7 Channel

[@JHEpon]

I don't know why people do not view this videos...awesomee👍👍👍

[@raheelkhan9518]

My dear, for watching only video, this video is perfect. But for implementing its not good. You should explain the parts also. All parts.

[@camplays487]

@Internet Gamer'z 360 that’s not an explanation, its a list

[@x-6790]

don't talk like idiot

[@naola6456]

Excellent project. But I'm unable to download the schematic diagram, it's not found!

[@natheerkhan7955]

Thanks for your clearly explanation But I have a question. If I can use a lora module for more rang.. And what is best module that provides less time delay

[@guptarahulsunil2149]

Can you plz provide rotary encoder switch link and which type of rotary switch we have to take plz replay Asap......,Thank you

[@ranjeetchhajer49]

Please tell me all over total budget for this project

[@surajsingh-wb5wj]

What rf module will be use if want to increase the range and libe streaming camera also

[@EtDiscover]

Next episode

[@dhanashreetodkar9556]

If I make this then do I will need KK flight controller to control drone?

[@gilreis5807]

Your Gerber is in error !! In the transmitter 5 volts it only arrives in the regulator 3v3. If using the AMS1117 3.3 you do not need the 1K resistor. The 10K resistor is also missing from the processor reset, both from the transmitter and the receiver. Whoever orders the plates will see that they do not work.

[@rachit_25]

What should i use from ur list provided in description if i want to make only 4 channel transmitter nd reciever ?

[@nimeshsuriya9035]

I like to use transmitter control via Bluetooth control in mobile, what type of board can I use, please give a good suggestion.

[@princebadboy12354]

What should you do with these diy projects after making these projects can you tell me about this

[@_titasroy_]

From which state you are

[@suhas.esuhas.e8349]

Hi, sir in this drone use camera to fit this option is available

[@bobbarinagaratnam6033]

Excuse me ....can you tell me which couse did you study to know about all this stuff

[@tawandamunyanyi2810]

this is good work. can you kindly share your schematic diagrams sir. and if possible your code fro this demostration . the link in the description is broken i guess. thank you

[@hsmusicfr]

Please explain the programming part with normal arudino not your homemade

[@shlokpandey2463]

Can we use it as flight control board for brushless motor drone

[@venkatesanjayaraman2987]

Please sir tell me where is it possible for me to dtmf and 2 mobile phones and use it as reciver and transmitter

[@darshandongare4359]

Can you please make one more transmitter and receiver but of 14 channel. Bro please make it we all are supporting you . Please please please . This was very nice and beautifully made . Your videos are awesome . Please make it

[@shamimahmed-ux4jy]

Can we program ic with arduino uno ic socket by change this ic plzz tell

[@thetechworldbysoumen4274]

Brother i can not understand the s1 to s7 connectors or header pin purpose. please explain this. And if i attach a coreless motor with j1 header then dose it works??

[@EtDiscover]

This receiver only for brushless motor Not coreless , This Receiver just produce sense

[@rustom767]

hello, thanks for this video i made the transmitter and receiver and their is a connection between them but i have a problem no channel on the receiver is resetting to 0 for example if i connect a led to a potentiometer CH the led doesn't turn off if the potentiometer is all the way down but i can increase the brightness of the led when i move the potentiometer up even servos don't move or the motor on esc ,i can control the throttle but not turn it completely off. the same happen with switches can't turn of a led but can increase brightness of led when turned on. please if you have any idea tell me thanks in advanced :)

[@CalvinSJ]

Can we use this reciever for brushed motor drone Please reply

[@EtDiscover]

No

[@CalvinSJ]

What changes should I make on the reciever for making brushed motor to work

[@PradeepKumarVelidi2002]

yes

[@mrtechsavvy8835]

If I use this for making a quadocopter then I have to solder the accelerometer on the transmitter board???? Am I right ?

[@dertutorsdersaurabh2170]

I was trying using nrf24l01 module with arduino, but could not communicate between two nrf24l01 module. Please make a video to live demonstrate how to use nrf module with arduino mega/nano from very begining level

[@Cyberdyne_research]

Wait… you’re offering the gerber files for free?? Bro you are my hero. I’ll donate to you In a little while. Ty so much.

[@aaryanpatil9213]

I want to make one but I am making PCB at home and when I create schematic ,and tries to convert in PCB it says incomplete nets. Please help.

[@harrishdhakshinamoorthy5383]

Google drive link is not working bro Plz help me with it 🙏

[@damo690]

Hi. I wonder can you help me. I have a parrot skycontroller for my drone. It is a wifi controller. The function for up down has stopped working. Controller connects to the drone and all other functions work. I can only assume the control chip in the joystick is gone bad. Where might I find a new chip to replace this? Parrot are of no help to me on this.

[@amankumarsharma1672]

Which camera you used to make videos

[@kahosheshohe1320]

Can this work with unchangeable batteries ? Please reply

[@prasantaadakdcst3411]

How to setup Elevon Mixing (channel 1 + channel 2) for delta wing plane like f22 rapter,delta wing?? plz reply my question answer 🥲 in this transmeter and reciver

[@sunitasharma8938]

I have only Arduino uno board can I directly connect it with transmitter for uploading the code . If yes then how?

[@hassannawazish9300]

We can't make make using NRF24L01 because there are some issues with range.

[@EtDiscover]

If you make it perfectly then there is no issue

[@hassannawazish9300]

@@EtDiscover NRF are good for RC boats cars but in case of planes if planes go out of range there will be a crach.

[@gersonmoura6634]

Hi, how did you modify the joystick potentiometers? Thank you!

[@knowledgegyaan4778]

Sir your google drive link is not working please provide me a correct link i am also making a drone so i need this Tx and Rx

[@paragmore7887]

My nrf24l01 attena module is not working properly .please give me suggestions 🙏🏻🙏🏻

[@prasantaadakdcst3411]

Plz make a channel mixing (2 servo) ( channel 1 + channel 2) module circuit

[@nothingmuch2323]

how to program IC without ur that programming device

[@EtDiscover]

You can using Arduino uno nano as you want

[@pandrocutz9691]

@@EtDiscover how

[@pravanjantripathy7345]

How to make a electronic robot which operates the programic logic command.please basic training in robotics video.

[@akerman1345]

Hlo i cant order pcb using jlc pcb because i am from india

[@nicktube8637]

Is this transmitter compatible with Whoop Lite F3 Mini brushed flight controller

[@martinnovotny6737]

Hello, I like your project, but since I am a beginner, I would like to ask. I need not only to send, but also to receive battery status data from the receiver. Unfortunately, I can't adjust the program to make it work. Can you please advise?

[@alphayt6434]

Which programmer modules did you use please?

[@universeofcubing3736]

Can we use a coreless motor in this

[@ylmazgumus2641]

Hey bro what is the menziles? This transmitter

[@rva1945]

I couldn't make that work. I used two Nrf24L01+ but I only got 1 packet received in 10 sent.

[@ExtcWorld]

Sir i am havin a rc brushed motor mini quadcopter and i lost the tx, the drone is build with stm32f031k4 chip with xn297l radio chip, so i want to control that drone with ur diy tx, is it possible?

[@SIKHGT650]

Hey , I have already made it few days back but throttle joy stick is little tricky, did you modify it ? I have excluded spring so It can stays in same position.

[@EtDiscover]

You need to change Value of millisecond

[@parshvapatel8484]

preet charan what will I have to study to make this mu higher education

[@SIKHGT650]

@@parshvapatel8484 degree in electronics

[@apoorvdeepak7333]

Kitna distance cover kr skta hai yeh drone.. Aur age range increase krna hoga to kya krna hoga. Yeh bhi batiye na..

[@onikislam6693]

Where can i buy it? Can i get from International shop

[@rohitgujar5072]

Sir where can we get the programming?

[@anirbanchatterjee835]

please describe about the "rotary encoder"(sw1) in your ckt. where you have placed the potentiometer....can you give a link for the potentiometer?

[@buggsbunny4990]

6:07 to 6:12 what you exactly did here?

[@vishalmhatrevishal]

Can u make same concept for camera input and output purpose

[@deveshbharti7684]

Pls give information about all the components of receiver boarx

[@mohammedasadbubere6519]

Sir please make a rc car and interface this remote contoller with it.

[@random_guy1024]

GERBER file is not accessible. Can you provide a valid link? link in the description is not working.

[@abhishekrai3342]

How did you solder?

[@abhasharma5386]

brother your pcb pdf link is not opening please tell me another way

[@abhishekmeena4634]

Cant you provide any circuit diagram for transmitter and receiver??

[@sunitasharma8938]

Can you plzz give me the link of desired transmitter and receiver pcb board which you have asked from jlcpcb ..

[@Ankitkumar-tb6vi]

Can we increase the range and the no. Of channels??

[@VIJAYMOGILI]

where you got that components pls give me link

[@akerman1345]

How much volt did you used for reciver can we use 3.7v

[@kartikbhargavapsd]

Can I use it for flying drone . ??

[@anirudhkundu597]

can this be made with STM 32? STM 32 has better ADC resolution

[@netrapatil2169]

bro i want to learn electronics of your level what should i do..which course..

[@EtDiscover]

I make a separate video for this please wait

[@netrapatil2169]

@@EtDiscover ok bro.Tq

[@yxhankun]

I cannot open the both sketches... error is could not create sketch. I am using windown 7 32 bit. Can u post the sketch in *.txt format in your download else i won't able to learn anything. Please!

[@whitedevil-io2cr]

Can i connect brushed motor to this

[@vikevignesh4541]

Awesome work bro. I already have a 2.4Gh remote that came with cheapest drone I bought(Hasten 720) . Any idea to DIY a receiver for that?

[@APOLLOALPHA6685]

Bro your transmitter and receiver code which you have put in the description is not opening so what should i do

[@ShaktiSwarup-np8lz]

Sir, what is the range of trancmiter and riciver

[@TechKiClass]

How can i make it

[@tanushmaurya3388]

Can u make a racing drone using this transmitter and receiver

[@afranioafranio2]

Excellent work!!!

[@gunildrokhoirom4013]

From were we should order all this things

[@sadiqabubakar7164]

Please how can I get all the exact electrical Components for the project such as capacitor resistors

[@nagendrak1037]

Namasthe sir I like this but put name of components plz and what's that Hindi channel name plz reply I interest lot plz

[@TristanYT1]

Please try to make waterpump from old Brushless dc motor

[@fahimmia738]

How to buy is jlc pcb transmetter board...? in bangladesh

[@miteshparmar1863]

How can I get ready-made PCB, from online or other sources...?

[@dr.renukasingh9547]

which switch i can not hear in trans mitter

[@techpinak]

Can i program microcontroller ic using arduino

[@EtDiscover]

You can

[@sangeetagupta6776]

It can control fpv camera with drone

[@prakash580]

Sir , circuit diagram link not opening,give me circuit diagram plz

[@protonrc]

How to prevent the interference between the receivers?

[@bobbarinagaratnam6033]

Can you tell how did u know about all this

[@akshayverma123]

Can you help to make mobile phone as a receiver??

[@SumitSharma-do8ye]

How many metre done by without antena module

[@quoctoan4437]

PCB on Easyda ?

[@electroindia1008]

What are the 2 pin male header on the receiver for?

[@nahid5566]

Bro where did you buy all this stuff in kolkata....?? Can you share Shop location.....it would be helpful...

[@EtDiscover]

haque electronics kolkata

[@nahid5566]

@@EtDiscover chandni chowk.....???

[@EtDiscover]

Yes

[@SumitSharma-do8ye]

How many metre it can recieve and transmit data

[@saqibsanadi5648]

Brother I have a big problem, my esc and servos connected to it also start moving when I shake the receiver can you please solve my problem what may be the cause for it some times when I shake the receiver or just move it the servos and motor just start moving even when the transmitter is off

[@danocruelgaming1538]

how to program ATMEGA328P SMD with bread borad

[@manbox866]

can you pleas tell us how to configure mpu-6050 3 axis module in this transmiter to controol drone

[@kevalpatel9395]

Can you give me the details about potential meter

[@aryabhattanu2450]

Please make video for designing an esc

[@ryanranawaka4164]

Where does The ANT wire go