I appreciate the video, my old man has been in the hospital and i couldn't have fixed my truck without this video.
@km63442 жыл бұрын
Ya know,,, all I can think when I see thumbs down on great explicit videos like this is,, that there are people who are so miserable in their own lives that they just have nothing better to do then just go video to video thumbing them down without even watching them! This was the best how it's done video start to finish I seen so far! Thank you so much! I seen how the plug lines went on correctly ( since mine were played with and coulda went either way) before you taken it apart all the way to where exactly the vent gets attached behind the coil spriing! Great video! Helped me immensely! Thank you for posting this!
@york575 жыл бұрын
Probably the best video I had ever seen with great detail. Thanks
@davekana83883 жыл бұрын
Beautiful work, most helpful. I didn’t know how the system works until I checked out this excellent video, thanks, Dave!
@PTBob721 Жыл бұрын
Thanks for the effort of producing this concise video. I'm about to make the same repair on my Dodge Ram and it's nice to see all the components up-close and clearly shown before I climb under my just recently Fluid Film coated truck. Much appreciated!
@jerryharrington11525 жыл бұрын
Great video, I like the way you explain things. Not to fast and very clear. Thanks
@williamgonzalez27025 жыл бұрын
Excellent video. Straight to the point. Excellent job.
@FreakinA552 жыл бұрын
I know this vid is 3yrs old but a question for anyone willin to answer, the red and black vacuum lines on the actuator, do those both have vacuum pressure while the truck is runnin?
@moonreft5 жыл бұрын
Thank you for your video, I'll check vacuum once the snow melts
@eneeland2 жыл бұрын
Outstanding how to video. I am impressed with your thoroughness and sequence of action. Well done and thank you.
@rickhartman3960 Жыл бұрын
Thank you for a great video. Very helpful and informative. 12:10 12:10 12:10 12:10 12:10
@rpkyle3124 жыл бұрын
Fantastic video, it was super easy to understand and right to the point. This was extremely helpful and exactly what i needed to see to get me running again. Thanks a million!!!!
@butterbean41953 жыл бұрын
doing this tomorrow thanks good stuff the only thing i would add is if you have a compressor blow through the lines to make sure no leaks or stopped up like mine was.
@robertmanley75565 жыл бұрын
Thank you so much for your video! It was very informative , very thorough, help me out tremendously mine was quite a bit more rusted then Yours some WD-40 and some time and patience I got it apart got to put back together and now my 4 wheel drive is working again! Thank you very much!
@properboy9979 Жыл бұрын
Thank you Jay... very helpful and clear instructions
@timobrien9459 Жыл бұрын
Thanks Jay, nice to not have to reinvent the wheel!!!
@tracyphillips3325 Жыл бұрын
Very detailed video. Excellent job
@themechanicman38652 жыл бұрын
That I haven't seen in many post and forums this is a very good informative video very detailed so great job on that but also zit pops on control the light is coming on but it's not actually going into four-wheel this is going to be my next thing is doing a pressure test to see that if it is holding a vacuum if it isn't then we know that that's a bad diaphragm and I'm going to replace it thank you
@cesaregaglio47252 жыл бұрын
Very detailed video excellent job thank you very much for posting God bless
@bobbobbobbob14493 жыл бұрын
Just awesome no bs just teaching. Keep it up
@edwincrouse564712 күн бұрын
Thank you buckets !
@rogeliohernandez55333 ай бұрын
Hi, old video but this helped a lot! How much oil should I put a into the axle at the end?
@secretsquirrel63082 жыл бұрын
This is instructional video is very well done. What is the source for parts, particularly the yoke shoes?
@drizski Жыл бұрын
Thank you very much - very helpful.
@kenhulse51915 жыл бұрын
excellent and clear .the best one I have seen on this process
@indoplasmic32035 жыл бұрын
Very good video! Very thorough! Thank you for making this video!
@robertratajczyk72484 ай бұрын
Seen a hose hanging from bottom of my truck; turns out it was just the actuator vent hose...thanks
@Gregorian4315 жыл бұрын
Thanks Jay. Great video. Tony
@mannyleon_landscaping89272 жыл бұрын
Thank you for your video and your teaching, it helps me a lot to fix my truck, thank you very much for sharing your knowledge and experience, a new subscriber to your channel👏👌
@tomb3742 жыл бұрын
great video.. very well done. I was told that if the front driveshaft/axle wasn't engaged that the truck would roll if it was in park. if one front axle is split by this collar how could that be true? it also seems that the opposite side axle would be working the differential to death in two wheel drive. What am I missing here? Is the transfer case constantly in 4wd to keep this from happening?
@brianb5779 Жыл бұрын
Appreciate the info, thank you
@davem9939 Жыл бұрын
i need the little black and red hoses - do most parts stores have them ?
@dmorales86812 жыл бұрын
Thanks. Excellent video 👍👍👍👍👍
@bobgarcia26952 жыл бұрын
Excellent!
@terryscull4405 жыл бұрын
If the 4x4 light comes on, does this mean the actuator is working correctly?
@WilliamFrawley5 жыл бұрын
yes, the light will not come on until the 4WD is fully engaged
@erichctransportation42455 жыл бұрын
Great video, help me 100% point to point really good video, thanks
@shanesmaineshop2 жыл бұрын
great video
@juanm.castillo11354 жыл бұрын
Well done full of info thanks you would make a super instructor
@dkjohnson573 жыл бұрын
Thank you for this video,my truck is stuck in 4 wheel drive,can the actuator cause this problem ? The truck went into 4 wheel drive but it won't shift back out .
@WilliamFrawley3 жыл бұрын
If the vacuum diaphragm is leaking then it may not be able to shift out of 4WD. You can try jacking the front end off the ground. Remove the actuator sensor and there is a rod in the actuator that pushes against the sensor. Push on the rod to slide it out of 4WD. You might have to "rock" the passenger tire back and forth while pushing the rod. The engine should be OFF. Be sure the vehicle is safely supported.
@bobbygarza69054 жыл бұрын
Excellent video!!! Very helpful.... Thank you...
@philipboots983 жыл бұрын
Thank you! This video was very helpful!
@josemanuelreyesbarrios97293 жыл бұрын
Aight guys .. need some help ... Where does the last line goes attached to after the clip ... Cuz mine is broken and the hose is hanging out till the connector
@tylawson245 жыл бұрын
Awesome video man!! Very detailed!!
@marcsmith38815 жыл бұрын
Excellent Video!
@millermatic1404 жыл бұрын
My light stays on in 2wheel drive, in 4x4 it turns off. Does this mean my 4x4 is stuck and engaged? One time the light went off on 2H and also stayed off on 4H. I tried changing the sensor.
@jamesstultz79205 жыл бұрын
What about replacing the fluid inside the front differential?
@hunterboehm71355 жыл бұрын
remove cover, clean, RTV silicone, reinstall, remove fill plug, fill until it leaks out, reinstall fill plug, done.
@tullyman824 жыл бұрын
Just suck it out add new
@waynehutchinson14234 жыл бұрын
Excellent detail.Thanks
@stevenr60334 жыл бұрын
Thanks!!! I’ll be doing this next week
@rafaeldelgadillo16135 жыл бұрын
Does it matter if I take that piece out with 4wd engaged?
@WilliamFrawley5 жыл бұрын
No, just make sure when you put it together that the "yoke" goes over the collar. (once you have it apart you should be able to slide the collar in and out of 4 wheel drive by hand)
@jaykay85702 жыл бұрын
Just a fyi for everybody-- test your new actuator before you install it. I got two bad Dormans in a row.
@RamonLFrancisco4 жыл бұрын
Great video. My lever on my 99 Dodge Ram1500 is difficult to move from 2H to 4H, N and 4L but after toggling the lever a bit, it does move to 4H and I see the light on the instrument panel. I got this truck a month ago and truck works great overall but I want to figure out how to make it easier to move the lever. I am not sure if related to the vacuum actuator or shifter assembly needs some WD40 so shifter moves easier like yours in the video? Any ideas? Thanks.
@ethandart83844 жыл бұрын
That would be your linkage to the transfercase
@nevadawashington34304 ай бұрын
What if the light come on when in two wheel drive but goes off in four wheel drive
@WilliamFrawley4 ай бұрын
Are the vacuum lines possibly switched around? Is it actually in 4WD when you shift out of 4WD?
@normdeclercq40523 жыл бұрын
Nicely done
@abepolster8124Ай бұрын
Where do I add the oil for this? And also what type of oil is used?
@IG1070528 күн бұрын
Through the front inspection plan. Go to the parts store and tell them what you have they will bring it up or better yet Google it
@tonycruz1173 жыл бұрын
Great video ,, thanks
@jeffphillips72904 ай бұрын
Where did you get the parts ? Nobody seems to have them anymore. Dodge discontinued them in 23 july
@WilliamFrawley4 ай бұрын
I ordered the parts from RockAuto
@IG1070528 күн бұрын
EBAY AMAZON ROCKAUTO SUMMITRACING
@jonathanrayfencing18244 жыл бұрын
Like everyone else says awesome video
@andrewsarkis26632 жыл бұрын
Currently doing this on my first gen. I can not for the life of me get the new diaphragm installed without destroying the part or myself. The original diaphragm had to be hammered out. Anyone have any tips?
@kylebenham5832 жыл бұрын
Awesome Video! Curious to where you found the punisher emblem?
@WilliamFrawley2 жыл бұрын
it's just something I designed and 3D Printed
@ke1vin2 жыл бұрын
Anyone here after watching that 1A auto video?
@ashtonowens42494 жыл бұрын
I’ve got a 96 ram 1500 4x4 but I’m always scared of putting it into 4 because of grinding noises. Am I not supposed to be in neutral or is something wrong?
@ethandart83844 жыл бұрын
Sounds like you need a new transfercase
@ashtonowens42494 жыл бұрын
Ethan Dart I actually just was able to get into 4 wd it wanted to be in drive
@signal4x774 жыл бұрын
What were the symptoms of having to replace this actuator?
@ethandart83844 жыл бұрын
Your 4x4 not working
@JohnDoe-ud2cc Жыл бұрын
Where did you get the hood emblem???
@WilliamFrawley Жыл бұрын
I designed it and then 3D Printed it
@JohnDoe-ud2cc Жыл бұрын
@@WilliamFrawley want to make another???
@turbonegro65535 жыл бұрын
please tell me where you got that punisher emblem on the grill
@WilliamFrawley5 жыл бұрын
I made it on my 3D Printer
@MasterchiefB2085 жыл бұрын
Unrelated to the video itself, how or where did you get that punisher logo on the grill?
@WilliamFrawley5 жыл бұрын
I designed it and then 3D Printed it
@canadaplace2be1763 жыл бұрын
Mickey mouse. 4x,4. I can't believe. Dodge does really suck. Hubs nice. Vacuum. In 40 below?