A Look At A Johnson / Evinrude 4, 5, and 6 HP

  Рет қаралды 59,715

Brandon's Garage

Brandon's Garage

Күн бұрын

Пікірлер: 59
@Murphy_13507
@Murphy_13507 4 ай бұрын
Just picked one of these 5hp 11r long shaft up today. Tomorrow I’m grabbing a 4 hp 96 Johnson sea horse with under 100 hours on it for 500 Canadian Great info with this video. Keep the vintage motors going. They have life left!! Cheers !!!
@edwardcreel4571
@edwardcreel4571 3 жыл бұрын
They make a screw on transom that sets up 6 inches you can put on and off that way you can run a long shaft
@HERRxc
@HERRxc Жыл бұрын
I just changed my longshaft to shortshaft by cutting the main driveshaft. Suzuki 5hp 4 stroke
@gunfisher4661
@gunfisher4661 3 жыл бұрын
Johnson had that kind of versatility with a few motors like the 84 7.5 hp that I have about the only difference was the carburetors vs a 4 hp.
@brianbaker2484
@brianbaker2484 5 жыл бұрын
Could you do a lower tear down on the 6hp? Would be greatly appreciated
@topazviper
@topazviper 4 жыл бұрын
Did you end up taking this apart and repairing it? I just bought the same motor (except 1965) and this is my first time trying this. Your videos have been so informative, it would be great for me to have one to follow along with.
@svbiker2006
@svbiker2006 3 жыл бұрын
Hey. I use an Johnson 6.0 BJ6DREDS 1996. Which 2-Stroke fuel mix do i have to use? 1:100, 1:50, 1:25? Greetings from Germany.
@jimmysapien9961
@jimmysapien9961 2 жыл бұрын
50:1 synthetic oil
@rainerneumeister5239
@rainerneumeister5239 4 ай бұрын
Do you know anything about the johnson 2.5 hp twin cylinder. Is it the same as the single cylinder? Performance , power wise. ?
@jeffperkins6514
@jeffperkins6514 4 жыл бұрын
Great videos. I've got a 1990 4hp deluxe and you helped me get the pull rope mechanism working correctly. Should my 4hp Deluxe have some type of air box covering the carb? All I have now is the carburetor inlet open with nothing covering it.
@BrandonsGarage
@BrandonsGarage 4 жыл бұрын
No sir, nothing but a little choke knob bracket.
@jeffperkins6514
@jeffperkins6514 4 жыл бұрын
@@BrandonsGarageThanks!
@jimmysapien9961
@jimmysapien9961 2 жыл бұрын
Thank you very good information 🙏
@bongsoun5683
@bongsoun5683 4 жыл бұрын
I have a 6hp when u put it in gear it only about half of the rpm of when it’s in neutral full throttle
@BrandonsGarage
@BrandonsGarage 4 жыл бұрын
check to see if its only running on one cylinder?
@bongsoun5683
@bongsoun5683 4 жыл бұрын
@Brandon's Garage how can I do that ? & thank you for replying and helping
@donaldadams7935
@donaldadams7935 5 жыл бұрын
Help! Need a video or basics on how to disassemble a steering tube on a 15 hp Johnson...very stiff to turn. Thank You!
@kaivank
@kaivank 5 жыл бұрын
I just got the Johnson 6HP workshop. Exactly the above video model..in India. Not used for over 12 years. Would need your help...it Haas 2 fins on the gearbox with the skedge
@BrandonsGarage
@BrandonsGarage 5 жыл бұрын
Well, they all do.
@lupegalvan9993
@lupegalvan9993 4 жыл бұрын
I saw your recoil video. Will most likely have to do that. I’m new to outboard motors. Last time I launched on a slow river it didn’t have the power to go up river. I think a 4hp evinrude should be able to go up slow current. Any ideas where I should start problem solving? Thanks
@AaronGoSoFast
@AaronGoSoFast 6 жыл бұрын
I've been trying to get my grandpa's old '79 johnson 15 hp outboard engine running. It ran when it went into storage, but it's been sitting for over 15 years. I am extremely green when it comes to boat engines. Aside from changing the water pump and gear oil, is there any other critical parts that need overhauled before trying to run it?
@BrandonsGarage
@BrandonsGarage 6 жыл бұрын
Not really, no. Not if it was put away correctly. (storage; winterizing, or running it out of gas)
@BrandonsGarage
@BrandonsGarage 6 жыл бұрын
Not really, no. Not if it was put away correctly. (storage; winterizing, or running it out of gas)
@jimmysapien9961
@jimmysapien9961 2 жыл бұрын
@@BrandonsGarage I agree, I run out all my gas ⛽️ before I shut it down -
@jeffmarsh6363
@jeffmarsh6363 3 жыл бұрын
Hi, I just replaced my coils on my six hp. One cylinder was cutting out. Also throttle was hard to turn. Replaced coils, no spark either cylinder. Followed ignition wires around. Both broke off at the clamp next to starter. Replaced ignition wires one at a time. Had to removed new coils again. Checked I had spark with gap tester. Fueled her up and now get a backfire? Long ignition lead is going to top cylinder. Shorter lead by starter assy goes to bottom cylinder. Any thoughts? I did notice my points were gapped to about 0.014 vs 0.020 spec. It was running fine last year so did not want to mess with that. Any advice appreciated.
@whitebuffalo4641
@whitebuffalo4641 6 жыл бұрын
Thanks for all these videos. I have a 2000 Johnson 25 and a '71 Evinrude 6. The 6 has a puzzling situation going on. When the tank to motor hose is disconnected a small amount of fuel spills from the fitting on the lower cowling. Some of the fuel in the hose running from the connection fitting to the screen cover on the fuel pump runs out. I took that fitting off and found that there is no check ball in it, nor does it appear that one ever existed. Did the older small motors not have a check ball there? Thanks
@BrandonsGarage
@BrandonsGarage 6 жыл бұрын
Correct they all do this. Turns out that valve wasn't invented until some point in the 80's
@whitebuffalo4641
@whitebuffalo4641 6 жыл бұрын
@@BrandonsGarage Thanks for taking time to explain and saving me $50+ bucks only to discover that the new one also had no check ball. I really appreciate your low hp Johnson/Evinrude videos!
@tiago6282
@tiago6282 4 жыл бұрын
Good afternoon friend. I am Brazilian I would like to know. the right regulation used in the johnso 6 hp air regulation mixes if it is 2 and a half turns.
@harrycarlock800
@harrycarlock800 5 жыл бұрын
would like to see videos on a 1987 e6rcud. i have one that just is not running right and i would like to fix it.
@captainsamA320
@captainsamA320 4 жыл бұрын
I’ve a good question I’ve a 4hp but i wana put an 8hp carb they are basically the same with different jets how well will that work
@BrandonsGarage
@BrandonsGarage 4 жыл бұрын
Not at all, much larger pistons on an 8hp than a 4.
@captainsamA320
@captainsamA320 4 жыл бұрын
@@BrandonsGarage hm some mods might need to be done
@mred3608
@mred3608 6 жыл бұрын
Really interesting Brandon. All your videos are really helpful and informative. I have an evinrude 1966 6hp with only about 10hrs on it. As a newbie can I ask you how often do the gearbox seals need changing. Is it every couple of years?
@BrandonsGarage
@BrandonsGarage 6 жыл бұрын
once ever 10. Give the age of the rubber in yours, they probably need to be changed. As does the water pump. Watch my 9.5 Lower Rebuild video. Exact same process.
@jessedavidson2827
@jessedavidson2827 6 жыл бұрын
Brandon, I have a johnson 9.5 that wont stay in gear while running. What would cause that?
@h-townfishing1382
@h-townfishing1382 4 жыл бұрын
hey i have a 6hp johnson and it has trouble starting but when it does start it runs great. any tips?
@BrandonsGarage
@BrandonsGarage 4 жыл бұрын
check compression? And what is your starting process?
@h-townfishing1382
@h-townfishing1382 4 жыл бұрын
Brandon's Garage pull choke and put it on start and pull. The guy that I got it from said he put the wrong gas/oil ratio in to. But he got it starting great.
@h-townfishing1382
@h-townfishing1382 4 жыл бұрын
The guy know how to start it. What’s a good sequence to start the engine?
@jimmysapien9961
@jimmysapien9961 2 жыл бұрын
@@BrandonsGarage exactly
@jimmysapien9961
@jimmysapien9961 2 жыл бұрын
@@h-townfishing1382 yes put in right oil /GasRatio - new Plugs 🔌 too - also before shutting down Engine -unplug fuel line and run out gas . 👍🏻
@robinpettey8676
@robinpettey8676 4 ай бұрын
Left handed rotation prop
@Erkan-nb8fo
@Erkan-nb8fo 5 ай бұрын
Bu motor kac zamanli ?
@lunchlinger
@lunchlinger 4 жыл бұрын
I wonder how you get the carb off?
@liljoe9156
@liljoe9156 5 жыл бұрын
I Have a 5hp Johnson motor. By any chance do u know where can I buy a 8 by 7 1/2 .. 3 blade propeller. Thanks in advance.
@marcoromero2964
@marcoromero2964 2 жыл бұрын
I have a 5hp and need help won’t start
@rgboyte
@rgboyte Жыл бұрын
Wow !😊
@trinidadvictorino9365
@trinidadvictorino9365 4 жыл бұрын
So i rebuilt a 6 hp carb and noticed down in the slow speed need some fiberous material by needle seat orfice is this normal?
@brianchisnell1548
@brianchisnell1548 4 жыл бұрын
Packing. To seal the needle.
@richardd3663
@richardd3663 5 жыл бұрын
This is SO frustrating! I'm all over youtube trying to find how a 2 blade prop is fitted, you guys just don't seem to want to cover props!
@BrandonsGarage
@BrandonsGarage 5 жыл бұрын
New video I just posted might help you.
@BrandonsGarage
@BrandonsGarage 5 жыл бұрын
New video I just posted might help you.
@richardd3663
@richardd3663 5 жыл бұрын
@@BrandonsGarage Do you mean the video 'Where power meets water'? I couldn't find the 6hp 2 blade prop anywhere in that one. But never mind, it proved quicker to go and remove it and have a look. I still cannot understand why this all important part of an outboard is so ignored on youtube. You all (Americans) seem too obsessed with three blades and going as fast as possible! However, I did find a much shorter tutorial on prop types and their usage. Many thanks.
@richardd3663
@richardd3663 5 жыл бұрын
@Russ Gallagher Oh dear, yet another case of two nations divided by a common language! My point was, and I've solved it now, was that I couldn't find any videos showing how to remove a 2 blade prop, they were all 3 blades. End of discussion!
@kee1810
@kee1810 3 жыл бұрын
@@richardd3663 you’re a bum. Grow a pair and do it without a video.
@svbiker2006
@svbiker2006 3 жыл бұрын
Hey. I use an Johnson 6.0 BJ6DREDS 1996. Which 2-Stroke fuel mix do i have to use? 1:100, 1:50, 1:25? Greetings from Germany.
@BrandonsGarage
@BrandonsGarage 3 жыл бұрын
1:50
1970's Evinrude 6 HP; Various Repairs
1:18:41
Brandon's Garage
Рет қаралды 88 М.
How to treat Acne💉
00:31
ISSEI / いっせい
Рет қаралды 108 МЛН
Леон киллер и Оля Полякова 😹
00:42
Канал Смеха
Рет қаралды 4,7 МЛН
6 hp Johnson Sounds Good Runs Cold pt. 7 - THIS OLD OUTBOARD
18:16
THIS OLD OUTBOARD
Рет қаралды 2,8 М.
1979 Johnson 6hp low compression Part 1
22:20
Woody's Garage
Рет қаралды 3,9 М.
Will This Abandoned Outboard Run Again?
16:26
ThatBoatGuy
Рет қаралды 1,2 МЛН
1975 Johnson 25hp Outboard Motor Lake Test
8:04
Old JohnnyRude
Рет қаралды 20 М.
Johnson Evinrude 6 HP Lower Removal and Seal Explanation
14:31
Brandon's Garage
Рет қаралды 60 М.
1979 Johnson 6hp no spark, fixed? Part 4
22:36
Woody's Garage
Рет қаралды 3,1 М.
Johnson Evinrude 4 HP Deluxe - Lets Get It Running
47:12
Brandon's Garage
Рет қаралды 34 М.
Johnson Evinrude 6 HP Shift Handle Removal
27:20
Brandon's Garage
Рет қаралды 33 М.
How to treat Acne💉
00:31
ISSEI / いっせい
Рет қаралды 108 МЛН