Easiest Way to CUT TILE Around a TOILET!!! Tile Coach Episode 29

[@SalDiBlasi]

Isaac, put the guard back on that grinder, I have seen pieces break of those blades and fly straight at the person using the grinder. Had it happen to me, but the guard stopped the piece hitting my face. . I cringe when I see that.

[@JeepMurphy]

guards are for sissies.

[@markme4]

@@JeepMurphy guards are for smart people

[@JeepMurphy]

@@markme4 eyes roll..............

[@codybersicc7939]

shut up

[@islanddan4302]

I’ve had mine on for years. Recently took it off , but only because these blades won’t mangle your hand like a metal blade. That being said I never considered the blade breaking apart I may need to consider putting it back on.

[@rickcavtube]

Good vid. I know it's not part of your tile-cutting thing, but still worth mentioning something very important to the viewers. You have now raised the floor by the thickness of that tile. And a toilet flange must always sit ON TOP OF the finished floor. Therefore it is imperative to install a small flange extender (there are many kinds available) before installing the toilet.

[@ramsesvega5066]

That’s not completely true, I’m a licensed plumber and is not even a code here in fl

[@jackpine4347]

That's not always true. I did a couple of American Standard toilet installations and quickly found that with the flange installed on the tile the toilet was actually a bit too high off the floor and needed to be shimmed up quite a bit all around to get it to not rock. I recently pulled one of those toilets and installed a new tile floor over the existing floor, and left the flange as is. The toilet now sits perfectly seals just fine.

[@craigsmith8320]

I had this concern and had a pal tell me to just put a second wax ring on and not to worry about the height that the tile adds; is that a good idea?

[@1984mrdale]

Just get a “better than wax” kit and you don’t have to worry about height as it will set you up for any height.

[@d0nn13m0n0]

@@craigsmith8320you can buy wax less gaskets, thick wax rings or stack wax rings. It’s all fair game.

[@telsonboy]

This is one of the best presentations I've seen. Clearly spoken, clearly explained, clearly demonstrated! Bravo!

[@cas3proven]

As a plumber, you want the flange of the toilet on the tile, not same level of tile!!! This is the number 1 issue that renovators do, a classic bathroom remodel with no real plumbing change so a plumber isn't called in because there's nothing "complicated". The tile flange has to be minimum 1/4" above tile. The toilet wax is for odors, not water so what happens is the toilet gets installed and no water is noticed because no issue until 6+ months when the wax has worn away from the flushing and water starts to seep on the side and ruin the subfloor over time. Please, tile under the flange!!! Worst case with a plastic flange you can get a flange extension (not perfect but better than nothing). Remember, 1/4" minimum above tile to create proper toilet seal!

[@cas3proven]

@Bryan Bolden not exactly sure what you're trying to say.... the flange of the toilet should be installed ON TOP of the tile, you never cut the tile to go at the same level as the flange... really not sure what you're trying to say but what I've explained is in every building code that exists, it's in all the literature that comes with every single single toilet you purchase. So, without having fully understood what you're trying to explain, I'll just leave it there.

[@cas3proven]

@Bryan Bolden I'm a contractor, carpentry, but mainly plumbing and heating... when you're doing a job, the tile guy never thinks about the plumbing the way a plumber does, to do it properly, you need a plumber to REMOVE the toilet flange completely so that the tiles can be redone properly and only THEN does the plumber come back and install a flange. Every single time a tile guy who doesn't think twice about the plumbing comes, removes the toilet (because it's isn't rocket science) and then tiles, and then reinstalls it... every single time a plumber comes back 6 months later "my toilet is leaking... why?" because the toilet flange is not sitting high enough, the plumbing job was so tiny, the tile guy or handyman took it upon himself. When I worked for insurances, this was #1 problem for water damage. A simple retrofit/revamp renovation that turns into water damage in the future. And even now, I get a call at least once a week about a leaking toilet... THIS is the issue. I tell all my tile guys and other contractors to be mindful of this because I've dealt with it and continue to deal with it on a weekly basis!

[@EMC3Darts]

​@Bryan Bolden Michael Dubois is trying to say that the bottom of the flange (the lip) should be the same height has the bottom of the toilet IE the same height as your finish floor that the toilet rests on. This is to ensure a 360 degree solid seal against gas (and water) with a common wax ring. Rarely is that the case unless you plumber comes back through. It most definitely isn't the tile guys job. But the thing here is that there are flange extension kits and many different toilet sealers beyond a wax ring. Some of those various kits have extra pieces to add spacing just for recessed flanges. This issue might have been more true 20-30 years ago but this particular problem has come a long ways with easier solutions than resetting a flange. In new construction the plumber is supposed to know what the finished floor height is, set it and move on. The tile guy has little to do with drains. For the cheap man jumbo wax rings are a thing now days, they are much taller to accommodate for these common sorts of errors. Mike is right, this is super common in old houses, but it has been out thought a dozen different ways. Still it does need recognized if you are going to seat a toilet. Usually not the tile guy's thing.

[@somedudeRyan]

Looked on the comments to say exactly this

[@TheDajjman]

I’m a plumber too. A properly installed Closet flange extension is perfectly adequate.

[@joym5109]

as a tiling beginner, I appreciate this video. the octagon cut worked amazing!

[@angrypops897]

Go girl hard on the knees 4SURE lol

[@jtackett99]

Dude, your videos are amazing! I've been slowly going through all of them and I can't thank you enough for all your detail and most important....your honesty and integrity!!! It's very hard to find guys like you in any industry! Thank you for everything you do!!!

[@nickreichenbach]

Awesome instruction for a middle-aged dude about to tile all kinds of rooms in the house. I have to say, the last two minutes need to be played in every high school orientation.

[@charliebrady3751]

Thanks so much for making those mistakes, so we don't have to. Or at least not so often - I just spent yesterday tiling a shower surround, and today ripping it out 'cause the tiles weren't well bonded. But without KZbin, and people like Isaac, I wouldn't even have been trying to tile my own bathroom. Lots of love, to all sharers!

[@robertamaya4720]

Isaac, tomorrow I will try to do the circle cut. Thank you for showing the way. You made seem simple. I know I will challenges but with the help of experts like you, it makes the job easier. One more time, thank you amigo

[@erickmonge3632]

You're awesome TileCoach. You have a genuine desire to transmit your knowledge. Always great tips, greats vids. GBY

[@gabrielespinoza5060]

Thanks....you are awesome. I been in the floor industry for 16 years. Now i started doing showers and do them as you teach. Other tilers i know think they know it all and i can see all the corners they cut. Thanks to ur videos. I want to one day be able to do all that great work you do. I started doing residential carpet, then moved to commercial vct,lvt etc. But i enjoy shower work much more. Thanks again and keep up the good work👍👍👍👍 by the way i also want to add that you, sal deblasi and landberg tile are myrole models. I only do work as you guys show.😎

[@julievaisey8765]

I have never tiled before and was very intimidated by cutting around the toilet flange. Your video boasted my confidence. Octagon for me. Thank you

[@tomboyle2776]

I've been doing this for almost 25 years now. I've never even thought about feeling the Octagon pattern and always went with the circle cut. Bro, you totally blew my mind with that shit. Thanks for the video and keep up the good work. I'm from Jersey. We don't do mud walls around here, LOL. Unless it's a super. High end job But it's a lost art and you have a gift my friend. God bless

[@davekyle6096]

Oh my! Great video and raising $ for worthy causes. Hats off, young man!

[@greggmiller4739]

Your the BOMB Tile Guy !!! I started out using a four and a half inch continuous diamond blade. Two times towards the end the tile cracked. I purchased a four and a half inch diamond mesh blade and I had absolutely no problems. Perfect circle on the first try. And yes I'm a rookie these are my first tile jobs in the house and I have two more bathrooms to go. Thank you much for your informative videos. No way I could do this job without some of the tricks and tips that I watch on your KZbin videos !!! And I'll save at least $2,000 on three bathrooms versus hiring a Tile Guy like you. 👍👍👍👍. Thanks Again

[@MadMax-ht8iu]

Hi, you are a thorough professional and today you did say to get educated first and then find a trade. Education is very important to lead a life and a profession to live a life. Thanks

[@dubmasterz3261]

Thanks for the knowledge and the honesty in your own story. Glad you’re a good tile coach.

[@orbitring]

Nothing like an experienced Craftsman to learn from. Great video and very logical to follow along with. Thanks TileCoach !

[@CAMPFIRESKY]

Exactly the video I was looking for. i'm sold on the octagon approach for sure. THANK YOU !!!!

[@jimgetek2017]

I just started watching your videos. With 45yrs exp. I must say you are awsome!!. Keep up all your good work. Want to note about not useing the gaurd. I know that there a danger with not having it on. But over the yrs its proven to only limit an get in the way of alot!! You should always with eye gear on, or a full face shield if concern about flying chips. Maybe you should do a video on the pros an cons on the gaurd.

[@milagroshampton7932]

You are such a awesome young man. I hope all the blessings come to you.keep up the great work.

[@JoseHernandez-im4wz]

The octagon cut is wonderful bro. I Love it.

[@RELAXnRENOVATE]

Metal toilet replacement flange covers are cheap and a great thing to have in your work trailer for a template. Then you can draw a perfect circle to cut. Great job and great video. You're killing the tile industry, Isaac.

[@joeSmashman]

Yes indeed I use the toilet flange as a template all the time!😁🤙🏻

[@RELAXnRENOVATE]

@@joeSmashman great minds think alike 😜👍

[@billybrey2067]

Well done! You seem like a genuine human being!

[@polinasayess965]

Octagon seems way easier and just as good as the circle. Well done! Thank you so much for the demonstration!

[@richardordonez8331]

As a plumber, what we appreciate is that there is side to side support for the base of the toilet. The front and back could have large gap since it won't interfere with our installation. However, fill it so when the wax fails, the void doesn't fill up with water and get under the tiles.

[@loulu8179]

Isaac - love your stuff. It's real. Don't let the trolls get you down. After watching you place the 7-1/4" blade and trace around it I wondered why you just don't first draw the circle and then use your speed square tangent (just touching) the circles at 45 degrees. You wouldn't have to measure out the 2- 3/4" (which theoretically is 3.003). Also like your cutting on the Kerdi - great idea. I hardly ever comment but the trolls were getting out of hand. Keep it up and thanks.

[@petrhermanadventures9509]

I started setting tile 20 years ago and used a grinder without a guard too. I put it back on after I nicked my finger and in the last 15 years I have not encountered a cut that I could not make because the guard was in place. So not using a guard is insane, yet many tile setters do it.

[@TheHeavyend81]

All these years of tiling and to use an old saw blade to draw a ragged hole, surely by now you would have had a simple circular template handy to draw a nice neat circle, especially if used repeatedly. But great videos and I love watching you work. I have to second the comments about the blade guard. A friend of mine lost an eye due to cutting tiles without a guard. Watching this practice makes ones bum fizz.

[@trevormaclean7916]

I always tell my self I'm gunna stop trying to cut so tight around flanges and just cut octagons but I always end up wanting to cut a perfect circle it just feels better for my o.c.d lol

[@paulrosenbaum1678]

Hot tip from someone who just did it for the first time, while the octagon looks easier the circle is better because the tile is less likely to break. I broke 3 tiles doing the octagon then finally completed a circle with the same tool, same blade, same inexperienced me. I think it must be just a better shape.

[@michaelbacile8439]

I do almost the same thing. We keep one of those toilet flange blanks on our truck, so after we measure out the square we simply put the blank in the square, trace it and cut it out 1/8 larger than the blank. I can see how cutting the straight lines would be faster than grinding a circle. I’m going to modify my method mixed with yours next time and see how that goes

[@craigsmith8320]

How’d it go?

[@fador85]

Hey Isaac new viewer on your page. I'm a general contractor in Washington State. Started seeing you use this product called Kerdi that I've never heard or seen before., Just use it on my first bathroom to do water testing. I am simply amazed and Blown Away by how easy the product is to use. Thank you for your time and advice!

[@chrisgraham2904]

The octagon cut works just fine, so need to cut the circle. The octagon also generates less than half of the dust that the circle does. The octagon straight cuts also stress the tile far less so the chance of cracking the tile is minimized.

[@vincearanda197]

I cant stop watching your demo dude,,so great and very intelligent,,

[@kcordes3]

Great job coach! DIY people will all benefit from this video! Appreciate the help!

[@csimet]

Good tips here. I prefer the hex cut method myself, unless the hole is less than say 1" from an edge. I may do a partial circle along that side so there is less chance for a break. Another tip, if I may... since the toilet flange is supposed to mount on top of the finished flooring (best practice is on top of the tile, not below or flush it as most people show), I cut my opening like you show and use some left over tile pieces to shim up below where the flange will sit. Just place the tile pieces between the screw holes when you place the tile and use grout to hold it place. Best to make sure you have grout under the screw locations and not the tile pieces or you will have "fun" drilling those holes. ;) Makes for very solid install and little chance for leaking. Another advantage is more grout coverage below the flange at those mount holes round the base you could silicon to make it basically water tight.

[@MICHAEL-wq8mk]

Awesome! Have always spent time cutting "perfect" circles for no reason! Thanks for the tip!

[@jimgetek2017]

I like the octagon idea. I also carry a flange in the truck for easy marking. But i love to save time.

[@BZ1340]

I keep an extra flange in my supply box I use for tracing

[@reeze7564]

yup go buy one

[@leviledbetter]

Smart dude

[@KTSLAY]

🎯

[@EMC3Darts]

@@KTSLAY I use a roll of tape for most circular cut outs. It is great for can lights. If you have need for a tinier hold, use the inside ring.

[@greggmiller4739]

I just used a compass and made three 7 1/4 inch cardboard circles. I only have three bathrooms to do is I'm not a professional but it's worked perfect so far and only took me 5 minutes to make them. 👍👍

[@LandbergTileTV]

Love the skill saw blade for the circular template. We have plenty laying around, cool idea!

[@tomboyle2776]

Yes. That was an awesome idea I never thought to put those two together. By the way love that last bathroom you did. You just had to show off with them glow in the dark golf balls. Haha, LOL. Nice job, bro.

[@tomboyle2776]

You could always use an old wet saw blade and just go a little wide on the pencil Mark.. Don't have to worry about the saw blade teeth getting in the way. But great idea nonetheless.

[@justinofboulder]

I keep an old redguard (1gallon) lid...it's slightly oversized but works well

[@justpassingthrough7989]

Or..... Just buy a closet flange to keep in your tool box. Then angle your pencil away 1/8" when scribing around it. 👍👍👌

[@billzima7068]

Keep the plastic ring the blade comes on. Little bigger then the blade but perfect for a template. Gives you a little wiggle room as well

[@davidscadlock5569]

THANK YOU!!! GREAT DEMO!! TILE AROUND TOILET IS TOMORROWS PROJECT!!!

[@eithandudnik4416]

I've done the hex & it worked like a charm, thanks a lot for your video

[@Heb101922]

Isaac, I use a toilet flange that I bought just for this purpose a little over 3 years ago. I keep it with my tile tools and when I need to cut a hole for a toilet I locate where the cut out will need to be and use it to mark the tile. The octagon is a good idea too.

[@corriedf]

Great video. Very organized and helpful. Thank you for sharing.

[@pammcguire4191]

Extremely helpful for me. I'm just a DYI-er. Great tips.

[@emk7132]

This was so helpful! Thanks for taking the time to put this together for us! Also, really liked the comments at the end about working in the trades; so true that many of us can find satisfying work here and college followed by days behind a desk is not for everyone!!

[@douglasdailey5998]

I kinda like that octagon cut , i have always cut a circle for over 25 years . I'm going to try the octagon way on my next toilet cut.

[@eslibravo9862]

Thanks for the coaching on this ! Definitely sped up our last two bathroom floors!

[@choimdachoim9491]

Most of the bathrooms I've tiled have been with smaller tile so I've only had to cut a few enclosed circles. I did it by using a sacrificial-wheel that had worn down almost too small to be useful but was perfect for cutting vertically around the perimeter of the circle. As respects a comment below, I've replaced many toilets and often the flange is screwed to the subfloor and not installed on top of the finished floor. Some of the homes I worked in were plumbed with cast iron and I'm not going to bother changing what I found. Double-stacked rings is a viable solution.

[@Maidiac]

That's funny. I too started from college 31 years ago and decided sitting at a desk was not for me. On topic I usually cut the circle. Have extra flanges in my plumbing supply box.

[@scflooring8658]

Great job I keep a new spare toilet flange in my van to make my toilet cuts or a paint can lid works also. But I like the octagon cut and it saves time too!

[@ihishey]

Thanks for teaching us. Watching you from India.

[@felipepena2401]

Thanks for sharing this video. It's helpful to see two different methods and then choosing what works best for us. I also liked the explanation of the grinder blade differences. Very helpful

[@sallydoe6638]

Thanks so much for a very informative video. As a mature adult home owner, I learned a lot coming from the point of view of plumbing. (I am a novice plumber!)

[@TheFatman2436]

Soh two heavy weights of the tiling world have commented on your video Sal diblasi and landberg tile where is that Mr know it all 🌟 you know who I mean great to see fellow tile professionals taking an interest in each other 👍👍

[@notsure103]

Learning the circle is important for exposed drains. It doesn't really matter for under toilet but what does matter is code. Flange goes on top of finished surface.

[@frankolivier3454]

Nice job on both! I prefer the circle cut.

[@bradnelson3053]

I used this method today and it worked out awesome. Tank you.

[@tchotchkegirl8880]

Thank you for all your wonderful help. You have made my life easier. I am so happy to have found your channel. My nightmare bathroom project will turn out beautiful. Universe Blessings!

[@bryanpeart]

great vid man. Definitely will use the octagon from now on.

[@TheDadofsix]

IMHO the straight cut is the way to go. I am a perfectionist which means I spend inordinate amounts of time trying to make things look perfect. You mentioned it: no one will see it except the plumber or the person changing the toilet ring. I am weening myself away from absolute time wasters that add no value. Thanks for the video

[@frankflores5931]

Nice job brother. Appreciate you sharing from your experience. Us DIY'ers can always benefit from tips from the pros. Thank you.

[@joeshmoe8912]

Isaac that is so cool you use the circular saw blade to mark it. I always use the plastic covers that the blade comes in but never thought to use the blade itself. Thanks for sharing tile coach.

[@tomfarkash6446]

The octagon cut is the winner and you explained it very well why. You are an excellent tile setter, installer and an excellent teacher. Congratulations!!! I am very glad you are on KZbin.

[@jefffarage2083]

Great tips coach. Like you said it’s hidden by the toilet and with the new wax rings with the rubber seal you have no leaks and no worries

[@midnightgardener8346]

Thank you. Having to completely tear out the sub floor in my bathroom right now and this is just answer to the question Ive been asking my self all day. Think I’ll just leave a riser and put the flange on last.

[@kurtdussander4944]

It’s better to put the flange on last above the tile instead of cutting a hole. I wonder how many people cut out their tile after watching this video, anchored the flange down below the tile and now regretting it because their toilet sprung a leak.. Spacers work too in such a case too I suppose.

[@appalachiansam8280]

Thank you for these videos! You are awesome at breaking things down for anyone to understand. I am remolding our 4ever home and will try this octagon cut. 👍🏼You always make tile work look so dam easy, which is a testament to your skill. Thank you again

[@ministerialdepartment885]

I practically spent the bulk of my working day as your student. It is a pleasure having a Tile Coach like you, I have learnt quite a lot about tiling, from you Isaac. Blessings

[@jordonrasmussen3183]

I'm a framer. Every time I get frustrated at my job and take a step away to do something else because I think the grass is greener on the other side I last about a day until miss framing again. Some people are just built for specific jobs. As soon as you accept that and learn to deal with the fact that every job sucks at some point (multiple points) you will be much happier. Nice job on the tile. I'd probably go for the circle, because when you try to do everything totally perfect even your mistakes/ sloppy work (because we are human) are acceptable.

[@yokeyank1]

Q czar pnm8kin

[@tmmyjay]

I feel like this guy has a calling. Not sure it's necessarily tile. Could be something far greater. Seems like a good leader and teacher...

[@a.j.andsweets2199]

Thank you for your valuable practical advise, as always!

[@nickmakris2971]

Never cut an octagon on flange before, but i will this week, and extend the life of the diamond blade.

[@Laking86er]

They'll split finicky tiles a lot easier than circles will. If it's an easy tile to grind than go ahead, but if it's a tile that likes to split, hexagon holes suck.

[@edwardhasiak7961]

@@Laking86erYou are right about that I cut many tiles both ways and it seems to me that the really hard tiles tend to split when doing plunge cuts with a wet saw or using a Makita for toilet flange cuts. Just from the sound of the cut it seemed that the tile was a little soft. But on the other hand he said it was from Italy which from my experience is usually very hard tile.

[@user-lf7en6rf8m]

Hi, i really appreciate these tips, im definitely going to practice this, keep em coming 👍

[@JoseMartinez-bb2qf]

Thanks this the best I've seen in cutting tiles to fit the toilet beautifully ...

[@Jimmy3dLLC]

Thanks for the demo! Yes the circle is important when you’re cutting in for canister lights...

[@ebox008]

Thanks. You take the time to explain, nice and simple. Please remember to wear glasses. Have an excellent day.

[@abrahamhedlin2065]

Issac, FYI the Pearl p4 thin turbo mesh blade that you are using is not made for circular cutting. The manufacturer specifies that one should not put side pressure on this blade, and that it should only be used for straight cuts. Might be worth looking into this, having one of those blades explode when cutting out a flange wouldn't be fun.

[@anthonyseng5222]

It’s a great show for us learn how to learn cut tiles . Thanks

[@optimuss_jedi2394]

I do commercial and residential tile in Austin Texas . I hate having to use the guard and the PPE with the grinder . Some U.T jobs seriously make you cover everything from ears to sleeves,with dust protection for everyone else there too,It’s ridiculous. I started using wet Hole saws with a hand drill and never looked back . The biggest hole saw I have is 5 1/2” . Even on cheap tile it cuts cleanly without breaking. There is also a diamond dry bit (looks like a cylinder) you can buy to make the hole bigger if needed . Highly recommend

I love your channel and videos brother. I learn something handy, new or useful constantly to use for my daily work!!! Much love broski!!!

[@quintonpeter5026]

If you prefer to cut the circle, try sticking a steel flange repair ring in your tile tools to trace. I use a sharpie to trace it so I get that over all 7 1/4”. I’m definitely not a pro like Isaac, just a trick I’ve learned over the years. With that said, I think Isaac sold me on the octagon method.

[@johnvsf]

Thanks for all the Pro tips! 🙏

[@dido1803]

Hey great show. I think octagon shape for sure to save time for toilet purpose. Good to know how to cut circle too if you need to expose the the shape. I'm learning a lot from your videos. Thanks you.

[@rickcavtube]

That's interesting Jack, I never had that experience. Just shows us there is always something new around the corner.

[@GraemeGosse]

I'd be happy with the octagonal cut but appreciate this video because I'm about to reno my bathroom. No toilet but the principal remains the same. I notice you did the first cut on the top side and to the lines, the underside sorts itself out

[@richcawley6009]

Your youtube channel is very helpful. Thanks for doing these I am a DYI guy and without these my work would be subpar and you make my work look like a pro. Thank again. I did round and it worked like a champ. I would agree on the guard on the grinder makes it harder to see your work but I accidently slid my finger on the grinder wheel and as easy as it cuts tile it cuts skin like a hot knife through butter ;-)

[@davidrobins4025]

Thanks for doing this - I am about to lay tile in my basement bathroom on a cement floor. This was really helpful.

[@BruceLinderDPT]

Great video. Thx. Now I just have to find someone to borrow a grinder from. I wonder if I can put a grinding wheel on a drill? I only have one circle cut to make and buying an angle grinder seems an unneeded expense?

[@lvvry1855]

What's the formula for deciding on 2 and 3/4? Great video . Thanks.

[@grumpus3046]

Isaac, great video as always, man. The rest of my comment is for all of you who seem to think the flange belongs on top of the tile...I have watched plumbers lose their minds when it's time for them to come back and install toilets only to realize that some well meaning tile setter pulled his flange because they watched this old house, FFS. What the tile setter has done is create a lot more work for the plumber who has zero interest in drilling holes in tile to install a flange. If the general contractor hasn't caught it before the plumber shows up, I guarantee you the tile setter would be back on the job wasting his own time (money) fixing his screw up because he/she paid attention to some over-paid hack on TV.

[@tilerman]

Nice. When i done my apprenticeship about 400 years (joke!) ago i was taught using 2 hammers to put holes in tiles. A club hammer on the underneath and a small pein hammer to tap away on the face. Took ages but works. That was on ceramics though and doubt it would work on porcelain tiles. Don't do it that way any more of course!

[@johnkenneally4662]

I like the circle look, although you are right that it doesn't make a difference once toilet is placed. Doing a bathroom floor With long tiles now. Removed toilet today.Thanks

[@Derrick_Crenshaw]

Nicely done. Simple, efficient, effective.

[@64maxpower]

I never knew the mesh blade was better for circles. I always struggled some with a smooth diamond blade. Thanks. You know how many people's head you made explode by improvising with a old circular saw blade for a circle. Good job

[@mindshotjon]

I use regular diamond blades and never cut a circle like he did. I just use the grinder and trace out the circle with the blade more perpendicular to the tile. Then cut through in a couple spots, flip the tile, and finish the circle on the backside. Juist as quick as the octagon which i also do depending on mood.

[@raybrown1954]

My 12'x12" x 1/4" porcelain floor tile is breaking during my toilet flange octogon cut. Watched Isaac's video several times and am set up almost exactly as he is, including scrap Kerdi board on flat floor as work platform and same saw blade on Dewalt 4 1/2" grinder. I am going very slowly with a very light hand, and the tile is (3x) breaking in half on the second cut. Last time I had the laptop running and going frame by frame as Isaac demonstrates. What am I doing wrong? The tile is Stonepeak Ceramics, .31 in (1/4"). I am experienced DIY in my home remodel, done very little tile work, but some. Using Rigid basic wet saw on straight cuts. Slow, but steady! Suggestions from the field are most welcome. It is this particular cut I am having trouble with.

[@raybrown1954]

RB back with progress report. Tried the circle cut out rather than the octogon: the 12x12x1/4" porcelain tile broke in half after 5 slow minutes of light handed grinding. This is no doubt a DIY operator issue, but any advice is most appreciated. I am not using the Pearl P4 (did not want to wait several days for delivery). Using Kobalt 4" Turbo Mesh Diamond Tile Saw Blade due to in stock availability at Lowe's. This blade is rated for wet or dry cuts. I am using a 4 1/2" Dewalt angle grinder. I do not think this is a tool issue! Am I asking this 1/4" thick tile to do something it is not designed to do?

[@randyfulton2602]

Will save me time and money...great Video...thanks

[@davem3789]

Like your octagon approach. I’m going to use that method. Thanks

[@emildimitrov9586]

Bravo! Well done, brother!

[@JeffHigday]

I'm not a tile setter, but it looks interesting, and thanks for lessons.. Keep up your calling..

[@enelepurcell2373]

Thank's I learn something new from your video much appreciated God Bless