4th gen Camaro window motor replacement

replacing a driver side window motor on a 2002 Camaro. OH WHAT FUN IT IS TO RIDE IN a dead window Camaro.
Would you like a glass with my logo or your own personal logo? Contact BNC LazerWerks www.etsy.com/listing/76024924...
Disclaimer:
Due to factors beyond the control of Chemical Spore, I cannot guarantee against improper use or unauthorized modifications of this information. Chemical Spore assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Chemical Spore recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Chemical Spore, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Chemical Spore.

[@joedq]

Great multi repair video. I picked up a 95 V 6 T Top yesterday, both power windows don't work, so glad to see an all in one video from taking the door panels off to replacing motor. Thanks for sharing.

[@chemicalspore]

You are welcome and congratulations on your purchase.

[@TheDaninator]

The plastic on those door lock/window switch bezels are cheaper than dollar store squirt guns! Nice work on the window motor CS! 😎👍

[@chemicalspore]

hahaha, Ive cracked a few of those in my day so I know the carefull ways around it. That cheap plastic dash pad is the one that im worried about.

[@TheDaninator]

Chemical Spore yes, the dash pads are crap plastic for sure!

[@CamaroRick]

Ive done it by removing the rivets for the whole regulator. The regulator rivets are steel and dont drill out well but this way seems like a good option without the need for any glass adjustments!

[@chemicalspore]

It sucked that the 12 tooth motor didnt work, that one was an ac delco that I have to send back. I had to get a piece of crap dorman that i might have to replace in a year lol

[@CamaroTime]

Great video. There is another way but even more of a pain. It involves removing the whole glass, track and all.......So the holes are the best option. And done right they look like factory. I am fixing to pull my stereo out and check everything. I have started getting a pop in my factory Bose sub (which normally means the factory amp is going out) and once in a while I get feedback/static in my front speakers. So I am pulling everything and checking all connections, wiring and all. YAY what fun.....

[@chemicalspore]

It is funny that you mention the stereo I am actually replacing all my speakers right now which there will be a video on that probably tomorrow and you better make a video on what you're doing

[@Xelaon]

Really good high quality vid appreciate it!

[@chemicalspore]

Glad you watched it. Thank you

[@kobesitdown5921]

what is the color diagram for the electric windows, i have a 94 and i can get my window to roll down but not up and i can’t figure out what wires go together to make it go up

[@chemicalspore]

www.autotrix.net/install-instructions/93-02-firebird-camaro-driver-express-down/

[@themaintenanceman1]

That’s not a race car 🙄. Lol well done getting that motor in. It will be super easy the next time if there is a next time. Great video buddy!!

[@chemicalspore]

Hahaha. Street car? Yeah lol. Thanks buddy.

[@hectorleon8373]

What did u use to secure motor with since you removed rivets?

[@chemicalspore]

Bolts and nuts that came with the motor

[@xephael3485]

0:56 Looks like you've got some junk in your door pocket to get out too😁

[@chemicalspore]

Its not junk its treasure.

[@xephael3485]

6:17 couldn't you have cut old harness off that speaker and spliced into new speaker? That would let you use factory hookups without buying new harness. 11:30 I'd have just reused old one.

[@chemicalspore]

Wait for the next video Sonny boy

[@mizravenkustoms]

Oh dang I was hoping you showed putting the door panel back on I’m struggling long story but I had it off for too long

[@chemicalspore]

Make sure the upper lip slides in with the tabs also being able to go into their slots. Its kind of a pain.

[@mizravenkustoms]

@@chemicalspore thanks for the tip. I think part of the issue the panel got warped a bit 😭. Totally my fault for lagging on putting it back on. I got that nasty black glue all over the place too 🤦🏻‍♀️🤦🏻‍♀️🤦🏻‍♀️🤦🏻‍♀️. Im the worst procrastinator 🤦🏻‍♀️.

[@chemicalspore]

@@mizravenkustoms lol. Poor thing

[@yaboyscottay]

No idea if you’ll see this anytime soon…. But thank you for this video, seriously helped me out. Only thing is, how did you remount the motor? Drilling out the rivets leaves a lack of mount… so I figure bolts and nuts will work just to hold it in place but let me know what you used please! Thanks again for a very helpful video

[@chemicalspore]

Yes, I drilled out the rivets and used nut and bolts to put it back in place. Will make it easier the next time these damn motors go out. I am glad this helped. I enjoy making this videos. Than you for taking the time to watch

[@yaboyscottay]

@@chemicalspore Of course! Thanks for making the video for us. Also, it was only after I commented that I found out my window motor came with nuts and bolts of its own... I had already search my random ones in my toolboxes and installed it when I looked into the box and found the new and packaged ones that came with the motor... hahaha. Oh well, my motor works great now so it doesn't matter.

[@chemicalspore]

Heck yeah man. Next time you have to do it, it will be easier. No more drilling.

[@lightsoutmedia7370]

My biggest fear this year because the end of last year I rolled my window down and it was stuck it took about a doesn’t presses to of the button to get it to go up I wish it was just the switch

[@chemicalspore]

You live in Michigan or something, right?

[@lightsoutmedia7370]

@@chemicalspore yes sir the weather is finally about to break and I’ll be pulling her out soon

[@chemicalspore]

time to fix that motor for your window

[@lightsoutmedia7370]

@@chemicalspore you know it,last year I was looking at the wrong vids I thought the whole assembly had to come out had I known I would’ve handle this last year

[@chemicalspore]

You can actually change out the whole assembly, it comes with a different style motor. I would attempt it if I had assurance that it would last longer.

[@robchap8962]

I think you forgot to Tell us about the specs of the radio.....or how many lumens the dash lights put out....

[@chemicalspore]

or how much sun radiation the T-top tint blocks out

[@robchap8962]

@@chemicalspore lol

[@Arden2886]

Think you can replace my passenger motor? Hahah I don’t want to attempt

[@chemicalspore]

where you live

[@Arden2886]

@@chemicalspore pinellas county. Not far from you 😆 I’ve replaced a lot on my fbody from your videos. Bump stops. Speakers. And some more

[@chemicalspore]

@@Arden2886 [e-mail] email me

[@Arden2886]

@@chemicalspore I didn