Reviving my dead Coleman !

Рет қаралды 21,238

JMMJ Productions

Күн бұрын

Пікірлер: 59

@chucklynch100 5 жыл бұрын

May God send multiple blessings your way 👍🏿👍🏿👍🏿👍🏿👍🏿🌟

@JojoCano-ix9cu 8 ай бұрын

Thanks for the knowledge...the emulsion tube 👈..👍

@skypilot23 Жыл бұрын

after sitting over winter mine would only run for 1 second, seemed flooded. If remove the plug, wait and try again same thing. Replace the carb and nothing. Changed the plug and runs perfect. Always try the plug first!

@bigmanracing300 4 жыл бұрын

Ethanol gas turns to varnish quick without fuel stabilizer almost like glue . I recommend stabil in your gas.

@anthonyderose6069 Жыл бұрын

I had a no start on mine, after sitting for a year. I cleaned the carburetor,and still wouldn’t start. I checked the engine compression and had no compression. Pulled the valve cover off and found a stuck valve. I sprayed WD40 on it and tapped it with a 1/4” extension and small hammer. That did the trick.

@Jcorpus02 Жыл бұрын

3:25 where did that little thing come from? I didn’t see from where you took it out from

@Jcorpus02 Жыл бұрын

I’m having the same problem. My Coleman wont start and I already checked and everything was clean

@6bettyboo9 Жыл бұрын

It called the emulsion tube and its under the main jet. When you remove the main just it will most likely fall out. Unless its really gummed up.

@kerrygatling663 5 ай бұрын

@@6bettyboo9 What the key to getting those jets out it's like a one-way deal were their only a slot to screw them in?

@cheesebandit84 4 жыл бұрын

Old spark plugs are good for stopping hoses from leaking

@jeremyhurd3500 Жыл бұрын

Thanks for the tip

@ge0ne063 2 жыл бұрын

My mini bike worked perfect, had it in storage for about 2months, runs only with choke on Bought new carb after cleaning the old one that wouldnt work....new spark plug and still wont run. Fuel tank was cleaned and its flowing good. Only with choke open 🤔 it stays idling

@6bettyboo9 2 жыл бұрын

Have you checked your valve lash ? If it runs with the choke on its somthing simple .

@troyholland3436 Жыл бұрын

What do you recommend doing to make my ct200u go at least 35-40mph with the jack shaft? I would put the straight chain on but it just wears the clutch out way to quick

@SeanBulicki 6 ай бұрын

What did you do cause I’m trying to do the same thing

@troyholland3436 6 ай бұрын

@@SeanBulicki I just straight chained mine bro it it went over 50 just there’s a screw for the throddle I’d remove not the internal governor but the throddle one and if you got the stock rear 50 tooth straight chain it’ll go at least 45-50 but won’t have much torque you can always keep the straight chain and put a 60 tooth on the rear it’ll have decent torque and still do at least 40

@troyholland3436 6 ай бұрын

@@SeanBulicki and another thing make sure you have good tension for your chain it’s definitely important when you do the straight chain to not have it loose you definitely want decent tension of course not too tight but pretty tight so it doesn’t come off

@KayBuddha 2 жыл бұрын

What spray you used

@kerrygatling663 5 ай бұрын

Anyone knows if the BT200x have that same carburetor as the ct200u?

@Next2TheMoon Жыл бұрын

"When you pull this off it's going to drain the tank..." Or you could just plug the line lol

@natashaspeir5775 3 жыл бұрын

Had same problem I just clean out the carburetor

@lacarti_4L 2 жыл бұрын

Hey I have the same problem ima take it apart and clean it but do you know would the gas come out the cord because I’m hesitant because I have a full gas tank lmk please

@6bettyboo9 2 жыл бұрын

just make sure you fuel valve is off . or you can pinch the line from the tank with vice grips .

@lacarti_4L 2 жыл бұрын

@@6bettyboo9 ty also do u know if Coleman can’t start with out the spring next to the engine bc I don’t have one all I have is the little metal pole by the filter

@6bettyboo9 2 жыл бұрын

@@lacarti_4L yes that little spring is important to will not run right without it.

@lacarti_4L 2 жыл бұрын

@@6bettyboo9 thank you

@SpaceExplorer4430 3 жыл бұрын

Do you ever have problems with the Chain? How often do you need to tighten it?

@6bettyboo9 3 жыл бұрын

Rarely actually only once since 8ve owned it . But I keep it pretty well lubed.

@SpaceExplorer4430 3 жыл бұрын

@@6bettyboo9 Really, for me both of my Coleman ct200u's always needs the chain tightened.

@natashaspeir5775 3 жыл бұрын

Mine is a 2020 model and it had lots and lots of chain problems for no reason

@SpaceExplorer4430 3 жыл бұрын

@@natashaspeir5775 Always getting loose I bet.

@Gigachadly 2 жыл бұрын

@@SpaceExplorer4430 then you obviously don’t have it tensioned right. Try losening your rear wheel, pulling the tire until it’s as far back as it can go with the chain being tight, and tighten up the bolts again. That’s what I did and my chain never comes off no more

@gerohansalas9046 4 жыл бұрын

mine started rite up this morning rode it for a long while turned it off went inside for a while came outside to ride and it wont start now any ideas? another thing what oil do u use on the coleman ct200u?

@ColeDuarte-tl9jl 4 жыл бұрын

10w30

@sedrickkeener2677 3 жыл бұрын

Yes it is because of the fuel pin in the carburetor, just google (carburetor fuel pin) and buy any pins bigger than stock fuel pin!

@YugiKards 3 жыл бұрын

How did you remove the tube?

@6bettyboo9 3 жыл бұрын

Remove the pilot jet and the emulsion tube will fall out.

@williamcrazylacyfurmage9953 2 жыл бұрын

@@6bettyboo9 darn it, I just had mine all apart and did not mess with emulsion tube. i just sprayed with carb cleaner only, added some premium gas to the the gas that was just 2-3 months old and it runs better, but just falls dead and stalls at times.

@samuelheg6745 3 жыл бұрын

I did everything and checked everything what else could it be it wont even start up with the choke

@6bettyboo9 3 жыл бұрын

did you pull the jet and emulsion tube ?

@Mullenvtheworld 3 жыл бұрын

When I start mine it makes a weird noise and when I crank the gas it doesn’t do anything but make more noise and goes nowhere

@whereswaldo5740 Жыл бұрын

You need to put some oil at each end of the clutch. Need the crankcase there’s a thrust bearing. Put a drop or two there. And at the outer most end of the shaft between the clutch and the big washer on the end. I put a drop the spray a little WD40 to wash it in then another drop. If your sound is a screeching that’s what it is.