I'll just leave this here, I used this on my personal car, I drive 40k miles a year and it is very hard to keep my cars looking good. But this, this really works. Application was 6 months ago, I've driven 22k miles since then and protection is still very much evident, and it's made the car so easy to clean since. My last car had one of your previous generation coatings on which did the job, but was a pig to apply, very grabby for weeks afterwards and didn't hold up as long. Pure Evo by comparison went on like a dream, didn't waterspot as badly and is still doing the work. Pulling the car into the garage and giving it a cancoat refresh tomorrow ready for the deep winter. Great product and glad I took a chance on it!
@neilwalker50412 жыл бұрын
This is an amazing product but I am still confused with PURE and MOHS. What are the differences between the two as far as gloss hydrophobic behavior?
@stephenlouden48010 ай бұрын
don't knots if I didn't use enough I coated a small suv volvo xc60 brand new. I used half my 50 ml kit probably 20 mL. cleaned with Meguires Hyper Wash, Iron X, clay mitt, then Gyeon Prep and coated one whole panel at a time knowing it's forgiving I have 5 min then leveled really easy used 1 low pile microfiber to get it off and second blue high pile one to get it perfect. it didnt go on thick though ...just enough to be even and fully cover the panel. I also put another, I guess, light coating on the front end because I was wondering if I put too little on.? we'll see in a couple weeks when I do 1st wash. definately love the gloss and ease of use though. hope I used enough
@tredfxman Жыл бұрын
Application: The problem does Not reside in not having enough coating. The problem resides in 2 things: 1. Seeing the coating once you remove it! (It is very hard to see) 2. 10 minutes flashing time is a joke, if your working in over 20 degrees: Even if using several towels, example 1 for each panel, there seem to be a possibility for it to leave smudgy stains. (Granted not 100 % sure this was coz of preparation products i used). But in my opinion the hard thing with this product is that in summer, it has to be removed very quickly after application! And while doing so, it is utterly important to swap to a clean destination of your towel on every wipe! & swap towel after 1 panel or so! 👍
@bdcd16 Жыл бұрын
Hey, Jeff, thanks for the video. I had been looking into MOHS EVO and received a bottle for Christmas. I am wondering if Pure might be better for my Soul Red Mazda 6. From what I can gather, PURE is darker and deeper, and MOHS is glossier, but not as deep. Pure is better visually, but MOHS is slicker. Both are supposed to be kept up with ceramic detailer. How do they compare after ceramic detailer? Is pure as slick now? Is Mohs as deep? Thanks
@BrandonsGFX2 жыл бұрын
Can this be used on wheels, trim, headlights and glass? Including windscreen?
@GYEON_official2 жыл бұрын
Yes but NOT on windscreens. All other parts will be fine. Regards, Y.
@jeremyogburn58882 жыл бұрын
You said if you want to apply multiple layers, get a 50ml bottle. Does this product benefit noticeably from multiple layers? The gloss enhancement is what drew me to this product, so mainly my question is would the 2nd layer add any noticeable amount of gloss than a single layer?
@GYEON_official2 жыл бұрын
No, it will not. Regards, Y.
@Bull1the1Great2 жыл бұрын
Hopefully to get my hands on one soon
@dandropsgears46142 жыл бұрын
How long, until I can introduce water to it? I finished coating a car yesterday, around 3pm. Right now it’s 8am the next day, would it be okay to test some of the panels with water to make sure it’s bonding properly and make sure the water is beading off?
@GYEON_official2 жыл бұрын
This test will not bring you any valuable answers, yet, on the contrary, will add the most unwanted factor to a freshly applied coating. Just don't do it. A freshly applied coating always beads worse than a dry/cured one. If you missed a spot, you will have to re-apply probably the whole panel anyway and there shall not be a huge difference whether you do it now or in a weeks time.
@dandropsgears46142 жыл бұрын
@@GYEON_official Oh okay! Thank you for the response! I just looked at it this morning, and it looks absolutely amazing! I think, I’m just a bit impatient when it comes to the curing time lol!
@ryeguy012 жыл бұрын
How would you compare Pure's appearance to Can Coat?
@GYEON_official2 жыл бұрын
Q² Pure will have a warmer candy and more wax like look. Top it with Q² Cancoat for some extra gloss. Remember though, quality polishing and meticulous preparation are as important if not more important for a stunning end result. Regards, Y.
@colinmcburnie28812 жыл бұрын
I’ve just put can coat evo on my van and wow brilliant very happy with it is this much the same to work with? As thinking of doing my bmw with this
@GYEON_official2 жыл бұрын
Q²Pure will need a bit more time to do the whole car but it will give you also a bit more time in the wipe off process. Remember that the preparation and working clean are the two most important things for a great end result. Regards, Y.
@colinmcburnie28812 жыл бұрын
@@GYEON_official thank you I get the prep polished and prepared a few cars but not used coating just polish waxes and spray coatings but decided to go with Mohs evo rather than the pure as watched video saying this is better for lighter cars and my car is white. Is this correct ?
@googlereviewer27434 ай бұрын
can I apply this on glass roof because I really want to protect it from most tree sap and bird droppings. Thanks
@GYEON_official3 ай бұрын
First of all, a coating will not “protect” against bird droppings and tree sap. It will make the removal easier but if you know that bird droppings can etch the metal under the base coat, then a less then a micron thick coating will not prevent that. For glass we have Q²M View or Q²M QuicView which would be a better route to go. Regards, Y.
@gregvarano30442 жыл бұрын
Can Pure EVO be applied to plastic trim and headlights?
@GYEON_official2 жыл бұрын
Yes it can and will perform very well. Regards, Y.
@agdom55962 ай бұрын
I'm live in Asia where the main problem is water spot, due to almost every day rainy on the morning then evening extremely sunny 35-37°c and road grime such as tar, bug and etc adhered on lower side panel after rain.. Which do you prefer between this Q² pure evo and Q² mohs evo?? Hope GYEON can answer and guide me to choose the right product.
@GYEON_official2 ай бұрын
In Asia, for example Singapore Q²Pure EVO is probably the most preferred coating for that reason. Regards, Y.
@agdom55962 ай бұрын
@@GYEON_official thank you 👍.. Will try it
@user-bf6go9nf6g2 жыл бұрын
What is the best practice with Pure Evo… to wipe right away, after 2 or 3 min, or wait until it starts to tack? Is there better bonding and performance if you wait longer to wipe off? Thank you!!!
@GYEON_official2 жыл бұрын
Did you watch the video carefully? It’s possible to even wait 10 min. before wipe off. It will not tack at all. Working in stable conditions and with a fresh bottle is important to benefit from this window before coating removal. Regards, Y.
@user-bf6go9nf6g2 жыл бұрын
@@GYEON_official I did watch carefully. I guess I was not clear. What I’m getting at is there any benefit to waiting? For example if I apply to a panel and am done applying after 2 min, should I go ahead and wipe or is it better to wait closer to 10 min to wipe? In other words if I wait 10 min will the coating be more durable? Thx!
@GYEON_official2 жыл бұрын
Ok, there is no need to wait for 10 min. It’s a benefit for you as a user. There is sweet spot, in stable conditions a wipe off after 3 to 5 minutes is working fantastic. Regards, Y.
@eraclefigliodizeus4 ай бұрын
On a Daytona Gray Audi RS (dark gray), do you recommend Mohs or Pure EVO? Thanks
@GYEON_official4 ай бұрын
Both will look great. Again, the final result lies in quality polishing work combined with proper preparation. Everybody has different expectations but personally on that colour I would choose Q²Pure Evo. Regards, Y.
@oec88 Жыл бұрын
Can I apply additional car body wax on top of this coat for additional or better protection?
@GYEON_official Жыл бұрын
Do you mean on a freshly coated car or rather a coating that has been on it for a while? In the last case I suggest to use Q²M Restart as a shampoo and some Q²M Wetcoat. Regards, Y.
@oec88 Жыл бұрын
@@GYEON_official I mean after a car that is being freshly coated, and apply other car body wax for additional protection.
@GYEON_official Жыл бұрын
It can be an option if the car needs to leave the studio in bad weather. I can’t speak for every single wax on the market but Q²M Wax will work great. Regards, Y.
@ericrobinson2842 жыл бұрын
Can you use Pure on chrome,plastic,& glass? Do you need to add Cure after the Pure application?
@GYEON_official2 жыл бұрын
After a Q² Pure application I always suggest to use Q²M Cure before the car goes outdoors. For plastic, chrome and glass I would stick to the dedicated products for these surfaces. Regards, Y.
@MiataPower96 Жыл бұрын
Can Pure Evo be applied to any other non painted surfaces? Such as glass, plastic trim, or alloy wheels?
@GYEON_official Жыл бұрын
You can use it on different surfaces like trim and wheels but not recommended on glass. Regards, Y.
@salitomi2 жыл бұрын
I’like to ask you about your opinion of a new car’s first protection. Car is straight from the factory line(dealership), fresh paint etc. Do i have to wait several weeks or months till the fresh paint gets hard, gas out and dry or after driving home from the dealership i can apply a layer of protection coat e.g. Gyeon Pure Evo or Gyeon Wax? What is your recomendation? Thank you for your answer! Best regards! Tom from Hungary
@GYEON_official2 жыл бұрын
Hi Tom, Your “new” car paint is already several weeks old so no worries. Your kind of protection is personal and depends your expectations. Both Q²Pure EVO or Q²Wax will have great results. Regards, Y.
@salitomi2 жыл бұрын
@@GYEON_official thank you!
@time2shineautospa5862 жыл бұрын
After applying, how long is the cure time? And should I apply the quick detailer immediately after the cure time?
@GYEON_official2 жыл бұрын
Cure and dry are 2 different things. Dry in 24h to be good. Curing can take up to 3 weeks. After dry time Q²M Cure or Q²M CeramicDetailer are the preferred choices. Regards, Y.
@time2shineautospa5862 жыл бұрын
@@GYEON_official thank you for that comment! Correct me if I’m wrong but 12 hours is the approximate dry time for Pure? I may need to leave vehicle out over night and worried about dew. Can I put the Ceramic Detailer on before I park it outside overnight if I let the vehicle dry for as long as possible that day in the garage?
@GYEON_official2 жыл бұрын
You can but again: the longer the wait inside, the better. I have no control over your environment! Regards, Y.
@Nver912 жыл бұрын
Hi Y, How long is the dry time before it is safe to have contact with water or rain? And how long before I can apply q2m cure? Thanks!
@GYEON_official2 жыл бұрын
Hi, a minimum of 12h but the longer the better. Apply Q²M Cure the moment before you are gonna send the car out. Regards, Y.
@Nver912 жыл бұрын
@@GYEON_official thank you for the very quick response! 👌🏼
@Enselladus2 жыл бұрын
I'm looking at getting some PPF on a couple of panels my car, I know you do a dedicated ceramic coating for PPF but will Pure work okay on PPF? I don't want to have to buy two different ceramic coatings for one car.
@GYEON_official2 жыл бұрын
Hi, it will work but it’s absolutely not recommended! Not to push you in any way but the new Q² PPF EVO is amazing, don’t think short term. Go for it, you will have zero regrets! Another option is to use GYEON PPF PROTECT+ which already has a hydrophobic topcoat build in, is selfhealing and has stunning clarity. Choose wisely. Good luck. Regards, Y.
@easynow34782 жыл бұрын
Can you reapply anther layer ?say after a week ? I still have few panels left to do but was thinking about 2nd coating the bonnet as not sure if applied thick enough, it’s been a week since
@GYEON_official2 жыл бұрын
As mentioned in a previous comment we recommend to use Q²CanCoat EVO as a topper and fur sure if it’s at a later date. Regards, Y.
@easynow34782 жыл бұрын
@@GYEON_official thanks car looks amazing 🤩 definitely recommend pure evo was easy to apply and wipe off, I just seem to have quite a lot left so going to second coat few areas 😉 can’t wait to apply can coat evo over the top once I’ve finished thank you 🙏🏻
@oCaptainKorma2 жыл бұрын
Can I use pure evo, then top off with cancoat?
@GYEON_official2 жыл бұрын
For sure! Great combo! Regards, Y.
@NoirSavant2 жыл бұрын
So it wipes off easier than the old one? That one was a lot of work
@GYEON_official2 жыл бұрын
Give it a try, some things can be very subjective and varies depending environments. Regards, Y.
@Will-ch8zt2 жыл бұрын
Is the car smooth after applying Pure or do you recommend applying CanCoat or Ceramic Detailer?
@GYEON_official2 жыл бұрын
I recommend applying Q²M Cure or Q²M CeramicDetailer before sending the car outside. Regards, Y.
@waynebuckley6633 Жыл бұрын
do you have to use cure after?
@GYEON_official Жыл бұрын
We certainly recommend to use Q²M Cure 12h after the application especially if the car goes out in rather bad weather conditions. Regards, Y.
@darhkbloom5089 Жыл бұрын
Can i wash and reuse towels after applying this coating or no
@josephgilbert18562 ай бұрын
I would toss them to be safe :/
@GYEON_official2 ай бұрын
You still can use them for different purposes such as engine bays or wheelarches. No need to toss them. Regards, Y.
@ronsilco39772 жыл бұрын
Can this be used on glass and or chrome wheels?
@GYEON_official2 жыл бұрын
We do not recommend that. There are dedicated coatings for glass like Q²View or Q²QuickView. On chrome wheels we suggest the use of Q²Rim. Regards, Y.
@rover13742 жыл бұрын
Do I need to use Cure if I can keep the car indoors for close to a week? Or can I use the Ceramic Detailer?
@GYEON_official2 жыл бұрын
One week indoor is great. Q²M CeramicDetailer will be fine. Regards, Y.
@rover13742 жыл бұрын
@@GYEON_official better to wait as long as possible to put on the Ceramic QD or Cure? Eg if I can keep the car Indoors for 6 days, put it on the 6th day rather than 12 hrs after?
@GYEON_official2 жыл бұрын
The longer you can keep the car inside without adding anything, the better. Regards, Y.
@rover13742 жыл бұрын
@@GYEON_official thanks! I’ll add cure or the Ceramic QD at the latest possible stage.
@rover13742 жыл бұрын
Just wondering what the timeframe is for doing a second layer Pure? Is a second layer second layer beneficial, and how long is too long for that second layer?
@easynow34782 жыл бұрын
How many set of 2 towel would you recommend for your average car ? Would one set do the job ?
@GYEON_official2 жыл бұрын
I would recommend to use 5-6 towel for the application of Q² Pure EVO. You better be safe then sorry. Regards, Y.
@easynow34782 жыл бұрын
@@GYEON_official thanks 🙏🏻 is that 3x soft wipes and 3x bald wipes or 6 of each ? Also best place to order the 2 different gyeon towels I’ve already got the pure evo ready to go 🫡
@GYEON_official2 жыл бұрын
4 Q²M BaldWipes & 2 Q²M SoftWipe will be the perfect setup. To find your closest GYEON Shop have a look here: gyeonquartz.com/network/ T.
@easynow34782 жыл бұрын
@@GYEON_official thanks t 🤞🏼 I get it right 😂
@johncooper77512 ай бұрын
Should I throw away my applicator pad after using?
@GYEON_officialАй бұрын
After your application it will harden up and not be possible to use again. You can potentially wash it immediately in hot water and use the applicator as a sponge or cleaning tool but not on paint. Regards, Y.
@Life_with_an_alfa_romeo2 жыл бұрын
Great product and great video! 👍 Question: Can you wipe/buff off immediately after applying, or do you need to wait a bit? Also, can you use the applicator for the entire car to coat?
@mikea31692 жыл бұрын
Yep, you can wipe it off immediately after applying; the coating bonds to the clearcoat almost immediately. No harm in letting it sit for a bit though; as long as it doesn't start getting really grabby upon removal.
@GYEON_official2 жыл бұрын
In stable conditions you can wipe off after you have covered your section. Reaction and bonding is already there after 10-15 seconds. One applicator for a whole car is not what I would recommend. Depends of course the aize of the car but a minimum of 3 would be my go on a normal sized car. Regards, Y.
@kelvinrian2792 жыл бұрын
Acompanho do Brasil, sempre uso os produtos de vocês. Excelente, recomendo.
@clou19692 жыл бұрын
What’s the maintenance needed with Pure?
@GYEON_official2 жыл бұрын
As with any other coating. We made a video about that as well: kzbin.info/www/bejne/aoCxk5Z-e89jo8U Regards, Y.
@tylerhope7522 жыл бұрын
How does it go ontop of Q2 Primer?
@GYEON_official2 жыл бұрын
Perfectly smooth. Regards, Y.
@tylerhope7522 жыл бұрын
Awesome, will be correcting and coating my car soon, with cancoat on the windows and plastics of my black mazda 3
@GYEON_official2 жыл бұрын
Cool. Just don’t do Q²Cancoat on your front windscreen, Q² QuickView is the way to go. Regards, Y.
@tylerhope7522 жыл бұрын
Might i ask why Cancoat is not good on the front windscreen?
@punjabisole232 жыл бұрын
I HAVE TWO QUESTIONS: CAN I APPLY 4 LAYERS OF GYEON EVO THEN APPLY A TOP COAT SUCH AS CARPRO GLISS OR GYEON SKIN? AND CAN I SPPLY THIS ON GLASS AS WELL INCLUDING THE WINDSHIELD?
@TrVlogs822 жыл бұрын
Bruh is that a freaking M3 E36 in the back?! Sorry car enthusiasts.