6.5 Creedmoor- 95 gr. V-max and Varget

[@longgone13]

I run these 95's in a 22" Tikka, Nosler brass, CCI200's, 2.650" COAL; 47.0g of H4350 gives me 3090fps. No pressure signs in my rifle, and while mostly used for varmints out to 400 yards, they have held MOA on steel out to 750y. They make a red mist of prairie dogs and they shoot nice and flat!

[@IU_RK84]

Did you notice the bullet is not seated very deep? Other manuals with similar grain bullets are 2.60-2.65”. Found it odd. Would like to measure a factory Hornady varmint express load.

[@rex8958]

Lower BC for the .264 caliber but for varmint bullets it’s a pretty good BC

[@mitchkubacki5286]

What is your COAL on these rounds?? I have found 2.710" to work in my bolt gun but had to shorten it up for my ar10 have played with 2.68 and 2.65 both seem to function, and the bullet stays in the case with a light crimp but have not tested extensivley enough yet to give final accuracy results. Also using varget powder and at 41.7 grains

[@308alaska]

I've been using STAR Brass and have very loose primers after just one reload! I'm using publishes data so I'm think the brass is not so good. Just a observation.........Thanks for posting. It takes alot of time to do one of these videos!!

[@224valk4]

Ive had at least 6 firings with starline brass & have had super tight pocket up to t uses. But im using small rifle primer brass with cci 450

[@slamminhawgs9847]

im going to be trying my luck with 95 gr out of a Ruger AP. tried the factory loads and it didnt like them, have 200 projectiles to load up. thanks for the info

[@hoffmiermp]

How do those bullets perform on hogs?

[@slamminhawgs9847]

@@hoffmiermp not sure, only used 140 gr bthp, 140 eldm, and 143 eldx

[@savagereloader6699]

Definately gonna have to give these a go. I didn't think they group so well in the 1:8 barrel. Thanks for posting dgunnut

[@dgunnut6550]

You’re welcome! Thanks for watching!

[@virusworld3730]

Can this drop a hog?

[@seanfronczek7344]

I shoot 95 v max on my creedmoor pushed by 43.4gr varget, win cases, and cci 200 large primers. Coal of 2.590 if it groups bigger that .35" @ 100 yrds than it's me.

[@michaelhayes7431]

what barrel twist?

[@fjb4932]

@@michaelhayes7431 1:8 ROT

[@stapletonb08]

What barrel twist you have?

[@dandingfelder6763]

What is your barrel length?

[@dgunnut6550]

Barrel length is 26”.

[@12vibaba]

broke in the barrel... ok you lost me. its not a 2 stroke engine.

[@MrFritzzz666]

Steady the damn camera You aren't making a culture piece.

[@joeytheratbastard1873]

Using 41.5 varget in hornady or nosler brass with a Winchester lr primer @2.68 oal. Have not had a chance to chrono these loads but can tell u they were devastating on rock chucks out to 425 yds

[@michaelhayes7431]

what barrel twist?

[@hoffmiermp]

Lol, that was my sole reason behind getting those bullets, woodchuck hand grenades upon impact. 😁

[@joeytheratbastard1873]

@@michaelhayes7431 1/8

[@joeytheratbastard1873]

@@hoffmiermp got a pdog this june at 415 yds wish i could load the video

[@dandrevanzyl6291]

Whats your barrel length?

[@fjb4932]

26" Still ...