffles, exhaust pipe, air inlet, stand and that's what I can remember. I really miss him some days!

[@webefree]

We used them to Heat Yuge Green Houses that were 40'x120'!

[@WilbertRobichaud]

My dad was a machinist 1948 , and had his own machine shop. He builds one for his shop. The difference with yours, he also cut the top drum and attached a square tubing insert in it. The square tubing was the same size as your bottom door. The top drum then would have a square hole all the way through. He would warm up some of his steel in the top drum or keep a warm teapot and food to keep warm. Merry Christmas.

[@skypopgore]

That video four years ago is the reason why I found your channel in the first place. I’m still watching. Thank you so much for sharing your life story with us.

[@faithevrlasting]

So heartwarming Heath. You made me smile at A Boy and His Dog.....🐕🐕

[@remoc52357]

Bud the best thing to do, like I did is use refactoring mud and brick that is curved on the inside. I didn't know about this in the 1st one I built like you.......but the 2nd, I learned an incredible lesson to use the brick and mortar. I have a dble that is now 32 yrs ole!.

[@incognito8448]

you got a great voice and cadence for narrating and story telling

[@DoggoneitTrivia]

Heath & Ruger awesome. I heard a line the other day. "The more time I spend with people, the more I realize I love my dog".... People are okay, but a pup gives 100% unconditional love !

[@mat2436R]

Red poppy ranch is the best! I have watched since almost the beginning. There is not one single con about the videos to the people the music choice and the narration. Puts me in a place of peace.💚

[@colin101981]

It's great to see you and Ruby bonding - dog's truly are man's best friend! Fire looks amazing too!

[@sd90mac61]

My buddy from Houston made my father one similar to this, but it's out of steel, 25 years ago, dad's been gone for quite awhile now, but I got that heater still in the shop it's still workn fine, I like seeing glow cherry red (sometimes) not always, it's very heavy but I can always move it if I have to with our hoist on wheels. The legs on ours are 3' high and were easily able to remove the ashes, with a wheel borrow, he even made a grote that can be removed for cleaning and can be reinstalled. Excellent project partner, always helps beat the coldness, Thanks for sharing this with me. 😊🤠✌️👍.

[@DavidHotrum52114]

I was born and raised in Spokane and built a few wood stoves. When I worked for Case Tractor in Bend the shop manager gave me permission to modify the barrel stove. I added an air intake in the back of the stove using the 2" bung. It went up inside the pipe between and stopped at the edge of the 2nd barrel. There was a water culvert about 10 inches in diameter already in the 2nd barrel and a box fan mounted on the 2nd barrel to push air through and get it out. Firing up the stove after i modified it made a BIG difference. The culvert got red hot. The box fan melted because of the excess heat generated by adding air. The guys in the far end of the shop said "I can feel the heat way over here!" Approximately 100 Ft. We did not change the amount of fuel we used just added air so we could burn it all. Adding air was all I did. The biggest problem with heat engines and things that make heat is NOT ENOUGH AIR

[@junns]

I can’t believe it’s been four years I watched that then and here we are again amazing content. Keep inspiring and thank you

[@ve3yjt]

If you got a chance during the summer, you might want to flip the connector between the barrels. The way you’ve got it installed, looks like you’re going to end up with creosote drips/leaks at the joints. The upper section should always slide inside the lower section, not the other way around. Cheers!

[@paulrobinson3528]

16:10 Ruger, i miss that lad so much, i really do, what a great dog and companion he was.

[@brianleary137]

Two things to consider line the bottom barrel with 1/2 thick fire bricks makes a big difference in stove operation and longevity. Second item paint the barrels black the heat will transfer better to the outside of the barrel; the black will bring the radiant heat to the outside. Don't get too close to the rafter with the stove pipe in the event of a flue fire you need triple wall pipe or 3 feet from any combustible surface. You did a good job on the stove.

[@exposingthetruth3821]

Mine is ash bed only and was built in 1996. Used every year for 6 months a year or more.

[@portnuefflyer]

@@exposingthetruth3821 I never burned out a drum stove, just an ash bed seems to work just fine. Besides, another drum is cheaper than buying firebrick.

[@wegmandan]

You can also save even more money with angle iron and flat bar instead of that cast purchase. Also use handles as that round bar? And then go to your Auto center to even buy the springs and tackle that over the handle so you don't get burned when you grab that round stock as a handle. I'm always looking to be better of what I built. But not cheaper. But self-sufficient.

[@faiwaka]

As a "city-boy" your way of life wouldn't be for me BUT the life you have built for your family off grid is inspiring! You are easily one of my favorite channels on KZbin and I look forward to your videos every week

[@cryptoprepper2933]

You better be getting out of the city if you know what's good for you, but it sounds like you don't. Just give it another several months. By this time next year you will wish you were not in the city.

[@nenaenriquez3480]

Highly inspiring! Warms up the soul to see your inner strength together with your wife. You are building not only material things although beautiful your main action is raising real human beings for a better world. Blessings 🙏

[@paulrobinson3528]

8:25 the lighting in there is awesome, just look how light and bright it all is. Just fitted 4 double strip lights in my shed, its so bright, its brill.

[@derickwilliams2195]

Thank you for being kind to the doggy. God Bless you.

[@vnrkain1169]

I made one of those for my shop in '74 and ended up working in a T-shirt with all the windows and doors open at minus 30. All I used for fuel was leftover sawdust and wood pieces. Sweet. Very sweet.

[@ronwhite6719]

Awesome heartwarming video. Ruby was definitely born to fill in for Ruger. RIP Ruger

[@micahgahagan4282]

Great video! So happy to see Ruger and then Ruby on your lap enjoying the heat along with you 😊!!! Heath, do your heat source the way you want to...you know what’s best for your situation. I’m sure you will be “perfecting” it, as you always do with everything you work on. This video just gave us a glimpse of the great resource that you created! Keep up the amazing work!!! 😎😊🔥

[@mikedonahue4033]

Just a suggestion - line the bottom of the lower barrel with firebrick, and burn the wood on top of the firebrick. It seems to me that the burn barrel would last longer that way.

[@tedbryer2512]

Adding sand will work too. It saved the barrel for another couple of years.

[@kenwhite6449]

I built one of these a few decades ago, and I lined the bottom half way up the sides with firebrick. It worked great. Never cherried the outside of the bottom barrel

[@frederickshipp8013]

40 plus years of heating my house with barrel stoves,still do.I have NEVER burnt the bottom out of a barrel. Don't put sand or fire brick in the bottom of your barrel all it does is reduce the room you have for wood.

[@RandallSullivan-i6i]

It will,Also the firetrucks will hold heat longer

[@ricktarded5943]

There is Gold in your wisdom. Thanks for sharing. Must say, Hope you never get rid of the K10 or K20, whichever it is, and keep the three wheeler running too.

[@johnspruit7296]

i can always respect a man who is a DIY'er and loves his dogs !

[@joelongrid7625]

There is something about smoke rolling out of a chimney that just warms the heart. Great video as always.

[@tomfinn3477]

I think you and your family are a credit to yourselves! I've been watching every episode for the last 3 years and to see the beautiful home you've made for yourself up in the snowy mountains is a tribute to the hard-work and immense effort you've all put in to making your venture a success. Happy holidays! - a loyal fan

[@icehog3454]

Great stove for the shop. Can’t wait for you to get the overhead door installed. Little drywall on the ceiling and some insulation blown in the attic and your set. Stay warm Heath.

[@lakeeriehouse]

Add a cat/dog door to allow safety and warmth for the cats please❤️

[@jameskarwacki7092]

I also built a double barrel heater almost the same as your heater. Only differences are that I notched a rectangular opening into the back of the top drum. Size of opening 3/8" x inside diameter of the drum at the center. I inserted a steel plate as wide as notch in the back of drum x 6" short of the drum height an welded it to the back entry notch, and along both sides to create a heat directional barrier plate. My connection from bottom to top was located on back of drum. I also lined the inside bottom of the bottom barrel with brick covering 1/2 of the bottom radius. This heater lasted me for just short of 15 years. Also did not have access to kit so I fabricated all that was required. It was built in summer of 1977. Your heater is well built unit. James karwacki

[@mudgrippmike3489]

nice setup there.. I always close the door after starting the fire, so It will huff and puff, and pull that air in to get the wood going....keeps my tent warm while hunting in the mountains.

[@EmpoweredPercussion]

Music selection and the old and new pup was everything to me in your video. We came here to build, thrive and live. Keep doing what your doing and hope rinse a second level in the shop some day. ✊🏼 Aaron, drum builder out of MN.

[@Ratz8861]

You should have built a wire grate wood platform in the bottom barrel took keep the wood off the bottom which should help the barrel last longer. You could've even put tubes completely through the top barrel making a heat exchanger type setup, and then put a fan on the back side to blow air through on those really cold days.

[@GreatestWhiteHunter]

In the beginning of the video I did see some burned out grates on the floor. But you are correct. I how ever have two 55 gallon stainless steel barrels that I will be doing the same. S.S will out live me.

[@davidchappelle6480]

I KNOW this was 2 years ago !! You could have put a roll of copper pipe in that top barrel an had endless hot water too ! Provided you had a good water source ..

[@NeyJ]

That ending got me feeling emotional!

[@milesboulton9885]

Rarely have I heard music that is so peaceful on a video of this nature... so uplifting compared to the mindless rock that seemingly permeates everything from retail stores to sports in our culture. Thank you for a great video. God bless, Miles (BTW, my family and I live in WA State just 7 miles from the ID border. Considering our politics, I've often wished I lived about 8 miles east of here.)

[@jeffburnham6611]

We took our local Boy Scout Troop on a weekend camping trip in mid January several decades ago. The trip was more of a chance to practice on some of the skills needed for the upcoming winter jamboree, plus a reward for the boys for a high number of advancements in ranks and merit badges earned at summer camp (the reward was a "pizza pig out", with 3 cases of pizza's, 25 pizza's to a case!). I remember the shelter we stayed in had a large area to put down sleeping bags and cots, and an area with a stove and kitchen, In the center of the shelter was a double-barrel stove. That thing put out so much heat you couldn't be near it, but it heated up the area very well.

[@je-fq7ve]

consider adding an external air source to feed the stove. Like a 6" stove pipe thru the wall of the shop with a damper. Right now, you are using the warm air in the shop to feed the stove. That air has to be replaced with fresh air creating drafts. By taking fresh air from the outside you avoide these pitfalls. You will use less wood and feel warmer.

[@metalpolishshop]

I have experienced the opposite. When it is -20 and below the sir is just too cold to make a proper burn. Went back to using a small 5/8" hose to add replacement air to the building

[@je-fq7ve]

@@metalpolishshop As long as you are making up the air somehow is what matters. In your extreme climate you will have more things to consider.

[@joesinakandid528]

@@metalpolishshop Winter of 1966, Mendeltna Alaska, air temp minus 81 (REAL air temp - not fake "wind Chill"). Without question you're wrong Kevin, dead wrong, our barrel stoves ALL burned just fine. - Joe -

[@dogwoodtales]

There are some reports that say using outside air is not beneficial. Assuming that those are incorrect and it is beneficial, how does the wood stove use less wood simply because the air supply is from outside?

[@je-fq7ve]

@@dogwoodtales Look outside at you chimney when a fire is going. That column of smoke was recently warm air inside your shop. The warm air has been replaced by cold air being sucked into replace what went up the chimney. Supplying cold air to the stove from outside breaks this loop.

[@Thrashedcrow]

I was literally just thinking of RPR, and whether there was a new video. 2 minutes later bang why yes, yes there is. 😂

[@eijaroth5740]

Greetings from Finland, I've enjoyed watching your journey since the beginning and am still in awe how wonderful it is...thank you for every week that I have a reason to get up and watch you and your family be so positive amongst this cluster f and hope we all can get back to normal asap, hugs to Ruby and everyone else, stay safe and healthy, may your Christmas be merry and bright!

[@MG-ok6nu]

Finally a video where the music isn't annoying. Wonderful addition to your great video.

[@subliutenant]

I worked at a farm engineers yard at Faversham in Kent in 1981 and the owner had made one of these to run on old engine oil drained from farm machinery having services. There was a round metal dish in the bottom drum, near to the front opening, there was a four inch pipe joining the two barrels together at the other end and an outlet or chimney at the front end of the top barrel. no vent holes other than the front door and the chimney outlet. a copper pipe was brazed in through the side of the bottom barrel and into the metal dish. a piece of rag was put into the metal dish and soaked with engine oil and then lit. An isolating valve on the oil line feeding the dish, was used to regulate the flame. When the flame had been regulated, the barrels could be run at 'dull red', ideal for toasting bread on a toasting fork. An amazing amount of heat was produced and the flame adjusted so very little or no smoke was visible from the chimney. So heating a large workshop, cost him nothing! A brilliant idea! But not so environmentally friendly these days!

[@bigolmoose8857]

Suggestion: Try putting about 2 " of sand in the bottom burn barrel, prolongs life of that barrel. All the Best

[@hpw59]

I thought they came with a grate to keep the wood off the bottom of the barrel.

[@FallLineJP]

Probably helps increase the thermal mass too. Good tip!

[@gunlindblad799]

Or use that ceramic mass to cover all the walls inside?!

[@Showahnee320]

They have ceramic bricks for the bottom as well. My husband tried the double barrel some years ago. He couldn't get it to draw correctly. Hope you have better luck.

[@minorcross980]

Sand is a good idea, or a layer of fire brick?

[@AMG63]

I remember that first one you built many years ago, that's how long I've been watching for 😯 and I've enjoyed everyone you have uploaded ( apart from the obvious one).

[@the4thj]

Very nice! As a former Minnesotain, we used to do some trick welding in a center small barrel half the size in the second barrel and add a fan blowing through. Also, we used fireplace door cord everywhere to air tight it.

[@Dtsmith69]

I have been following along since back before you poured the foundation. I dont think I have ever commented before. But just wanted to drop a note, what a story of challenge, struggle, success and adapting. And it all revolves around family. Merry Christmas y'all.

[@georgehardwick9460]

Where did you get the radius collars and hardware from? Is it a kit?

[@davidcudlip6587]

We had a similar double barrel wood stove in our shop at work. Worked great. We lined the bottom barrel with fire brick. Stood an electric fan on the side of it to force the heat further from it and used it for many years. Cost all of about $20 in materials.

[@11jdstein]

Heath, while religiously watching your videos, it just occurred to me that one of the best aspects besides the alignment with many of my own values was that the pace of your videos is just the perfect balance between time lapse and live to keep people simultaneously informed and entertained. Great work!

[@dougburke50273wind]

Great video, find a small fan and have it blow across the stove, it will make a tremendous difference for heat output into the shop.

[@dericksmith2137]

- I agree! I had an old 16” mounted in corner at the ceiling blowing down right at the exchanger barrel. It made the difference between a warm concrete floor and a cold one. Also speeds up the overall feeling of warmth throughout the area. I also did a cinder block fence filled with field stones around the stove.

[@moes8137]

If you go to Tractor Supply and line the bottom with fire brick all the way back in about a quarter of the way up the sides it will last a hell of a lot longer and I even found a great that I used for like a storm water on a street and put a grate in the bottom and burn on the grate instead of on the metal it works well in my shop

[@larrybailey43]

I liked the idea of adding 2-3” of sand int the bottom of the barrels to help prolong barrel life

[@betpatpatten3840]

Will you line the fire box with fire brick? Seems like that might help the fire box keep in better shape from hot fires.. looks great!

[@avflyguy]

Protects the bottom of the barrel too. Over time, it'll sag and get leaks in it.

[@farmerbill6855]

The best thing is to keep about a 4" layer of ashes in it.

[@BloodyKnives66]

Built one 3 years ago add sand to cover the bottom and it'll last awhile, mine is still working great. Recently bought a house with a double barrel stove already in the garage.

[@KingsOutdoorLife]

My neighbor has one of these in his shop. Works great. Keep it up guys!

[@kirbyroad5743]

I didn't notice in the video whether you added sand to the bottom barrel. I've ran these in my shop for the last 25+ years. I always put the door up as high as possible on the bottom barrel and that leaves me 3"-4" of room to add sand to the bottom of the barrel. I get 10 years out of the barrels before I have to rebuild. Mine is ran daily 7 months out of the year so it gets alot of wood ran through it. I'm on my 3rd set of drums now and I'm getting new ones for it next year. These stoves really work great.

[@garynicholls72]

Gary here from the UK, as one plumber to another sweet project have you thought about adding angled Finns to the unit, I think it will add more surface area to the unit thus giving you more heat for wood brunt just like radiators plus baffles inside the barrels to slow the heat down and give more heat into the barrels and you might think about adding a coating or sand on the burn barrel only half way up on the inside to make the barrel last longer .I hope you think these ideas are useful. Very nice video very interesting and informative keep them coming thank you

[@hughmanatee7433]

You can extend the life of the barrel by putting a little sand in the bottom to make a flat spot, then a layer of fire brick on top of that. You can even lay up some bricks on the sides.

[@jamesmartin3914]

100% agree, when you star to see pin holes forming.

[@raspano1]

My hunting gang used a drum stove for the hunting shelter. It was homemade and rough. Also we rigged a flat top and that was used to heat water. For cooking and washing. After ten years it is still in good shape. Love the barrel stoves

[@geneanuts]

My husband built a double barrel stove in '78 in TN. It was still going strong when we moved in '85.

[@davea5113]

Looks like a beautiful homestead, a little piece of heaven!

[@trailguy]

I clean all the 20 chimneys on my farm each year and am always thankful for the ones that are straight. Do you need that zig zag near your roof? It’s so much easier to push a brush straight through instead of taking the pipe apart each year.

[@Thrashedcrow]

Good to see you found your new buddy, Ruby!

[@bigcharliesmodelgarage296]

Those are nice. Use one in a 40' x 64' shop. Used barrels with removable lids and built taller stand to set barrels on. Also put firebrick in bottom barrel. I've had it for 15 years now.

[@srheffington]

Merry Christmas Poppy Ranch! If you add fire bricks to the bottom one it will last so much longer. I love watching your channel!

[@MikeySkywalker]

That dog adores you. Beautiful.

[@eddiereyna2998]

I enjoyed every bit of your shared experience and reading about the comments about your dags as well . I really liked the song , very suiting for a family man . Thanks fer sharing this .

[@da_ghoul9432]

Look like Ruger sent someone someone to watch over you, he knows you need it. Rest in Peace Good Boy!

[@ktrn2b]

God Bless Ruger, sweet boy.

[@guerillacity]

Always relaxes me on Sunday watching these :D

[@-TheSingularity-]

Put pipes through the top barrel and a fan behind it, almost like an inside out radiator ? Or use the top barrel as a heat exchanger and use it to heat water for radiators ?

[@manolisgledsodakis873]

Interesting idea!

[@davidstevens1522]

I worked in a 4000 sq. Ft. Machine shop years ago and the cost to heat it was crazy. We built a double decker wood stove out of old boiler tubes 3ft x 8ft. And put the tubes in the top barrel like The Singularity recommened along with a fan. Some 20 deg. days we would have the doors open because it would get so warm in the shop. Love your videos and hope you and your family have a merry Christmas

[@crickittorres8077]

So beautiful. Your place is just awesome. My daughter bought a place near Klamath Falls Oregon.soooo it's going to be tough but I watched my mom and dad and family now I can pass that on. As a woman I can help her understand from the get go the challenges and how they are all worth it.

[@chuckcribbs3398]

My wife and I filed our mortgage application last night on 8 wooded acres in Central Ohio. Fortunately we have a 30’x40’ barn on the property in good shape. Just need to put in a concrete floor. Then get it ready as a weekend living space until we sell our house. Excited but nervous. Another month of waiting on soil test, appraisal and approval from the bank. Fingers crossed.

[@damienspann315]

I have a similar stove set up. And I’m willing to bet that toolbox gets relocated. It won’t blister the paint but it will blister you every time you need a tool. Nice work

[@garybrewer6218]

Love this idea! So much cheaper and you can fix it later when they wear through.

[@Vladshock]

My parents had a double barrel stove as our main source of heat when growing up in Alaska. It seemed able to more effectively warm a cold winter house than any fireplace we have had since. It had 40+ feet of chimney and I don't remember it having any problems with draw, did have a couple stack fires though.

[@davidgreve1081]

Nice stove! They can put out a lot of heat too! The thicker the wall on the barrels, the longer they will last without burning through . Great job and your shop is warm throughout the winter regardless of how cold it can get outside. These are Very efficient stoves! Those Idaho winters can get brutally cold too! I lived next door in Montana and it was nothing to get down below zero farenheit during some of those snow storms. Some winters would get down to 60 below zero. A stove like this one is like gold in those kind of winters.

[@frankpatterson9453]

learned a few things when i put my barrel stove together. #1use a barrel that has a removable lid. #2 lined with fire bricks #3 put door high as possible so you can really pack it full. #4 slant door so it naturally stays open when filling. I welded a flat steel plate so i can cook

[@redhorsepill5060]

Great build! Consider safety glasses, especially when using a cut off wheel. You have a family to take care of, God forbid you lose your sight.

[@garyofnyc]

He's a good man--and thorough! M. Lebowski

[@shedroids]

Simply awesome! Blessed are the hands that build.. and nothing brings greater reward than building your own!

[@ssranch6017]

We had one in our shop that dripped used motor oil. It would run you out of the shop and it was a big shop. Thank you for the video sir. God bless stay safe. Hello from Stuttgart Arkansas

[@pigskinfanboy]

This is a very similar setup to a double barrel stove that one of my bosses made in a shop I worked at in the mid 90’s. He dripped used oil down inside the bottom barrel. Was basically a copper tube with a ball valve. Pipe went into a hole drilled in the top. That thing would run you outta there even on the coldest days. Had a large fan blowing behind the top tank spreading the heat across the shop. Very nicely done.

[@johnelliott4521]

Lining the barrels with fire brick helps longevity, also putting tubes in top barrel and fan realy helps heat output.

[@stevenf6161]

I made one of these 40 yrs ago. I slit the upper barrel and inserted a plate to make the flue gas make a 2nd pass in the upper barrel, welded the seam to make it gas tight. Worked great.

[@MetaMorphea]

Really surprised when you mentioned retaining more heat for the double barrel wood burner why you didn't add rocks to the second barrel. It would have been fairly easy to have a small metal grid so they don't fall down and use large rocks that would let the air flow through but still massively increase the heat retained hours after the fire has gone out. Just a thought.

[@blainwilson7937]

Creosote build up is why that wouldn’t be a viable option.

[@robertdraw7726]

We used a double-barrel wood burner in our shop when I was young. Very efficient.

[@bendiede7982]

We’ve used a double barrel stove in our shop for 30+ years and depending on what you burn (rail road ties, rubber, oil, burn a lot dirtier) you shouldn’t have any issues getting that stove to draft. You from time to time have to climb up on the roof and drop a length of chain down and rattle it around to clean out the stove pipe should be about it. Good luck! If you wanted to get fancy I’ve seen guys weld some exhaust pipe horizontally through the inside of top barrel and run a fan on it to really maximize your heat output. Some other “homestead” type KZbinr did something similar.

[@INKJAX]

next time try a propane tank for the fire tank.. much thicker, holds heat very well and, will last for a long time... i use them to built bbq's... some are well into 10 years old with no issue and they are used year 'round...

[@paulhoneyman6923]

love these notifications, means it's time to get the kettle on and enjoy it. God bless you

[@cubbysrig]

There’s nothing like the relationship between a man and his dog. We always remember the good ones.

[@daisysmum7336]

My dad built something similar almost 50 years ago to heat our house. It was made from a half oil tank with a welded metal lid, ice cream freezer door and oven racks inside to elevate the wood. He would later fine tune things by using an outside metal casing from a clothes washer to surround the stove and fill the space between with rocks to help retain the heat.

[@44thala49]

I built using the same kit but used a stainless barrel. I love mine. I heard a tip that said that if you use a regular steel barrel to put sand in the bottom of it and it won’t burn out the metal as soon.

[@MrTonyPiscatelle]

I built one of these from a kit about 40 years ago for my small body shop in KY. I lined my burn barrel bottom with sand and firebrick. I also welded in about 10 one inch tubes from end to end on the upper barrel and mounted a fan on the back to get more heat out of it. She would run you out of the building and was good in the winter when painting instead of the ceiling mounted gas forced air heater which blew dust everywhere.

[@garysamons9332]

holy crap...this is the first time ive ever heard someone doing the sand thing....i have the same setup in my shop including the sand and i used regular flat cinder flat blocks...in the summer i wire brush the bad spots off and spray with high heat stove paint to keep the summer rust down...no signs of rust through...and its been cranking out heat for the past 5 years...i also use a small cheap fireplace grate that i had laying around to give the wood some air underneath.... just put a window fan behind the stove elevated up about 7feet and angle it down toward the stove and let it blow...btw my shop is also in KY also.....Hillbilly ingenuity 💪