how the 4x4 vacuum system works on a 98 Dodge Ram 1500
Пікірлер: 52
@leho54164 жыл бұрын
My trucks heater vent was stuck on defrost. Then 4x4 would not engage. Watched your video, found where squirrels chewed through the line. Easy fix. Canceled my appointment with dealer, and saved maybe hundreds . Thank you for you time and talent
@stonewallace6 жыл бұрын
Great video man! It helped me fix my 4x4. My 1995 Ram would go into 4x4, but when I gave it gas, it would make a loud metallic clunk noise. (this turned out to be the collar slipping off the splines inside the axle behind the actuator due to a vacuum leak) - The problem ended up being due to an oil leak soaking my rubber connections, making them soft, that connect my plastic lines to the metal lines that you show in your video at 5:37 and the soft, loose fitting rubber allowed the vacuum leak. After replacing them with short lengths of hose like you did, the 4x4 works great!
@oldgrapeape7 жыл бұрын
GREAT JOB Bud, this was SUPER and NEEDED by me for my 4x4 and it's not now working.
@2001BornAgain3 жыл бұрын
Man you saved me time! I have an issue with my truck not starting and saw the green vent line up against the exhaust before it quit running and it melted. I thought it had an effect on my no start condition and couldn't figure out for the life of me where that green line went. That is, until I saw your video. I went to junk yards hunting this down unsuccessfully, and in less than 5 minutes you eliminated one of my concerns. I'll get it replaced, but thank you for doing this video. It was invaluable to say the least.
@kobaloi26482 жыл бұрын
I've watched this exact video before and didn't realize my problem.... I do now thanks for explaining the vacuum source and everything I replaced the lines under the truck (98 5.9) and was so frustrated that it still wasn't working till I realized my source is cut as well...
@spikedaffy2 жыл бұрын
I don't usually log in to like a video and leave a comment but you have no idea how much help this video did now i can sleep at night knowing that the green hose just sits there lol thanks again and keep up the good work
@BrianOnyshko4 күн бұрын
Yes this video. Was extremely good and very helpful thank you very much
@michaelprimacio53945 жыл бұрын
Thanks man, great and very informative video. Always wondered where the green line hooks up to. Thanks to you , now I know.
@frankiesemailfd5 жыл бұрын
Thank you so much for the video, I looked everywhere trying to figure out what lines went to where
@parkerwork76905 жыл бұрын
Great video, thank you. We have a 2001 Dodge Ram that the 4x4 light stayed illuminated on the dash. switch replaced, not the issue. removed the actuator and fork by removing the 4 bolts. The actuator worked fine. We had constant vacuum from the black line, moving the fork and locking the ring to the left, activating the switch and 4 wheel drive. vacuum lines checked out fine up to the 4 hole rubber grommet. The issue was the red vacuum line not disengaging or creating vacuum to slide the fork and ring back to the right and placing it back into 2 wheel drive and shutting off the 4x4 light on the dash. Vacuum supply line (grey color, and green vent line was good.) Our issue appears to be the same the ball in the switch is stuck creating vacuum to the black but not switching to the red line to release the fork and 4x4 light when working the shifter. The 4 wheel drive did work, just couldn't seem to get the fork to disengage the light or ring for true 2 wheel drive only . I will be removing the switch and clean it up or will be replacing it. Awesome clarification and explanations.
@sharonk17434 жыл бұрын
Thank you so much for putting this on here. Very basic straight to the point information that was much needed. Thanks again. I'll be looking thru your other dodge videos if you have any
@karlsanders96393 жыл бұрын
Thank u very much I understood everything u talked about Every tho Iv never worked on or owned a 4x4 I like the valve of ur talking An just plain an simple With out all the glory hog Good man sir
@dhoop6885 жыл бұрын
Thanks for the answers I needed. Now I can fix my Dodge .
@waynehutchinson14233 жыл бұрын
Thank you very much. It helped me with my 98 dodge ram 4x4.
@sparrowbreed7 жыл бұрын
thank you for making this
@leobonin7805 жыл бұрын
I was having issues with steering, it seemed the truck wanted to go all over the place, I live in montana so 4wd is very important, thought I needed to replace the whole front differential when someone told me it was just the actuator switch, I have been a mechanic for 47 years and have not worked on 4wd so I had no idea where this switch was located, found the switch for $15 but still needed to know where it was to replace it...you pretty much showed me...thanks
@TJSoffRoad Жыл бұрын
Thank for the video! I was worried I disconnected that green line by accident, but couldn't find where it went
@DeanoSavage8 жыл бұрын
Very helpful video. Looks to be the same with the 97 model.
@Blamb.954 жыл бұрын
Best video I have seen about this thanks
@gregorycumming18716 жыл бұрын
Thank you for sharing you knowledge
@john-paulking32894 жыл бұрын
great video informative and helpful thanks.
@edgarjoelmorales10445 ай бұрын
Thanks my friend
@alfredrichard13608 жыл бұрын
I was watching your video on the 1998 4X4 and I heard you say that the green vacuum line was nothing but a vent line? I have been pulling my hair out trying to find a location to connect the green line because I found the rubber elbow that had fallen to the floor but nothing else. Now that I know that it is just a vent all I need to do is find a vent cap and put it together. Thank you for a very good video and good information.
@chriszackery2402 Жыл бұрын
OMG man I broke the white grey line yesterday while changing my plenum gasket and while fixing it found that green line I’ve been online trying to figure out where that green line went for hours 😂
@brandonsatterfield38522 жыл бұрын
Great vid thanks for the help
@BALrider1Steve7 жыл бұрын
Another question I'd like to switch my axle lock from vac to either cable or electronic engage any pointers? Thank you
@johnny04542 жыл бұрын
Great info, thanks 👍
@Gregorian4315 жыл бұрын
Great video Kitt7683. Keep it up. Tony
@whiteboidevin7 жыл бұрын
that first piece you were talking about.. where exactly on the transfer case is that located..
@dennispennock27796 жыл бұрын
where does the third line go from the front diff?
@dannymckee76412 жыл бұрын
Out of 100 videos you were the only one to explain what I needed to know
@carsonadventures31427 жыл бұрын
mine comes out of 4x4 when going up a hill and manifold vacuum is down. I replaced check valve but didn't help..
@Noah-se7mn Жыл бұрын
thank you sir
@daddy14xiv7 жыл бұрын
how many lines are connected to the same white line?,bought a a truck that has like 4 lines but nothing that connects to the white
@edenhomestead53825 жыл бұрын
Does anyone here know the diameter of the rigid plastic vacuum line that runs up underneath the header, and over toward the passenger side? One melted, and I don't think it's available anymore for the 2003 Dodge Ram 2500 5.9L Diesel.
@SHC6666 ай бұрын
anyone got a part number for the actuator, the one on the T case? dodge website is a nightmare trying to find this thing.
@remsoyl9006 жыл бұрын
thanks
@MoBLuBSiAb4LiFe2 жыл бұрын
Is it the same with a 2002 dodge 1500 slt?
@MichaelBorne-rh8co6 жыл бұрын
So at the beginning, the rubber grommet goes onto the actuator. How do I know which 4 holes of the grommet goes onto actuator? And then, how do I know which of the 4 holes of the other side of the grommet(for the soft lines) are for red, black or green or vent, Etc? Does it matter? Like, Those 2 soft lines coming from the 2 metal lines that goes to the little axle motor, owhere on the grommet do those 2 go? Then where does the grommet go onto the actuator, like which way of the 4 holes from grommet to actuator? See what I'm saying, so many ways to put lines, grommet, actuator all back together the wrong way. Unless it doesnt matter which way it all goes back? Appreciate any clarification you can give. Btw, EX VID!
@Benjammin434 жыл бұрын
my vacuum lines just go back into the harness they came from and don’t go down to the metal lines. and my front axle doesn’t have a spot for the vacuum hoses either. I am confuse. 1999 ram 1500 5.2
@andresrenteriaceniceros3864 ай бұрын
Thanks
@twatson62525 жыл бұрын
I am looking for a new rubber grommet can't find one on ebay hate to go to dealer.
@butterbean41954 жыл бұрын
good information. would a vacuum leak cause the throttle body to sound like its sucking air or starving for air? my truck runs fine and will idle fine and just start sucking air big time. ive checked all around the throttle body for leaks but see nothing. any ideas? and also this problem affects the cruse control to
@glenni88353 жыл бұрын
Did you ever get this solved? I am having the same issue now.
@kadams68684 жыл бұрын
What size wrench do you need to get the old switch out?
@jamesridenhour15204 жыл бұрын
7/8
@chexmygold7 жыл бұрын
do you know if the 2500 is the same as the 1500 with respect to this problem ?
@mtr58477 жыл бұрын
chexmygold diesel or gas
@chexmygold7 жыл бұрын
360 gas
@mtr58477 жыл бұрын
chexmygold Yes its the same. I would check the metal tubes that the red and black lines go to it was my problem but if you remove the part where the vacuum runs to by the axle heat the bolts up it will save you a headache