{636} Convert ATX PSU Into Variable Power Supply, Increase ATX Output Voltage

[@vicentematricardi3596]

Excelente como siempre tu forma de enseñar , se trata de un gran maestro de la electrónica lo que haces , Muchas Gracias por este y todos tus trabajos anteriores !!!! 👍👍👍👍👍👍👍👍

[@HaseebElectronics]

Hello I am grateful for the beautiful and encouraging message. it is a pleasure that my efforts are useful for my viewers. please accept a special thanks for your comment. stay blessed

[@vicentematricardi3596]

@@HaseebElectronics Mis Bendiciones para ti , eres un ser merecedor de agradecimientos porque lo que haces es digno de una persona de un gran valor Humano !!!!

[@benesbertv5248]

@@HaseebElectronics have a great day sir. i am your follower here in the philippines. i have a question regarding this computer power supply because we can buy a cheap price of this a secondhand. i plan to make this ATX to supply my booster amplier with an input voltage of 45v dc, can i increase the voltage for up to 45v dc? how about the current because my atx supply indicates 25ampere 12v+ it means if i increase the voltage to 45v the ampere is the same 25ampere or it will decrease to 5ampere something. but how can i get 45v dc of this power supply. i hope you can read my message. thanks.

[@AurelioMoreira-y2s]

Muito bom

[@amarandos2]

Κύριε Haseeb τα θερμά μου συγχαρητήρια, είστε ένας υπέροχος δάσκαλος στα ηλεκτρονικά, και μοιράζετε απλόχερα τις γνώσεις σας. Σας ευχαριστώ πολύ από Ελλάδα.

[@LeobieLang]

no clickbait title like xV to xxV all usable information thanks man.

[@HaseebElectronics]

best regards i try my best to share my experience and limited knowledge which i have. i hate misleading clickbait tricks

[@hilariohernandezandaverde3077]

excelente profesor muchas gracias por su amable disposición de enseñar y compartir sus conocimientos, Dios lo bendiga junto con su familia

[@joelpadillaong]

Thank you so much sir HASEEB. Truly a non-low knowledge of your ingenuity. More power and God bless your household.

[@HaseebElectronics]

You are most welcome

[@learnwithjohnny4641]

Sir mene aapke sare vidio dekhe hai you tube me aapka chanal best hai sikhane ke liye bagvan apki sehat hamesa achi rakhe ye prathana karta hu👍👍👍👍

[@applepie777ful]

Thank you for your video sir, I have only little knowledge in electronics.... But I'm very interested to try your tutorial... I'm planning to use my cpu power supply to supply my car amplifier which is 12 volts 3600 watts... I will use your video as my guide... Thank you very much sir, I hope many people will learn and to have a very good knowledge because of your blog... Many thanks sir... Keepsafe... GODBLESS

[@HaseebElectronics]

You are most welcome if you are using computer power supply, most of time, maximum output can be taken from computer power supply that is 400-700 watts. while 12 volt section can provide maximum 200 watts in an excellent power supply. that will not enough to run your amplifier. moreover, you need to remove protections and then it is doable wishing you best of luck and success

[@W1RMD]

Thank you for this VERY valuable information. Adjustable current limiting is also an important feature, especially when working with sensitive circuits. So many applications for this circuit!

[@HaseebElectronics]

it is my pleasure sure we will integrate current limiting feature

[@HarlavanisPanagiotis]

Wonderful video dear friend, have a happy Sunday!

[@HaseebElectronics]

thanks a lot dear friend

[@jiouse5881]

Excellent job. Learnt lot of things from your lectures. This the reason why I subscribed your channel and following you on KZbin.

[@HaseebElectronics]

best regards and special thanks

[@hellalchtourou9993]

Bravo excellent travail et surtout très bonne pédagogie que j’espère profitera aux jeunes amateurs d'électronique.

[@HaseebElectronics]

cordialement et merci pour votre beau commentaire reste béni

[@ssmm3630]

always pray for you because you share your experience honestly

[@HaseebElectronics]

bets regards and special thanks

[@mansirrabiu7412]

Haseeb the great engineer 👍 I remain loyal to this channel 💚♥️💜❤️💕

[@HaseebElectronics]

thanks a lot dear brother it is my pleasure that you love my efforts

[@dibyendudas9686]

you are one of the best electronic content creator of KZbin but still underrated.love your video . knowledge has no barrier so, love from India.🇮🇳

[@HaseebElectronics]

best regards no brother, my channel is not underrated, i am satisfied because i am not working for views, earning, or subscribers that's why i never force for like share etc. i just share my experience, and reply the answers for my viewers so it may help someone

[@dibyendudas9686]

@@HaseebElectronics you are so humble . May God bless you sir. sir how can I disable over current protection in CG 8010 IC ? I made my atx variable but when current is about 3 amp at any voltage(e.g. 14v, 12v or 22v the smps stops . the smps is frontech 450 watt. i removed over and voltage protection by adding a voltage divider circuit by connecting to 5v SB . but still this problem happens. help

[@HaseebElectronics]

@@dibyendudas9686 best regards I will explain the current controlling technique in the same TL494 based atx power supply and will see the possibility for 8010 as well

[@techy1661]

@@HaseebElectronics I can understand how much time and efforts are needed to create a technical video, which are serving their purposes very well. I heartily respect your patience, efforts, and time, what you spend in creating these valuable informative videos.

[@abdulwahid8579]

Good job with all the best information and knowledge able video Sir you are great

[@HaseebElectronics]

it is my pleasure

[@MarkPrince1317]

That's so helpful thank you brother for always the best and easy understanding tutorials Best regards from Philippines 🇵🇭

[@HaseebElectronics]

thanks a lot bhai

[@skysurfhf]

Thanks for sharing your knowledge... Greetings from Portugal 🇵🇹 🌟

[@HaseebElectronics]

thanks a lot dear friend best regards

[@shefqetkaralliu6816]

Ottimo maestro, carissima spiegazione. Grazie mille 🙏👍

[@HaseebElectronics]

grazie mille caro fratello

[@KazsprG]

Fantastic video. This will come in handy on a few projects I am working on. Very informative. Love your videos.

[@HaseebElectronics]

it is my pleasure best regards

[@gerandpontrac2760]

thanks Mr hasseeb,very good explanation.

[@HaseebElectronics]

You are most welcome

[@rahulpatelgujratahmedabad3497]

GOOD TICHING KARTE HO AP THANKS 👍👌👍👌👍

[@HaseebElectronics]

thanks a lot dear

[@hichamtassi1753]

Very nice video !! finally what i wanted to see : a no drop voltage under load from an ATX. I have M Haseeb 2 questions before i start this project : 1- What happens if by mistake i short the output ? are there any other protections ? or should i put a fuse ? 2- Is the same principle applies to other designs (mostly the ones using UC3842/3843) ? Thank you & Salam Aleikum.

[@vlogswithraj6491]

nice sharing and good information 👍🤠

[@HaseebElectronics]

best regards

[@حسينالحداد-ث3ت]

جزاك الله خيرا وزادك الله علما

[@MusaKazim]

You have given very good information, thank you very much Along with this you said that soon you will tell how to control the current of this power supply, so please make a video in this regard as well because I am waiting for your video very much. The company's variable power supply is very expensive, so if you tell us how to control the current, it will be easy for everyone and save a lot of money. Jazak Allah

[@kanartech]

So educative, the previous voltage has amp (5v 2A) how many amp do you have in your custom volt?

[@GREAT-ATA]

Thank you sir for being such a good source of inspiration to us. We so much value your depth of knowledge and experience in this field. I did modified my ATX unit and the output varied properly I'm yet to add a suitable load though. But I also want to point to a problem I encountered and what I did as a solution. Problem:>>>> After using this trick I noticed that power resistors at the output became very hot. Solution:>>>> I removed them know they were working as a dummy load and for current measurement purposely. I'll replace it later though with a suitable one. But i'm posting this because I know some people will encounter such. And I also want to ask if you as well encountered this same problem? ....... Hope to get your response or anyone's response.

[@PragmaticVW]

thanks man, was just to make a miracle by just altering values of feed back resisters to the tl431. now i see i need to do something to the pwm ic's configuration.

[@abdulwahid8579]

Good job with all the best information and knowledge 😃

[@vijayakumarkumar9190]

Very good and useful information sir thanks for sharing this knowledge to us

[@HaseebElectronics]

Most welcome

[@stevemiller6766]

I’ve been looking for something like this for sometime, thank you. I have some HP server power supplies nice compact units with 65 amp on the 12 volt bus. Would like to do this to them. Can you suggest a source for a schematic for them?

[@jalalihammad3494]

Great personality Sir Haseeb sab🌹🌹🌹🌹🌹🌹🌹🌹💋💋💋💋💋

[@muhammadishtiaq24]

Excellent explain thanks for sharing this informative video

[@HaseebElectronics]

thanks a lot

[@muhsen61]

The short circuit for the 12 volts output still protecred?

[@nasirmehmood3585]

Thanks جزاک اللہ خیر

[@HaseebElectronics]

thanks a lot dear brother

[@penoye-techvlog6961]

Nag iimprove ako sa mga vid nyo. Salamat

[@HaseebElectronics]

karangalan ko maraming salamat sa iyong komento at mga pagbati

[@ivanilarionov1893]

Hi, thank you very much for the helpful information. I need a regulation between 2V and 11-12V. I suppose that 12 volts output cannot go so low, but is it possible to use the 5 volts output for such a range? If not, what is the max range that it can provide? Thanks!

[@olgunguldur2570]

After removing one leg of the resistors on the +3.3v and +5v output lines from the PCB board, what were the voltage values of these two lines? You didn't show this in your video.

[@MrChrisRP]

0 for each. Taking those resistors out of circuit effectively opened the circuit for them.

[@mack6024]

Mil Gracias y Bendiciones para usted

[@HaseebElectronics]

Saludos y agradecimiento especial querido hermano

[@FUNIXID]

What should we do if we want to have a 12V power supply voltage from zero to 30 volts?

[@HaseebElectronics]

by controlling the duty cycle of any smps controller it is impossible you can use a linear voltage regulator and current regulator in the output

[@ravindrajayathilake5544]

Thanks i also modified legend 250w atx pcu.under your opinion.but yellow line,Min v is 8v, max v. Is. Ok.and other o/p olso there.but velu is chang.can u help me.

[@adrianbestboy98]

I've replaced the 16V 1000uF capacitor from output with 25V 1000uF capacitor but it's going up to 18V, should i buy a 35V or it has something to do with the fact that i've soldered a 2K resistor for ground(i haven't had a 1K when i wanted to test it)

[@reubenbalie9576]

Hi, i have an ATX PSU with only 1 IC 'SG6105D' BAZ33780351E . Can i do a a similar modification to use it as a battery charger.

[@TheJavaSync]

Sir, jumper & 2 Resistor voltages sense - they are in series? 'Coz, in my case I can't find R from 3v3 only from 5v line

[@tksalalah]

What about the transformer which was designed for the 12 volt dc output plz explaine

[@SWARAJSINGH2008]

Good. How can we modify the protection circuits (the resistance network) also for higher voltage.

[@Brison1949]

Thank you Haseeb, your videos are so informative, just a question is there a way to increase the amperage for laptop fault finding ?

[@HaseebElectronics]

best regards we cannot increase amperes, because the transformer is limited at a rated current, if we will try to draw more current by hacking the protection, it will cause to overheat the transformer, MOSFETs and it will lead to destroy it rapidly

[@daryo_pl]

​@@HaseebElectronics Hi Haseeb, but how about rewinding second side of transformer to replace ​unused 5V and 3.3V windings with extra copper for increase output current?

[@Mr140849]

This modification is good, but in case of variable supply from 10v to 22v, how we provide 12v stable supply for cooling fan?

[@gabrielquarshie94]

Thank you you so much for reviling this to us this secret. My question is : Will the power supply maintain it"s normal current after the modification ???

[@Edmorbus]

Very good Thanks for sharing

[@HaseebElectronics]

best regards

[@mannmachine2937]

Very much useful. Thanks you very much.

[@HaseebElectronics]

You are welcome!

[@BJcanal270]

Shukriya Maestro

[@hichamtassi1753]

Salam M Haseeb, if by mistake we short the output voltage why will happen ? thank you & Salam aleikum.

[@HaseebElectronics]

wa alaikum salaam dear brother. i am sorry for delay in current control modification i will discuss in detail with practical it will ready in few days

[@hichamtassi1753]

@@HaseebElectronics Thank you dear brother.

[@masoudjafarzadeh]

Hello When pin 4 of TL494 is grounded, how is the source protected from overcurrent or short circuit? Explain more about this Thank you

[@fatimaKitchen12]

Walkum aslam mashaAllah nice vedio bhai

[@HaseebElectronics]

thanks a lot dear sister

[@rmjnm]

Very helpful.

[@HaseebElectronics]

thanks a lot

[@aksdiyprojects1999]

It's great pleasure to watch your tutorial videos and I enjoy it lot..especially about ATX mods.. I ve a ATX with sh 8110 ic , could you pls guide me how to modify it for higher voltages and higher amperage? Thanks in advance

[@rubentaglienti5528]

Excelente video, es muy didáctico.

[@susantaatha6468]

Beautiful information.

[@HaseebElectronics]

thanks a lot brother

[@alexandroviktorovich3561]

Здраствуйте! У меня к вам вопрос; чем отличаются lm 393 от lm 339. Разница только что ещё два операционных усилителя добавлены, или ещё что то?

[@collinsmugemi8538]

Nice video...just to ask will other pins remain at 5v and 3?

[@mehdi7136]

thanks for this great and very useful video

[@HaseebElectronics]

You are welcome

[@abdulwahid8579]

Very helpful and knowledge able video 🙂

[@broken1026]

Engineer, then how do we variable the amp?

[@onekarim]

The 2 resistors that are removed go to how many volts, my friend?

[@vibinvibi7416]

Sir. Is it possible to adjust from 1v to 20 v

[@HaseebElectronics]

No we cannot adjust any SMPS in so wide range but we can add a linear voltage regulator circuit with current regulator (as LM723)

[@nava-kit]

can you give soldering iron details please

[@HaseebElectronics]

i have Weller WR3M rework station

[@pialpha-s8y]

where do we get 12v power to operate the fan?

[@HaseebElectronics]

that is from 7812 regulator

[@pialpha-s8y]

@@HaseebElectronics Dear sir, thank you very much. Know that your channel has motivated me to pick up my soldering iron again.

[@HaseebElectronics]

it is my pleasure

[@DachaLife]

superb teacher thank you

[@HaseebElectronics]

You are welcome

[@AbdulMomenZargar60]

Salaam Bhai Saab

[@HaseebElectronics]

Wa alaikum salaam bhai Ji

[@techy1661]

Superb n nice upload

[@HaseebElectronics]

Thank you so much

[@Harry001by7]

I did same but not getting exactly, perfect from 9-24 v, but fluctuating below 9 v. Any help ?. Thanks in advance.

[@maurojosequintero331]

muy buen video gracias por compartir, pero como haría con una fuente de ic sd6109 para colocarle un potenciómetro y poder variar la corriente ya que por este medio es muy difícil encontrar información para fuentes con ese tipo de ic

[@esrinibase]

very good video sir. my question , 1. what will be the max ampere of this 12 volt section ? 2. can we make short circuit protection for this device ? 3. when more than 24 volt variable supply is require then what to do ?

[@Studioku971]

Hello mr, vidio yang bagus, saya suka

[@mohammedqutubuddin2338]

Hom much max amps can we draw with this setup

[@electronicaaguilars.]

Excelente amigo gracias por compartir tus conocimientos felicidades

[@akilakeerthisingha3017]

Best to best. All videos are usefull. SIr I need to help from you. Sir I have printer power supply & I try to repar it. Finally struck. My question is.... main mosfet over heart. Output power 24v ok. But in 30sec main mosfet over heat & its gone. Main mosfet control using fuji FA8A86 ic. In main capacitor 305v indicate not switching time. But main mosfet swichin mormet main capacitor voltage drop to 271v. What am I do sir. Comments please

[@HaseebElectronics]

please write the printer model number or power supply board model number so i can reply with some possible causes waiting for your reply

[@akilakeerthisingha3017]

@@HaseebElectronics sir part no is Rm2-8214 thanks for helping me.

[@akilakeerthisingha3017]

RM2-8214 - HP Laserjet Pro Power Supply Board for M130 / M132nw

[@techrama9642]

Whats the reason of buzzing (transformer noise)??

[@nasirmehmood3585]

Can we use 20k potentiometer instead of 10k potentiometer and then with 10k resitor

[@HaseebElectronics]

no it is much better to use 10K resistor and 10K potentiometer if you will use 20K, at full counter clockwise it will damage the PWM controller IC

[@nasirmehmood3585]

Thank you for nice guidanca

[@prangki]

It that the output resistor not burn..??

[@rahulkoley6161]

Plz help me... I already completed these modifications... But the voltage is randomly fluctuating...?? What is the problem...??

[@thevabhas7225]

Very good information.. thanks sir I am just joined..

[@HaseebElectronics]

Thanks and welcome

[@sreekanth369]

Very Nice Video Sir....

[@HaseebElectronics]

Thanks and welcome

[@AH-oe2zl]

Can someone explain why psu is turning off when load is connected? Is that because load consumes more power than psu is rated for? What about normal work? How psu knows when to not cut off power?

[@HaseebElectronics]

almost all power supplies have output supervisor IC, that IC monitors the output voltage for undervoltage and overvoltage and imbalancing between the output lines if any voltage drops, the second line will incraese, thus the supervisor ic will turn off the PWM controller IC in case any output capacitor gets open or short circuited or leaked, the volatge values on supervisor IC's input lines (sense lines for 3.3 volt, 5 volt, 12 volt) will change and it will terminate the PSON interlock to disable PWM drive please consult the datasheet for supervisor IC installed in your PSU's output stage

[@AH-oe2zl]

@HaseebElectronics Thank You for very quick and helpful response

[@FetihFatih-nr6im]

Ve aleykümselam.That's great!

[@HaseebElectronics]

best regards

[@kintushaami4404]

i have a power supply ATX 650watts but it does not have those 2 ICS

[@Chems7308]

I have the same board and success to disable the short circuit protection,but when I am connecting the Pot ,the output voltage is not stable anymore, please help sir

[@mohammadkhalid6886]

Jazakallah khairah bhai ,,,,,

[@HaseebElectronics]

best regards

[@mr.sanjeev369]

Good video sir❤

[@HaseebElectronics]

thanks a lot dear brother

[@taksi.ran2019]

بسیار عالی دمتون گرم

[@kintushaami4404]

Can this trick work on every ATX Power supply? Thanks

[@HaseebElectronics]

this trick makes it variable but the power supply looses the current regulation. so i am trying to add some external linear regulator to provide variable voltage and variable current

[@Yorumcu63]

Great Video.Could you add current limiting feature too ? Meanwhile I am waiting a video about SMPS variable voltage and current limiting power supply design too.

[@HaseebElectronics]

sure in my next plan, to add current limiting feature in the same modification

[@redartps]

Great job bro keep up. Mashallah

[@botelite4817]

Good Job..

[@HaseebElectronics]

Thank you so much 😀

[@fhurqaan]

Assalamumalikum. what is the max current output?

[@kwalide]

JazakAllah

[@aamir8630]

Hello please share link of your solder suction pump

[@msbbadsha1456]

Amazing video

[@HaseebElectronics]

thanks brother

[@pritikanadas3140]

Thanks 🙏 sir it's working.... but problem is it's Mack Sume noise r u sure it's safe... sir...