Brilliant video, so much good information here! Many thanks! 🇬🇧
@rracer70313 жыл бұрын
This is a fantastic video with a fantastic production value! Thank you for taking the time. You've helped me a great deal. Thank you.
@michaelknight28973 ай бұрын
How did you get all your parts so dang clean?
@daves57142 жыл бұрын
Thank you so much for your videos. I’m a life long Corvair person recently acquired a 64 Ghia with a Corvair motor transplant . I’m learning a new language ( VW) & your videos R a great help!
@christianmccollum1028Ай бұрын
That sounds like one hellva machine! 2 extra cylinders for more grunt - I like it!!!
@kathleenvincent79433 жыл бұрын
adding the 4th gasket would create MORE space, not less, thus the play
@joeevans6443 жыл бұрын
Agree
@vayabroder7293 жыл бұрын
EMPI sells a kit of side cover stiffeners that works wonders in making those oil tight. It includes longer studs to install on the side covers to cover the additional thickness of the stiffeners. Well worth it. Always a great idea to (as much as possible) get rid of any dimples around the holes on the side covers and resist the temptation to over torque those fasteners (they go at 14 ft/lbs torque). I’ve heard that the red gaskets are double the thickness of the tan gaskets. You can use both thicknesses to find the sweet spot in terms of axle tube free play.
@josecollazos6 Жыл бұрын
You by chance know the kit name ?
@Mr572u Жыл бұрын
If you are compensating for wear, you remove shims, not add!
@cyprianskiba8768 Жыл бұрын
If your sliding the end housing back on the axle tube, do you have to slide it on a certain position?
@markatr62 жыл бұрын
this doing it off the car & upright is THE way to go! but ive a problem: my seal carrier has no 'wall' to tap the new seal up against, how do i know how far to install it? ive done this in the past & must have just been lucky, cuz i have a BIG leak right now, any ideas anyone? (66 beetle )
@josecollazos6 Жыл бұрын
@vw nerd where did you buy this gasket kit ? You have a part number thanks
@mr.motormaster98813 жыл бұрын
Im your 💯 🎉subscriber🎊 🎈🎈🎈
@mr.motormaster98813 жыл бұрын
Im your 💯 🎉subscriber🎊 🎈🎈🎈
@michaelcarroll948710 ай бұрын
Brilliant!
@leoasman67662 жыл бұрын
When is the next video coming out? I am hoping to see final assembly. Are you putting any gasket sealant between the paper spacers and the plate?
@johncollins5552 Жыл бұрын
No, don't risk that silicone crap getting into the gears. Make the sealing surfaces super clean and flat. Only use a smear of rubber sealant as used in pucture repairs around the end of the axle tubes when you put the rubber boots on.
@dustynmccloud58463 жыл бұрын
Can anyone here help me out here I recently baught a dunebiggy with a seing axle tranny that was bad I changed the tranny with a used one but this one is leaking in between the tube and flange that holds the tube on its leaking into the rubber boot any fixes or is this internal leak?
@josecollazos6 Жыл бұрын
Did you figure it out I’m having the same issue i just bought one also and it’s leaking as well