A Mud Pit Method for Reconditioning , Boring and Honing of 3 Cylinder Engine Block

A Mud Pit Method of Reconditioning , Boring and Honing of 3 Cylinder Engine Block
#engineblock #machineshop #machinist #cuttingedgetechnology #amazingtechnology #manufacturing #pakistanitruck #canadiantruck #americantruck #engineblockboring

[@ManiacRacing]

It's all about heat control when working on cast iron. Mud pit is simply to hold the heat and control the cooling. These guys might look primitive, but this kind of work is actually quite technical, and most welding and fabrication shops in the first world won't even touch this kind of repair due to the difficulty and risk of cracking the casting.

[@Dirkathesergal]

Они точно в постапокалипсис не пропадут и дадут всем фору. По сути они уже всю жизнь в приближенных к нему условиях оживляют машины и механизмы. Так что для них врятли сильно что-то поменяется, ну разве что они смогут обновить свои станки нахаляву. Честно, не перестают удивлять. Правильно говорят, кто хочет, тот ищет возможности.

[@user-cp8zc2xc7z]

Капремонт на глазок.

[@SaeedSaeed-vt6om]

Cool work thanks 👍

[@user-gt7kc7pw6r]

Да ребята не парятся. Колено зажимает, проблема решаема! Просто отпустить болт на крайнем бугеле.

[@DiscoveringSkills]

Yes but it’s difficult job

[@_tot_ruslan_]

Ну там его плоскостью по бетону таскали😂 и собирали без пасты) на сухую😂 а вось, неделю поработает.

[@user-cc9hi3kt4u]

@@_tot_ruslan_ мы змз 402 также в сарае собирали, 5 лет проработал около 70т км ,продали живым.

[@user-cp8zc2xc7z]

@@_tot_ruslan_ Когда его по бетону таскали я плакал...

[@user-rl8yp6it7s]

объясни, зачем они большие конусные дырки между цилиндров насверлили и заварили потом?

[@makarandkulhalli4193]

Very skilled. Where is this?

[@frankE91210]

interesting dish to the pistons

[@hitzoneproductions7858]

Why is there trash everywhere? Despite, they did an amazing job. Respect!

[@andruhalift]

Если им дать современные технологии, они ракеты за неделю собирать будут 😂

[@_tot_ruslan_]

Только летать они будут в бок с таким подходом😂

[@Canal-Rouler]

j'aimerai tellement savoir faire tous ça ..

[@buddyjohn]

@32:01 they didnt put any sealing rings on those pistons & yu could see there were provisions for thm

[@JohnnyAFG81]

It’s archaic, but they get it done in the end

[@bobbofly]

They sure do a lot of those Massey tractor threes.

[@DiscoveringSkills]

Yes 🙌

[@Alaska_Engineer]

What was the problem with the original bolt holes that such drastic rework was required?

[@DiscoveringSkills]

the size of the bolts holes was over !

[@U.F.O.Technology]

If you scratch the car, then paint it to match the color of the scratch.

[@lamadanu]

Cars will still be running there for quite some time after the apocalypse.

[@dronivah5558]

Ещё походит)

[@favoritdmitry6786]

Tell me, what do you use as solder and flux?

[@DiscoveringSkills]

It’s our local product

[@favoritdmitry6786]

I don’t understand, I wanted to know the material of the solder and flux, sodium tetraborate flux?

[@highplainsdrifter8034]

The warranty on those engines. 10 minutes or until it makes it off the property

[@user-cs1cj2ro4v]

Whichever comes first

[@claywebb8199]

Where’s your KZbin channel, put a link up so you can show us all how it’s REALLY supposed to be done champ?

[@highplainsdrifter8034]

@@claywebb8199 hey hey hero! I don’t show off my stupidity! Rave oh! Someone well here ya holler

[@rickporras385]

How much does a job like this cost?

[@DiscoveringSkills]

30 dollar 💵

[@DiscoveringSkills]

Maximum

[@user-mv3lq2rs6x]

Мотор собранный в таких условиях долго не работает

[@user-lq9zo6xv2r]

долго и не надо,гарантия до ворот.в принципе как и во многих других мастерских

[@MISTERPRESIDENTELECT]

I think growing your own garden variety engine, is good for you. No chemicals, just charcoal...plus the barbecuing of engines brings the family together. ...ashes to ashes, hyundais to hyundais...

[@kevwills858]

This Almost seems like Insanity ? A 3 cylinder Engine that gets 100 hours ? of Attention ? Most loving Relationships do not get that even in One month 😄🖤

[@marcwolterdorf5859]

Bonjour combien gagner vous d argent par jour?

[@felipecampos7406]

I guess there is no such thing as deck height spec. !!

[@claywebb8199]

Where’s your KZbin channel, put a link up so you can show us all how it’s REALLY supposed to be done champ??

[@felipecampos7406]

You are absolutely right Clay

[@_tot_ruslan_]

Работа интересная, суетная. Но бесполезная. Из всех инструментов, был микрометр и тот не особо использовался... По сути, не долго ему поработать, потом обратно.

[@darknes7800]

Short term fix. It will crack again.

[@cameronlilly4814]

Who cares if it works. Lots of of operational engines have cracks.

[@darknes7800]

@@cameronlilly4814 For sure...No problem with cylinder wall cracks, external block cracks, crank journal cracks, cam bore cracks. Makes um run better !!!! LOL

[@cameronlilly4814]

@@darknes7800 Case 188 Diesel (deck cracks between cylinders) or GM 6.5 Diesel (cracks between valves, cracks in main-webs) -no shortage of operational cracked engines, or maybe Chrysler 5.2 magnums (cracks between valves being common)

[@servicetrucker5564]

@@cameronlilly4814That’s why when I did my 99 Dodge go through I didn’t take the heads off

[@reverendtfg6802]

*This must be an expensive job, they're using charcoal instead of cattle poo.* 💩💩💩

[@DiscoveringSkills]

Next time

[@darknes7800]

The boring and deck resurfacing is great......you can measure the imperfections with a Stanley tape measure. I have scrapped better equipment than being used in the video !!!!!!!!!!!! LOL

[@claywebb8199]

You really are a mug. Commenting over and over again. Show us all what you can do, go on 😂

[@saeedriaz7193]

Bhai jan ap ka number ky ha