A $100 Wireless In Ear Monitor System & Other DIY IEM Setups

In part 3 of 4 in my IEM video series, we go over a way to get a $100 wireless in ear monitor system, and other DIY IEM monitor setups you can use for your performances. Check out this video for a great IEM hack.
👇👇👇 FOLLOW ME ON INSTAGRAM👇👇👇
✨ / scottuhlmusic
🤘🤘🤘 BOOK A CONSULTATION 🤘🤘🤘
🌐 www.scottuhlmusic.com/consulting
🎸🎸🎸 MY ORIGINAL MUSIC/PROJECT "SPIRAL CELL" 🎸🎸🎸
🎵 / spiralcell
🔥🔥🔥 DEALS & DISCOUNTS 🔥🔥🔥
💥 Best Deals on Sweetwater:
👉 sweetwater.sjv.io/XYZyyy
💥 5% OFF Phenyx Pro products (use promo SCOTTUHLMUSIC):
👉 phenyxpro.com/?ref=zo7epbiric 👈
🤗🤗🤗 SUPPORT THE CHANNEL: 🤗🤗🤗
☕ Buy Me A Coffee: www.buymeacoffee.com/scottuhl...
💸 Send a Tip: www.scottuhlmusic.com/tips
0:00 - Intro
0:52 - My $100 Rig
1:43 - Why Would You Get This
2:20 - Gear Needed
2:35 - Receiver Options
4:39 - Wireless Transmitter Options
6:30 - Earbud Options
7:23 - How to Setup
8:42 - How I Use This Setup
11:11 - Accessories
11:49 - Final Advice
🔥 MY $100 (actually $125) WIRELESS IEM RIG 🔥
●▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬●
◆ BEHRINGER - POWERPLAY P2 ◆
amzn.to/2x8N85u
◆ **DONNER - EM1 - PORTABLE HEADPHONE AMP ◆
(Behringer P2 is often backordered. I like this one as well)
amzn.to/2Qkwh9q
◆ CCA - CA4 DUAL DRIVER IN EAR EARPHONES ◆
amzn.to/2x6XHWF
◆ AMMOON - 5.8ghz WIRELESS GUITAR SYSTEM ◆
amzn.to/34nzOGi
🔥 INEXPENSIVE RECEIVER OPTIONS 🔥
●▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬●
◆ BEHRINGER - POWERPLAY P2 ◆
amzn.to/2x8N85u
◆ DONNER - EM1 - PORTABLE HEADPHONE AMP ◆
(Behringer P2 is often backordered. I like this one as well)
amzn.to/2Qkwh9q
◆ DONNER - EM2 - PORTABLE STEREO HEADPHONE AMP ◆
(Same as above but 2 inputs with stereo/mono switch)
amzn.to/3ne3ak3
◆ BEHRINGER - POWERPLAY P1 ◆
amzn.to/30l2b7A
◆ BEHRINGER - MICROMIX MX400 ◆
amzn.to/34rhpbN
◆ ART - MY MONITOR II ◆
amzn.to/3fXZ9eo
◆ ROLLS - PM50 ◆
amzn.to/3e8lje0
🔥 WIRELESS TRANSMITTER OPTIONS 🔥
●▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬●
◆ AMMOON - 5.8ghz WIRELESS GUITAR SYSTEM ◆
amzn.to/34nzOGi
◆ AMMOON - 5.8ghz WIRELESS GUITAR SYSTEM ◆
(Same company, just a different look)
amzn.to/3bmOFnj
◆ SWIFF AUDIO WS-50 ◆
amzn.to/3u2dH4G
◆ LEKATO - UHF WIRELESS SYSTEM ◆
amzn.to/3s4wLgW
◆ LEKATO - 5.8GHZ WIRELESS ◆
amzn.to/2W9HFE9
◆ GETARIA - 5.8GHZ WIRELESS SYSTEM ◆
amzn.to/34NwxQS
◆ AMMOON - 2.4ghz WIRELESS GUITAR SYSTEM (only $39) ◆
amzn.to/2VfAz0a
◆ BOSS - WL20 ◆
amzn.to/34oBIGM
◆ NUX - B3 ◆
Wireless XLR System
amzn.to/3kCJynZ
🔥 EARBUDS 🔥
●▬▬▬▬▬▬▬▬▬▬●
◆ CCA - CA4 DUAL DRIVER IN EAR EARPHONES (only $20 😱) ◆
amzn.to/2x6XHWF
◆ CCA - C12 IN EAR EARPHONES (6 drivers) ◆
amzn.to/30jRmTm
◆ EASY KZ - DUAL DRIVER EARBUDS ◆
amzn.to/30O03pf
🔥 ACCESSORIES 🔥
●▬▬▬▬▬▬▬▬▬▬▬▬▬●
◆ FEMALE XLR TO FEMALE 1/4" ADAPTERS ◆
amzn.to/30QCCvF
◆ ROLLS - 3 CHANNEL MIXER/COMBINER ◆
amzn.to/2Cm76fz
◆ HOSA - XLR ATTENUATOR ◆
amzn.to/2XqReAA
🔥 MY NORMAL IEM RECOMMENDED SYSTEMS 🔥
●▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬●
◆ SENNHEISER - EW 300 IEM G4 ◆
amzn.to/34pT7ih
◆ SHURE - PSM300 ◆
In-Ear Monitor System
amzn.to/3k7ngKD
🔥 DIGITAL MIXERS I USE FOR RUNNING INEARS FOR MY BANDS 🔥
●▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬●
◆ BEHRINGER - X32 RACK ◆
3U Rack Mixer
amzn.to/2yJpahl
◆ BEHRINGER - XAir XR 18 ◆
Tablet-Controlled Digital Mixer
amzn.to/30olJZ3
All links are Amazon Affiliate links
🎥 MY IEM VIDEO SERIES 🎥
●▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬●
Video 1 - "Beginners Guide to IEMs"
• Beginners Guide to In ...
Video 2 - "Running Your Own IEM's"
• How to Run Your Own In...
Video 3 - "$100 DIY Wireless IEM Rig (and other cheaper IEM rigs)"
• A $100 Wireless In Ear...
Video 4 - "My Favorite Portable & Compact IEM System (IEM Hack)"
• Portable and Compact I...
🎥 ADDITIONAL VIDEOS AND INFORMATION 🎥
●▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬●
More about the 5.8ghz wireless:
• Cheap Guitar Wireless ...
How To Always Hear Yourself On Stage & Control Your Own Mix:
• How To Always Hear You...
💥 HIRE ME TO HELP YOU 💥
●▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬●
www.scottuhlmusic.com/consulting

[@ScottUhlMusic]

Thank you guys for checking out the video, and hope you found it useful! If you are looking to spend a little more money, I made another video about a very simple and extremely portable IEM system that I use most of the time I travel for gigs or whenever I don't want to take my Sennheisers out of the rack. Check out the video here: kzbin.info/www/bejne/Zoi3apl-prutkMk

[@christianpucciarelli]

Hello Scott,is the ammoon t/r system mono? Is it a problem to run mono iem system ?

[@ScottUhlMusic]

@@christianpucciarelli It will be a mono system using this method

[@christianpucciarelli]

@@ScottUhlMusic I guess it works good anyway ?

[@ScottUhlMusic]

@@christianpucciarelli It works great! But you have to realize this is a wireless IEM "hack"... this isn't a normal way to use IEM's. If you are truly interested in IEM's and you have to get stereo, and you are super picky about your tone, this isn't the video for you. Gotta shell out the money if you want that! This is a trick to save money.

[@christianpucciarelli]

@@ScottUhlMusicim just starting looking at iem and wireless ,that’s why I’m here ;) and I have found very good info in your videos

[@JackDeiten555]

no one else makes this type of videos and its legit what most of us are looking for. ty.

[@HoldenLeDinh]

Exactly!!!

[@Littopastor]

You're that kind of guy that can make anything fit and work together seamlessly. If you were my neighbour, we'd share the bread bans I make. Top man.

[@ScottUhlMusic]

Hahaha thanks man

[@izzy4el]

Hot damn, what a great video Scott! Don't know how I'd missed it. You're putting out a lot of great content and so helpful/useful. Thank you!

[@TheBluesine]

Once again great vids Scott, very helpful mate!! cheers

[@ScottUhlMusic]

Thank you 😊

[@ignasi79]

Thanks for the video man! I was about to build something very similar and I was a bit unsure about how would the wireless receiver and the P2 behave together so your video just confirmed me it works. Great tips and gear recommendations. Thank you for sharing!

[@ScottUhlMusic]

Glad to help 🤘

[@phil76414]

Great video. Love the diy aspect. Thinking of using this in rehearsal to take the mixing desk aux out to my shure in ears rig instead of the ridiculously long cable I’m currently using!

[@ScottUhlMusic]

That’s definitely a great way to use it!

[@gritsguitar]

Excellent! Just what I need. Thank you much.

[@ScottUhlMusic]

🤘🤘

[@phoenixnj13]

Scott thanks for sharing this idea this worked perfect

[@ScottUhlMusic]

Awesome! Glad to hear it 👍

[@catrambull]

Amazing!

[@shanegeorgethomas3733]

Respect, man. This is exactly what beginner live-performers like me, need. Cheers!

[@ScottUhlMusic]

🤘🤘

[@shanegeorgethomas3733]

@@ScottUhlMusic Also, can you please mention if in-ears with mics are okay? Found the CCA 12 at a very cheap rate with mics

[@ScottUhlMusic]

@@shanegeorgethomas3733 Get the ones WITHOUT Mic for in ear monitors. I reviewed the CCA's here: kzbin.info/www/bejne/roe4l2qdZ859gJY

[@xbrandon]

yo thank you for doing this!

[@ScottUhlMusic]

🤘🤘

[@girmadaniel1324]

Thank you sir ....very very good advice

[@ScottUhlMusic]

Thanks!

[@kadirbadavid4418]

Excelent my friend congratulations your video very good!!! Saludos desde Colombia.

[@ghazwanaltimimi1794]

Thx , very informative

[@ScottUhlMusic]

🤘🤘

[@RadityoPramAdi]

thnks a lot!! this is really helping..

[@ScottUhlMusic]

🤘🤘

[@tonybirol6632]

Man your brain is just awesome lmao thanks for this!

[@charlschuck6]

You got so much option in one video nice heheh thanks

[@ScottUhlMusic]

Definitely wanted to give as many cheap options as possible 😊

[@omarfigueroa3681]

U know what’s crazy I actually do this as well 😭😭😭 I never seen dis video but I had da same idea😭😭 this is awesome doe

[@ScottUhlMusic]

It’s a nice little hack 🤘

[@whodaman5]

Build this exact rigs for pub gigs where we run our own PA. So far so good.

[@ScottUhlMusic]

Nice!

[@RexyFan]

Great content and hacks. New sub.

[@ScottUhlMusic]

Thank you 🙏

[@cletusrobinson]

I have a QSC TouchMix 16, which enables everyone to tailor their mix. Your tip will help me a great deal to get started. Thanxabunch!

[@ScottUhlMusic]

Glad to help! Also just keep in mind that the more of these cheap wireless you have next to each other, the more likely they are to get dropouts. Using 1, or 2, or 3 are usually fine, just don’t put them right next to each other. That’s part of the reason IEMs and wireless have different price points... the higher the price, usually the more units you can use at once

[@normanfloyd]

Does it works? I have the same mixer, , I did with the aux and cable but doesn’t have enough volume, cuz is “line level”, I’m wonder if it works with this, I’m doing it wired

[@jeanenviedapprendre]

This is EXACTLY what I need! My church has some P16 monitor mixers, but I've resisted because I won't have my ears tethered to the P16.

[@ScottUhlMusic]

Glad to help out :)

[@palafunk]

awesome !**

[@ScottUhlMusic]

Thanks!

[@sparkyguitar0058]

The comment about cords around your feet hit home. Im even picky enough to clean around my spot on the worship stage I play on. Cords, Mic stands, monitors. Got to move it all every week. Don't know how it's always in the way.

[@ScottUhlMusic]

Yeah, it’s such a pet peeve of mine. I just like being able to move around without being tethered, which is why I’m just always wireless

[@bovinlee1641]

this is lifehack!!!!! amazing

[@phoenixnj13]

I had to change it up a bit from yours because I had the PM1 but I just purchased the Stereo female to xlr male adapter instead and was able to obtain the same results :)

[@ScottUhlMusic]

Awesome! Glad it worked 🤘

[@yenti2005]

Good video! A little corny with the movie video clips, but overall a good video demonstration.

[@louiscarrillo5873]

genuis !!!

[@ScottUhlMusic]

🤘🤘

[@tomasuribe2698]

Great f video. I am new to monitoring and just got the Behringer P1, and it's a bit easier since I just want to monitor my voice straight from the mixer. Thanks a bunch for the explanation man, I was trying to look for a video that was detailed enough to understand how to do it, so far this is the best video I've seen. Can I then buy the nux b3 and be entirely wireless? Thanks a bunch and greetings from Colombia, South America

[@ScottUhlMusic]

Yup, can be entirely wireless if you use the nux b3 on your mic and then this setup for your inears 🤘

[@Eduard_Kolesnikov]

Nice, that's what I did as well. Just another old amplifier (Audio Technica)

[@ianmartin2924]

KZ ZS10's are amazing!

[@tuffblue]

Love your work Scott Should I use a different band for in ears to the guitar wireless.? For example 2.4ghz for IEM and 5.8ghz or UHF for guitar.

[@ScottUhlMusic]

If you only have 2 wireless going on stage, you should be ok either way... but it definitely wouldn’t hurt to do it that way if you can 👍

[@danielgreenberg4751]

This is neat! Is the sound in one ear or both ears when you do this?

[@ScottUhlMusic]

Both. If it’s in one, set the switch to mono 👍

[@rafaelikenaga]

Thank you this is really cool! Any option to make this stereo? I wouldn’t mind putting extra bucks init but I wanted something compact

[@ScottUhlMusic]

I don’t know anything that would do that that is in stereo and this compact. But if I find one I’ll definitely do a video on it 👍

[@florinlungu4456]

Hi Scott, great videos and very useful info here on your channel.. Can you recommend an updated option instead of ammoon - 5.8ghz to use it in yhe same combination as a cheap IEM sistem with the Behringer P2? What about the SWIFF AUDIO WS-50 or Lekato ws-70? Thanks in advance.

[@ScottUhlMusic]

Yes, either the Swiff Audio or the Lekato ones will work great too. I have a lot of them listed in the description... all of them will work great with this setup. Cheers!

[@yairidy90]

I've tried this and it works great in my garage. Will try at a gig next week. I went with the lekato wireless that runs on UHF frequency so it wouldn't conflict with my NU-X B5RC that runs on 2.4ghz. only difference I can tell going wireless is it almost seems like there is a noise gate or something. I don't hear the first click of the click track but I do when hardwired with a cable. Weird. Small price to pay for being able to move around and not trip on any cords.

[@restymalinao2023]

Awesome content! I also have the amoon 5.8Ghz version, it's super awesome. I just have one question, I noticed that the 1/4" plug is mono, if you're gonna use it for IEM, you just hear a mono mix sound?

[@ScottUhlMusic]

Not if you are plugging into a MONO IEM/headphone amp. I did a video about how to do that here: kzbin.info/www/bejne/jaHZnImog7anrqM

[@crocholiday]

Dude... I HATE cable tangling. For the band we have sweet Sennheiser in ear system but at home... I'm tethered by cables... Tried blue tooth but even fast transmitters have a lag. Recently nabbed this wireless system on your recommendation and it's great. Maybe a shade bright but definitely workable until I'm willing to pony up for Sure. My first thought was to get another pair and reverse it for the home cans. Beat me to it haha. I would have just gone to a cable adapter but think you're spot on with the in ear amp for volume control. Great videos. I appreciate the work you've done to try these all out and share your experience. Thank ya sir!

[@ScottUhlMusic]

Dude, I still use my wireless at home! I absolute hate being tangled in cables. Even when I do solo acoustic (looping) sets, I have a wireless mic, a wireless guitar, and wireless in ears just so I'm not tethered haha. It's kind of an obsession! Glad you found the videos useful

[@crocholiday]

@@ScottUhlMusic Any suggestions beyond the P2? They're pretty much out everywhere. Next jump up I see is $80 or more. Side note... I thought I'd get around the need for the monitor amp with a series of adapters. It worked but sound was like 30% of what my cable was. I asked our sound tech what he thought it might be. "Um, that little thing can't push enough power to run cans." Power... something taken for granted in cables that I didn't eve consider lol.

[@ScottUhlMusic]

@@crocholiday Yeah I need to look into other options. My drummer broke his P2, and had to order a new one and it's been on backorder for over a month. It's just now arriving in like 2 weeks. I'll have to look into other options

[@BloodlineMetalfromGermany]

Thank you so much for your videos! ✌🏼🤘 How would you rate the In Ear sound in general and also with some high gain guitar tones?

[@ScottUhlMusic]

For this DIY inear system, it sounds fine to me, but some people are more picky for their tone. However, in general for high gain guitar tones and for bass I definitely would recommend getting custom molded inears and at least 3 drivers. With the universal fit ones it kind of sounds a little tinny. You get the general idea of what your tone is, and you can hear if you are making a mistake and stuff like that, but the quality improves drastically with custom molds in my opinion. But after switching to IEM, I have a hard time doing the few songs I’ve done without them. I love them

[@BloodlineMetalfromGermany]

@@ScottUhlMusic Thanks! How much sound-difference is there when you compare it to your Sennheiser wireless ... ?

[@ScottUhlMusic]

I would say this diy set up gives you about 80% of the quality of the sennheiser unit. You definitely get more noise/static with this one. It’s definitely still useable imo, but you get what you paid for, and the sennheiser is definitely better of course. I still use this setup for my acoustic shows though

[@shanedutoit9101]

Bought the P2 on your recommendation and it works nicely, so thanks very much for that. Was looking for an affordable solution to very annoyiong cable problems. I already had a 2.4Ghz Getaria for my bass so though I would try it with that before buying another for the IEM's. Has a little bit of static noise or interference so I will be purchasing a more expensive 5Ghz set to hopefully sort that problem out. Sidenote, I ony have a couple of phones/tablets in my studio using wifi, other than that there are no wireless signals in the room at the same time.

[@ScottUhlMusic]

5.8 should be better, but… just remember this stuff is cheap for a reason, and this is a DIY hack for and IEM system. It works for sure, and I’ve giggled with it… but if you want a really good one, you’ll need to spend the money. This is usually the one I recommend to start with for beginners since it’s not very expensive at all: kzbin.info/www/bejne/mnuvkK1_Z8mliLM

[@shanedutoit9101]

@Scott Uhl That looks like the system I'll check out for the future. Thanks dude. I'll try the 5Ghz one first. Thanks a ton for the advice man🤘

[@damiendemougeot2065]

Hello, Finally the sound is mono or stereo ? Thanks a lot ! Damien

[@ScottUhlMusic]

This will be mono

[@guenterjaklitsch6561]

Hi Scott - thanks for this very informative video I have a Line 6 pod go. Can i use a wireless guitar system to play wireless and use another wireless one as a IEM like you showed in your video ? Or do I need only one ? How do I connet those pieces ? - Thanks a lot!

[@ScottUhlMusic]

Yup you can do that for sure. One wireless from guitar to pod input, and one wireless from pod output to P2 or any other headphone amp for a DIY setup like this 👍

[@ckowalski1029]

Thanks for this. Would this receiver work with the Behringer X-air x16?

[@ScottUhlMusic]

Yes it would 👍 you would just need an xlr adapter

[@smartfamilymedia]

Thanks for the great video. Links to Ammoon 5.8G etc no longer work. Which units should I look at?

[@ScottUhlMusic]

Thanks! I would check out the lekato one that is in the description. Or also this one: kzbin.info/www/bejne/eoTUlZdjYpVpnrM

[@margarex4113]

Great video. Would this set up be suitable for singers to hear themselves? Thank you!

[@ScottUhlMusic]

Yup, definitely 👍

[@scottgoesba]

I went to try this setup and the P2 of course is backordered so I thought I'd try the EM1. I am wondering if because you can't change mono stereo on the EM1 I am not getting a signal at all. I saw your other video for that Nux B7PSM and might just go that route, but still wanna know what I did wrong here haha! Your videos have been very eye opening and helpful!

[@ScottUhlMusic]

You should get signal still even without the mono/stereo switch on the EM1, so something else is likely wrong. And you can get a TRS male to TS female adapter for very cheap

[@Atamone]

Great video. Im looking for a budget wireless monitoring system to send click track to headphones... Im looking at the BOYA XM6 (Rode Wireless GoII alternative) wireless lavalier system to use as a wireless pack to send my headphones mix to the receiver. But seeing some of your other reviews, maybe I should stay away from 2.4ghz? Hope you can have a look, as its seems like an easy stereo option with the line-in/out option. 5ms claimed latency is also is to consider. Im also just a 1 man band type with the occasional guest musician, so moving far distances is not a priority, Not sure if distance helps the 2.4ghz stability, but im typically never further than 10ft from my setup. Thank you, Just subbed, great content! Cheers

[@ScottUhlMusic]

Thanks! I just looked at it, and yeah with it being on 2.4, that’s the worst part. 2.4 does still work, I’ve just had a lot of bad luck with it. So I would suggest looking into this one: kzbin.info/www/bejne/n6qqhIWvibyVnqc It’s actually cheaper 👍 And 5ms of latency is definitely nothing to worry about if you do decide to get the BOYA instead. You won’t hear that. But the one in the video link I sent is cheaper than the BOYA and works really well. My singer uses it as his main wireless IEM system

[@Atamone]

@@ScottUhlMusic thanks so much for the reply! your videos have been very helpful! i will consider the Phenyx Pro model. thank you. (: (:

[@MattiHaflert]

Thank for the video! When practicing with the band I can image i'd just insert the wireless receiver in the P.A. But when we play live the distance between stage and FOH might be a few meters. How will this affect the signal? Of should I be able to connect the transmitter somewhere onstage? Thanks!

[@ScottUhlMusic]

Range always depends on the conditions of the venue. And with cheaper wireless gear you often do get less range. I believe these will be good for 50-100ft in good conditions. So it will depend on the show and the wireless environment at the show. Remember, this is an IEM “hack” to save money. It won’t work in every single scenario. If you need a full on IEM system, you can still get some for pretty cheap now 👍

[@DespairQuietlyPlease]

Hi Scott Love your channel. Thanks for taking the time. I'm setting up a new home studio. Like you I detest cables so I'd like to go wireless monitoring/recording. I have a decent budget up £1000 ($1500) Input 1 Guitar to amp (wireless) Input 2 Guitar Amp to mixer/interface (wireless) Input 3 Bass to amp/pedal board (wireless) Input 4 Bass amp to mixer/interface (wireless) Input 5 Mic to interface/mixer (wired) Output Mixer/interface to wireless IEM (wireless) So I make that 5 lots of paired units with as close to zero latency as possible. Do you think the setup you mention in this video with the Behringer pack would work or could you recommend another? The idea is to have everything connected permanently to make workflow as straightforward as possible...just pick up, play and monitor with zero sound being emitted beyond the in ears. Thanks again

[@ScottUhlMusic]

I think that should be fine. If you start compounding wireless that’s where you can start getting latency, especially with cheaper ones. I’m assuming bass and guitar amps are separate. Buffer size might be an issue, but I think it would work 👍

[@Yakumo00o]

Hi, thanks for presenting this solution. I'm searching a wireless setup for silently practicing with my electric violin at home, running it through my amp. As non-DIY Setup I thought of a Line6 G10 for violin>amp & Xvive U4 for amp>in-ear, which would end up at ~400$. Line6 G10 only because it's highly recommended in violin forums, since I heard that not all transmitters work that great with piezo pickups, since they got a high impedance. If I instead try this budget solution, could I use 2x ammoon transmitter for violin>amp & amp>in-ear or are there interferences to be expected? Would you recommend these transmitters for piezo pickups?

[@ScottUhlMusic]

I do not believe the G10 works with piezo pickups, but I could be wrong. You could go with 2 Ammoon ones. Use the black one for the violin and the red-ish one for the IEM system 👍

[@VANQU1SHR]

Great video, thank you. Any updates to your recommendations now that it’s been a few years since you recorded this???

[@ScottUhlMusic]

Yeah they make portable ones very similar to this design for like $100 anyways haha. Like this one: kzbin.info/www/bejne/i6DVfZ-Vq92Md5Y

[@VANQU1SHR]

Awesome. Missed that one so thanks. Having watched that one, I’m going with this system to get the 5ghz. Awesome vids bro. Thanks.

[@modusartsgroup]

I am using a BOSS WL-50 transmitter + receiver set FROM my guitar INTO my Digitech RP360 effects processor/amp simulator. And then a BOSS WL-20L transmitter + receiver set FROM my Digitech RP360 and finally INTO my Behringer Powerplay P2. The BOSS WL-50 and WL-20L work seamlessly and without interfering with each other. You just have to remember to "pair" each set's transmitter to the proper receiver before each session. Coming OUT of the Digitech RP360's stereo 1/8" output jack via a high quality 10' long, 1/8" to 1/8" patch cable, I then use a high quality 1/8" female to 1/4" male adapter going into a high quality 1/4" female to 1/4" female line connector, with the WL-20L transmitter 1/4" plug going INTO the opposite end of the 1/4" female to 1/4" female line connector. The WL-20L receiver is then plugged directly INTO the Behringher Powerplay 2 with, of course, a pair of high quality studio headphones coming OUT of the the Behringher Powerplay 2. (The pocket clip on the Behringer Powerplay P2 is super-convenient.) This is how I practice at home. All together this cost significantly more than $100 but I chose to go this route because of the versatility of all of this gear if I want to set up differently, for instance, using the BOSS WL-20L and the WL-50 to go wireless with two instruments simultaneously (me and a collaborator) or even to go wireless with one instrument and, by way of a XLR to 1/4" male converter, one mic. Haven't tried that yet but I COULD without paying $300 for a BOSS wireless mic receiver/transmitter set. (Which I probably will do anyway because I'm sick. SICK, I TELL YOU! This is what Sweetwater can do to a person. Guard your Souls, friends....)

[@ScottUhlMusic]

Nice! If you found something that works for you, that’s the important part. Great setup 👍

[@xSkye24]

Nice DIY hack.. How about the Xvive Audio U4 wireless system. Have you try it? What are your thoughts about it mate compare to this.

[@ScottUhlMusic]

Yup, I did a video on it actually: COMPACT & PORTABLE Wireless In-Ear Monitor System - XVive U4 kzbin.info/www/bejne/j6Swpa2Jqql7Y9k The U4 is meant to be used as an IEM system, so it will be better than this hack for sure. But also a little more $, so it’s up to you 👍

[@donald-parker]

Very cool idea. Can multiple people (each with their own receivers) take a feed from a single transmitter? Any issues if you and your band mates are using lots of these budget wireless systems at the same time? Or even if you are using one for guitar and one for IEM? Those two devices are going to be pretty close to each other.

[@ScottUhlMusic]

1) Not with this system no, this is an IEM hack. Other actual IEM systems do allow that 2) the more wireless on stage, the more of a chance of dropouts. Especially with cheap ones. Cheap wireless have maybe 4 channels available to transmit on. Higher end ones have thousands of available channels and 20-100 can be used at once. So with this IEM hack, I would not recommend using a ton of these. Instead I would look into a cheap IEM system I reviewed here: kzbin.info/www/bejne/mnuvkK1_Z8mliLM 3) using 2 at once shouldn’t be a problem, but it always depends on the wireless environment. But 2 should almost always be fine

[@donald-parker]

@@ScottUhlMusic Thanks!

[@strugs1]

Hi - great video. This is exactly the kind of solution I was looking for, but I have one question. My planned setup is a little different than yours or probably most others, as I do not plan to use my band's mixer as my in ear feed. Mostly because I am only using this for band practice - not gigs. For our practices, the only things that run into the PA are the vocals and keyboards. Guitars, drums and bass are all separate. What I am using currently is a Zoom H2N recorder. I set it up a few feet away from me and it's condenser mic picks up all the instruments and I use its headphone jack output to connect to my Shure ear buds. It works great, but I would like to get rid of the headphone cable by adding the Behringer P1 and the Amoon wireless system to my setup. So my question is - can I simply plug the Amoon 1/4 jack into a 1/4 to 3.5mm adapter coming out of the Zoom mic's headphone out? The issue I am worried about is that the headphone out is stereo, whereas the 1/4 jack is obviously mono. Thanks again - your video was great - easy to follow and your solution is very creative and can save people a lot of money.

[@ScottUhlMusic]

Glad you liked the video. To answer your question, yes it would work. I’m not sure how the stereo to mono would work, as sometimes when you do that you will get only the left or right side. You could also use the adapter out of the P1 as well if you wanted to do that. Also at that point, a cable might just be better. But either way, using a 3.5mm to 1/4 adapter should work no problem. 👍 the mono might be the only problem if you have any

[@strugs1]

@@ScottUhlMusic AH ok - so you're saying that if i use the adapter, it might only send a sound signal to either my left or right headphone? Maybe this would be counteracted by using the P2 in mono made....

[@ScottUhlMusic]

I haven’t used the Zoom before this way, so I’m not 100%, but I’m pretty sure you would be ok 👍 There’s always the Amazon returns if it doesn’t work :)

[@sendalunar2974]

Thank you very much! I have a question. Would you recommend using the headphone out into the wireless transmitter or using the DI out of my amp? Considering I just need to hear myself. Thank you very much!

[@ScottUhlMusic]

You’ll need a headphone amp no matter what to adjust the volume. Whatever it’s coming out of. Just always watch your ears, since this is a DIY hack and not a normal IEM setup 👍 Always test it on low low volume first

[@sendalunar2974]

@@ScottUhlMusic thank you! Will do! I'll try it out for tonight's gig

[@fificap66]

Hi, thank for this video, it's exactly what i'm trying to do! I already have KZ in ear earbuds, guitar wireless CUCAVE 5.8 (ammoon rebranded). I want to use the "line out" output of my guitare amp (that do not mute the amp speaker) to send signal to this in-ear setup. Does the Powerplay P2 really amplify the signal for this kind of earbuds or is it more a level adjustment that lower the signal? And do you know if the Donner EM1 or EM2 can be used live plugged in a powerbank? Thanks

[@ScottUhlMusic]

I did a comparison video for the Behringer and the Donner one here: kzbin.info/www/bejne/p5qahqRjadxgb6c but yes, the P2 definitely amplifies the signal quite a bit so that shouldn’t be a problem 👍

[@fificap66]

@@ScottUhlMusic Thanks. Unfortunately the Donner EM1 or EM2 is out of stock inFrance. I've ordered a powerplay P2!

[@ironblast5]

Not sure if anyone mentioned it here yet but Pro Co. offer a similar system to the Xvive in the more stable 5.8 ghz range for a similar price

[@ScottUhlMusic]

I haven’t heard of that one, as a ton of companies are making these cheaper 2.4 and 5.8 ones. But a lot of them are very similar. I just really like the Ammoon one

[@fabiocaetanofigueiredo1353]

I go with the Sennheiser for Shure 😂

[@ScottUhlMusic]

🤣

[@jamesphillips7211]

Hi Scott. Thanks so much for this. It just might save me a lot of money! 🤞 I just have a couple of questions please... 1. Is it possible to have multiple members plug in these devices and not interfere with each others signal? 2. You often have a 'cons' section to your videos. What is the con with this set up please? Many thanks in advance. 🙏👍😁

[@ScottUhlMusic]

1) you can, but I don’t recommend using a ton of cheap wireless all at once. See this video: kzbin.info/www/bejne/jpjaammojpmHd8Usi=m7nhnk-wsvTfgaQD 2) this isn’t really how IEMs are meant to be used, and you can get pretty afffordable stuff now without this hack. But again, the more cheap wireless on stage at once, the more likely they will get interference. But I also go over that in this video: kzbin.info/www/bejne/jpqVe5aDpNKdh5Isi=7uVBzNBbvjbVPSxa

[@jamesphillips7211]

@@ScottUhlMusic Thanks so much Scott. I actually watched your top 5 things you get wrong with wireless systems right after this and saw that the exact question I asked was in the list! 🥴😂😬 Thanks so much for taking the time to reply and top notch channel! 👍

[@neilkendall9857]

Hi, interesting idea! I have a Zoom L-12 digital mixer which has 5 monitor outputs with built in headphone amplifiers, so up to to 5 musicians can have individual in ear monitor mixes. Would it be possible to use a plug and play wireless guitar system to have wireless in ear monitors with my mixer? I could plug the transmitter into the mixer, but how would I plug my in ears into the receiver, since they're both male jack connections?

[@ScottUhlMusic]

This basically can replace anything that can be replaced with a cable. So yeah, it should work if I understand correctly 👍

[@peterheuer5319]

Honestly, I’ve been using the p2 for two years but running an XLR straight to the belt pack. It’s barely noticeable after a while

[@ScottUhlMusic]

It’s a great little unit for sure!

[@kevinblakely4384]

Hello Thanks for this video. Where to I plug the other end of the xlr cable in my Mixing Desk please?? Is it the Monitor Output? Thanks

[@ScottUhlMusic]

Wherever you are getting sent a signal from. Usually a mixer 👍

[@mickellyrodrigues2191]

P2 can be used in stereo with a Y cable

[@ScottUhlMusic]

See if my answers in your other comment helps you out.

[@baron1c]

Do you have to use the headphone amp or can you just use a quarter inch adapter on the receiver and adapt the quarter inch to eighth inch headphone Jack?

[@ScottUhlMusic]

As long as you have a way to turn up or down the volume of whatever the wireless receiver is plugged into (so you can control volume of your IEM mix), you can use whatever you would like 👍

[@nancam]

Great video! But wouldn't the guitar still have to be wired? Unless you use a second wireless transmitter and receiver for the guitar to be completely wireless? If I've missed a step please help me to see it 🙏

[@ScottUhlMusic]

You would need a separate wireless for the guitar. This hack is for an IEM system

[@nancam]

@@ScottUhlMusic Thought so! Appreciate you and all your content Scott 🙏

[@realmusic4you]

Can you recommend a lower-cost similar wireless system for a singer with effects using an earset microphone?

[@ScottUhlMusic]

Are you asking for a wireless vocal system? Like xlr? If so, I did a video on this one: kzbin.info/www/bejne/nXTKepuiiLVphcU

[@TeamZulueta]

Hi Scott. Thanks for this video. We have a band for our church and currently running P1s with xlr cables for our IEM. If we convert 5 or 6 IEMs with the ammoon wireless rig, will there be any interferance from running 5 of them?

[@ScottUhlMusic]

Almost guaranteed yes. Cheap wireless are meant when you use 2-3, maybe 4 wireless at once. You sometimes can get away with 5 or more, but when you start using more wireless, you have to spend money on the nicer ones that can use more at one time.

[@TeamZulueta]

@@ScottUhlMusic thank you for your quick reply. Maybe the interferance will be minimized or eliminated if i extend the output from the mixer with an xlr cable then plugin the female xlr to female 1/4 inch then plug in the transmitter to separate the transmitters. Probably that would work? :)

[@ScottUhlMusic]

Man, any hack CAN work. But with cheap wireless, the more wireless you run at once the less of a chance that they will work. You won’t know unless you try, but IMO that’s too many cheap wireless on stage

[@ScottUhlMusic]

I would look into these. They are pretty affordable: kzbin.info/www/bejne/mnuvkK1_Z8mliLM And use this trick of one transmitter and 2 receivers: kzbin.info/www/bejne/d2ino6Cgo5upqbM

[@TeamZulueta]

Thank you for your input. We already have bought a setup for wired IEMs. Probably will just get the vocalists for this setup. Thanks again!

[@midway1977]

hi there! I tried a similiar thing with the black amoon 5.8 MHz through a *passive* beltpack. Way not loud enough. Does the active one do a great job??

[@ScottUhlMusic]

Yes, a passive one is going to be much much more quiet than an active one like the P2

[@franciscodominguezguitar2510]

Hi! I want to do this, and I already have 1 Ammoon system, do you think I will have interference problems if I perform with 2 pairs (one for my guitar and one for my inears)?

[@ScottUhlMusic]

All wireless depends on the environment, but I think 2 wireless shouldn’t be a problem. Maybe get the red/wood one and the black one as a second one just to be safe 👍

[@tupirul]

The mono/stereo switch let you listen in one /both sides of the headphones? Most mixers aux are only one side of the headphones

[@ScottUhlMusic]

Yup, check out this video to understand more: kzbin.info/www/bejne/jaHZnImog7anrqM

[@levymichael126]

Hello, thanks a lot for this video. Regarding the wireless device what do you suggest ? Mono or stereo ? Because I use the system with the jack (mono) and I don’t need to pull completely the jack inside the amplifier. If I do that I don’t have a signal in my ears. So not easy to found a wireless stereo with a 5.8 ghz. Thanks for your help

[@ScottUhlMusic]

This diy system is a mono system. If you are interested in a stereo system for somewhat cheap, check out this video: kzbin.info/www/bejne/mnuvkK1_Z8mliLM

[@levymichael126]

@@ScottUhlMusic thanks for your answer my question was regarding the p2. Because when il put a mono jack i don't need to put fully the jack inside to have the sound, if i put it fully i have nothing in my ears. Perhaps i need to change the P2 from stereo to mono ? Thanks

[@ScottUhlMusic]

Oh I see your question now… that’s pretty strange. Yeah try switching it from mono to stereo and see if that works

[@superluchacallejera]

hi Scott . Do u know an easy way to convert stereo to mono audio? in case to take the output from headphones..to use this method... and 2nd what happend if u connect xvive u4 to a stereo output? the xvive convert/sum stereo to mono signal? these are my 2 choices for iem. I like nux iem but too many bad reviews on that. by the way very informative channel..

[@ScottUhlMusic]

You basically have to set it to mono from the mixer (or wherever you are getting the signal from). You need to make sure something converts it to mono, like that switch in the P2 i mention here. Glad you’ve enjoyed the channel! 🤘

[@PocketDrummer]

3:38 - The main reason for me to spend more is to have a limiter. I really don't want blown eardrums.

[@ScottUhlMusic]

Agreed!

[@ianc6741]

Hi, thanks for this. Will there be an interference issue if 3 sets of these are run altogether (1set for Bass player, 1 set for lead guitarist, 1 set for rhythm guitarist)? Thanks.

[@ScottUhlMusic]

If you use that many of a cheap wireless system all on the same frequency, it’s possible. Get one on 900mhz, one on 5.8ghz and one in 2.4ghz would be my advice 👍

[@ianc6741]

@@ScottUhlMusic thanks heaps.

[@skybrat2088]

Good day! May I know if you can use a passive headphone controller like Fischer Amps Mini Bodypack 2 in replace of the Powerplay 2?

[@ScottUhlMusic]

I haven’t used that one specifically, but pretty much any headphone amp will work 👍

[@skybrat2088]

@@ScottUhlMusic Greatly appreciated... Thanks!

[@robbieflower1119]

Hi just a quick question seems the wireless guitar system is mono does the output in the headphones only come out in one ear or both???

[@ScottUhlMusic]

You’ll hear it in both if you set the switch to mono. Find out more in my video here: kzbin.info/www/bejne/jaHZnImog7anrqM

[@robertsesmamusic]

Im trying to get this set up for band practice but also record the feed with an interface. Is there any way thats possible?

[@ScottUhlMusic]

Yeah with a mixer that will work 👍

[@erene9544]

Hi! May I know how to work the Xvive u3 transmitter to the mixer as it uses XLR instead?

[@ScottUhlMusic]

Yeah the wireless xlr would work well for this. Although the Xvive also has the U4 which is actually an IEM system: kzbin.info/www/bejne/j6Swpa2Jqql7Y9k

[@fabricioamansi]

Hi the amnoon transmitter can not be use as a voice in ear? thanks ( for singers)

[@ScottUhlMusic]

For vocals? No, get a wireless xlr instead like this one: kzbin.info/www/bejne/r6SVnn6qZc9qgassi=p_UyTis96gqm98do

[@fabricioamansi]

@@ScottUhlMusic thank you, i mean for in ear. like IN EAR MONITOR. but cheap like AMMOON :)

[@TheJuliokan]

I'll check on this fornmy band but do you know if those wireless systems can run with multiple receivers so we can have the same mix for more than one band member?

[@ScottUhlMusic]

You cannot do that with this system. This is an IEM hack and the wireless cannot send simultaneously to multiple receivers. However, this one is a great price and can do that: kzbin.info/www/bejne/mnuvkK1_Z8mliLM

[@TheJuliokan]

@@ScottUhlMusic Oh yeah, I've watched that video. I asked because a friend of mine wants a wireless IEM system on a budget (on a very thight budget) but I was wondering if this could run several transmitters. For the band, I'd go with the Phenyx, hands down! Thanks again, mate!!!

[@stevehamilton7385]

If you plug the transmitter into a headphone's out of a device....would you really need the P2 at the receiver end?....considering your having an adaptor to plug my headphones into the receiver.

[@ScottUhlMusic]

If you don’t mind going to the transmitter to turn up or down volume. The way to turn up or down won’t be mobile on you in that case. But yes, you could do that if you wanted 👍

[@joshuaplaciego5904]

How about if u have effects pedals?

[@ScottUhlMusic]

How do fx pedals change this?

[@michaeltf6987]

what'd happen if you just use an adapter to connect the IEM's straight to the receiver? You wouldn't have a personal volume adjustment but would it work?

[@ScottUhlMusic]

Yup you can. I do recommend having volume control though. It’s asking for a problem if you do not have volume control

[@michaeltf6987]

@@ScottUhlMusic thank you! Much appreciated

[@marcocabezas6875]

Hola tiene latencia ? Pregunto porque quiero hacer con dos walkie talkie lo siguiente Un walkie talkie le enchufo un mini plug , a ese mini plug le pongo un adaptador para enchufar en una salida auxiliar del mixer y el otro walkie talkie que también tenga el el cable mini plug con si respectivo adaptador que iría enchufado un parlante preamplificado o potenciado por eso quería preguntar si tenia latencia Gracias 🙂

[@ScottUhlMusic]

The more cheap wireless you stack will eventually get latency. But using one usually doesn’t cause latency. 👍

[@maraz2215]

Behringer Headphone Amps was not isolated well so I experienced noise due to the wireless signal. I recommend DONNER with inbuilt chargeable battery

[@ScottUhlMusic]

Dinner is good, but this is the one I recommend the most now: The Best WIRED IN-EAR MONITOR SYSTEM - Fzone P4 kzbin.info/www/bejne/bprXkIGgic6IipI

[@BagusWibisono]

This iem sound good for stages?

[@ScottUhlMusic]

I’ve performed with it multiple times and it works great. But as I say in the video, if I can use my nice sennheiser or this unit, I would use my sennheiser IEM system. This is just a cheap hack to get wireless in ears for only $100 if you cannot afford a nice Shure/sennheiser IEM system.

[@kimlawrenz27]

I'm using maono sound card can I do this in to sound card so I can have wireless monitor ?

[@ScottUhlMusic]

I’m not familiar with that.... but anything that takes a 1/4” cable can become wireless using the method in this video 👍

[@Jeff4014]

Whats the difference between the Xvive4 receiver and trasnmitter and the behringer P2... i don't really get it... the behringer p2 doesn't have a transmitter?

[@ScottUhlMusic]

Behringer P2 is wired. The Xvive is wireless.

[@neutrinou]

Hello! I currently use this technique (Behringer P2 and Ammoon A8 with XR18 console) and I currently have issue, audio starts cracking at higher volume. But if I set volume too low on console output, the transmitter's noise is too noticeable. Is there any way to solve this?

[@ScottUhlMusic]

There are many possibilities. This is a diy hack and it’s not a REAL IEM system. Since making this video I have found this which might help: kzbin.info/www/bejne/i6DVfZ-Vq92Md5Y

[@molnarbalazs2000]

This might be a rookie question but do I need to have the amp on the receiver side? Like my idea is to plug the transmitter into an amp and just connect the receiver to my earphones with a female-female connector, sorry if that's really dumb 😂😂

[@ScottUhlMusic]

No worries at all... and I would highly advise against that because you won’t be able to control the volume in any way if you go that route.

[@molnarbalazs2000]

@@ScottUhlMusic thanks for the advice, and I'm definitely planning on getting the P2 later on, it just doesn't fit my budget right now. Also I have a volume control knob before the transmitter, so if that's not a concern, my setup is technically possible, right?

[@ScottUhlMusic]

As long as you have a way to turn up or down the signal going to your ears, you’ll be good 👍

[@rubensantana3904]

Can i just connect this directly to the back of a piano?? Or no?

[@ScottUhlMusic]

Piano? Do you mean keyboard?

[@town944folk]

Hi Scott. I am very new to this audio game. I have a question. We have a Soundcraft UI24R DIGITAL Mixer that we use at our church. We have the Behringer 1 and 2 that we bought for the preacher's in-ear monitor. The Mike that he uses is wireless. How would we adapt the system using either the Behringer P1 or P2. Could we plug in that transmitter into our P1 OR P2 and somehow have it connected to our Soundcraft UI24R wirelessly?

[@ScottUhlMusic]

Are you wanting him to be able to hear his microphone in in ear monitors? Is that what you are using the P2 for? I’ve never used in ear monitors for speaking stuff, but that is possible to do. You just need to send the signal out of an AUX send on whichever digital mixer you are using. I did a video on that here for the behringer x32: kzbin.info/www/bejne/joLNd5uhhrmJhpo

[@town944folk]

Thanks for the quick reply Scott. Yes that is correct. He says he cannot hear his voice through the three stage monitors and four speakers we have on stage. He wants to hear his own voice that's correct. He tends to move around when preaching so using a cable from the aux to connect to the Behringer is not ideal

[@ScottUhlMusic]

Ok cool, then yeah you need to use the aux send like I do in that video. It should be very similar on the soundcraft 👍

[@town944folk]

Thanks Scott. Will let you know how it goes

[@chazdillon2909]

What size rack do I need for everything? I’m going to start piecing this together. This on on my list and might be missing something. Behringher 2u. Power 1u. Splitter 2u. In ear wireless 1u. My guitar wireless 1u. My helix 2u. Power amp 1-2u. Leave a space for router?

[@ScottUhlMusic]

My advice is to always leave at least 1U of room. Sometimes 2u just in case you want to upgrade 👍

[@chazdillon2909]

@@ScottUhlMusic thanks. Am I missing anything though?

[@ScottUhlMusic]

I’m not sure of your exact setup, but it looks like you have everything 👍

[@steveliberty]

Since the Behringer P2 is still backordered, i was wondering if you know anything about the Donner EM1? Looks like a similar solution. Any good?

[@ScottUhlMusic]

I need to order one to find out. It looks good for sure. The P2 seems to always be on back order all the time

[@ScottUhlMusic]

I just ordered one. I’ll do a video about it soon after it arrives 👍 it looks promising for sure

[@steveliberty]

@@ScottUhlMusic Thanks Scott - I ordered one too. it doesn't really need to do too much to be good I suppose - just play loud enough and clean, and hold a charge for a reasonable length of time. The hard work is being done by the in-ear buds and the wireless dongle. We'll both see.

[@steveliberty]

I just got my Donner. Unfortunately, it doesn’t have a mono/stereo switch. So my first test resulted in me getting audio only in the left channel. After reading the manual, it appears that if i use a mono to stereo plug adapter in between the wireless and the amplifier, it would send the signal to both sides. TBD (I don’t have that adapter on hand).

[@ScottUhlMusic]

Really? I thought it does have a switch. The one I ordered had it pictured anyways

[@DIVA-MC-7]

i might get something wrong but where and how do you plug your instrument if the T/R are already on the in ear setup? you use another pair or cable?

[@ScottUhlMusic]

I’m not sure I’m understanding the question, but if it’s something like my Hx Stomp, i can plug the wireless into one of the outputs and then plug the receiver part of the wireless into my ears in order to hear my hx stomp/guitar 👍

[@DIVA-MC-7]

@@ScottUhlMusic your Stomp is some kind of IEM interface( because I don't have one)? I would like to be able to play wireless in my house but not disturb anyone. I will sometimes play on my computer via audio interface like m-audio solo or use my small instrument amplifier. I don't understand where you get the sound to come to you with just a pair of wireless plugs. Where is your instrument plugged ? 🤔I use an active bass.

[@ScottUhlMusic]

With your setup, and using this IEM hack, plus the transmitter wireless into the Output if your audio interface, and then plug the receiver of the wireless into the headphone amp 👍

[@DIVA-MC-7]

@@ScottUhlMusic thank you!

[@spiral0112358]

I have a Headrush Looperboard and want to connect my Looperboard, guitar, and IEM together wirelessly just for practice without disturbing the wife. Is that possible with a single set of Transmitter and Receiver with all the bells and whistles that are provided by the Headrush or would I need 2 sets to make it work? I'm new to all this so sorry for sounding like a noob

[@ScottUhlMusic]

You can use this setup for sure to run a direct out of the Looperboard to your headphone amp that your IEM's are connected to (like this video). For sure. If you want the guitar to be wireless as well, you'll need another set of wireless. Cheers!

[@spiral0112358]

@@ScottUhlMusic sweet! Thanks for the quick response dude! You are awesome!

[@mickellyrodrigues2191]

What if I wanna use stereo with this same set up ? Which receiver and transmitter do I've to use ?

[@ScottUhlMusic]

To do this in stereo, you would need two wireless transmitters, which wouldn’t really make sense and I would recommend getting a system like the video I’m going to debut on Monday. I’ll post a link once it’s available. But I guess you could get two of the Ammoon systems and have the Donner EM2 attached to your belt with 2 of the Ammoon sticking out. But if you truly need stereo IEMs I would recommend getting a different system.

[@ScottUhlMusic]

Also, I just realized... are you asking because you think Mono will be just in one ear? If so, that’s not the case, you still get your mix in both ears, you just don’t get to pan the sounds left or right. So when I did run a stereo iem setup, in my mix I put my vocals dead center, lead vocals panned right, drummer vocals panned left. It was nice to have the separation but overall I ended up just switching back to mono and having everything in my ears that I wanted without panning. So mono doesn’t mean “only one ear.” Thats why the P2 has that switch. If you are getting signal into only one ear, set it to “mono” and it fixes it.

[@mickellyrodrigues2191]

I know that mono doesnt mean just getting the mix in 1 ear. I use mine and pan what's on my right to the right and same for the left keeping the bass n the whole drum kit in the centre I get good separation . But the p2 have a TRS input put so if the boss wireless system is used with a Y cable on the transmitter as the Boss has TRS Jacks on both the sides so will it work in stereo n will I get my stereo mix?

[@mickellyrodrigues2191]

Do you have any suggestions for affordable wireless iem systems which works in stereo?also thanks for ur advice

[@ScottUhlMusic]

Gotcha. I get asked that “mono” question a lot, so I figured I would check. My guess is that it will NOT work since the Ammoon wireless is a TS like most guitar cables. So I don’t believe so, but you can try it and let me know. I’m curious if it would, but I don’t believe so.

[@bauer6105]

Are you not using a limiter or do you know of options for only a limiter in a setup like this? I have a submixer on stage and from there i can go in my iem but im scared without limiter...

[@ScottUhlMusic]

You won’t have a limiter with this, which is why I say to be cautious doing something like this since it’s an IEM hack

[@ScottUhlMusic]

This is almost the same price as this: kzbin.info/www/bejne/n6qqhIWvibyVnqc