Maytag Washer LF Low Flow Fault Diagnose & Repair

Maytag Washer LF Low Flow Fault Diagnose & Repair
Water Inlet Valve Failure & Replacement
Link to my Amazon Affiliate Shop: www.amazon.com...

[@BE_SUEQ]

Hello , we are a 68 and 70 year old couple who wants to thank you so much for taking the time to make this most helpful video.... we have had our Maytag Commercial Washer Model #MVWB765FWO for abt 4 years bought in 2017...we were having the very same problem as you were , so first thing we came to KZbin to see if anyone had any videos about our model washer to see if anyone else had the same problem and what they did. We found your video and though a different model # the washers were very similar...so we sat down and watched everything you did oh, gosh it was so easy to follow along ....our top was a little bit harder because the spring you were supposed to push on with the table knife was way far back....we finally got it though. we bought and downloaded the service manual ....and you demonstrating the getting it into service mode and out of the mode to test was so helpful.....so we ordered our part and it got here really fast...we watched the video again (we're old):) before we started , then started in today.... Oh man it's all fixed and washing a load as I type.... the hot water was what was broken on ours....whew ! We know if it had not been for this video, we could not have fixed it ourselves and it would have cost us a lot of money to call a repairman....then we would have had to wait till he had an opening ,while my dirty clothes pilled up ,till we had to go to a laundry mat...Then sometimes they have to order the part. Thank you for thinking to, and taking the time to put this video on here.... It Helped us so much . A Grandpa and Grandma in Kentucky

[@sandrarichardson2713]

Hi Susie---I am having problems with my washer filling extremely slowly. So, like you I started looking on youtube. My washer is exactly like yours I think---just a number or letter difference #MVWB865GW0. I am on the website where he found his manual and am trying to find the one specifically for my machine. You mentioned you purchased a service manual. Did you find the exact one for your machine or just use the one he purchased? Thanks a million for your response to this if you have time. Jesus bless.

[@jimtrammell8829]

Hey, thanks for posting. I tried your fix and it worked like a charm! Saved me an expensive visit from the Maytag guy.

[@mysurrender7]

Very clear and concise instructions made this fix a breeze. 1/2 hour tops, start to finish. I think the test procedure explained was the most useful as I didn’t want to remove the top to get the technician manual. Thanks again!

[@thecamerons-sy5ki]

Thank you Sir! Even though our washer is under warranty, repair was scheduled 8 days away. Previous experience tells me that even then they will probably have to order the part and additional days. Thank you for the helpful video, much appreciated!

[@KinkyKinkaid]

Thank you thank you!! When I popped the top control panel off (thank you for the butter knife trick) I noticed one of the solenoids was cracked. Low and behold after doing the test in your video it was the same one that was messed up! Ordered the part - got here in a day and now I have a working washer again! Thanks for taking the time to make this video!

[@LilianaM16]

Hi there! I just wanted to say thank you. My Maytag bravo XL was also giving me the the same LF error. At one point, I was considering throwing away my washer and purchasing a new one until I found your video. I went on Amazon and found the water inlet valve piece and I made sure that it was compatible with my Maytag. I ordered it and Hallelujah the piece came in the mail… I showed my brother your video and he was able to successfully install the device. As soon as he confirmed the piece was switched .. I tested the washer and it now works properly. Before the flow of cold water was very low and it would cause my washer to shut down. I just want to say thank you! Thank you! Thank you! Coming from a single mom of 3, I greatly appreciate you and my brother (since he completed the physical labor for free lol). God bless you.

[@VijayMurthy34]

This worked, thank you! The hardest part for me was finding the spring clip and getting the console off.

[@PatrickBalleux]

Thanks I followed your instructions. Mine was faulty on to cold intake and I did à quick test by blowing in the valves. Seems that the hot intake, you can easily blow air in it, but the cold side was totally blocked. I huffed and puffed until I got air flowing like on the hot side.

[@katephillips8441]

I am so grateful for your instructions, Mr. Rose, and for your link they took me right to the part I needed. You are providing a wonderful service for people. We are saving money and for people like my family who live in the country, it’s often hard to even get a repair person to come. Thanks so very much!

[@aaronsrose]

Thank you! Glad to help!

[@katephillips8441]

@@aaronsrose if you’ve fixed the matching dryer that blows but doesn’t heat, I’d be interested in that too!

[@EllenD333]

Omg thank YOU!!! I can't even tell you how grateful I am for your clear, easy, concise help! You're awesome! Thank you! *update! Ordered the exact part you linked, followed your instructions and I'm back in business, doing laundry for a family of 5. Yay! Whoa! Those clips were wicked tight! That way the only hard part

[@MrDewbe]

Just finished replacing it!💪🏽Thank you 🙏🏽 great video, made it easy! Paid $68 for the part from genuine replacement parts

[@tinareed4273]

Thank you so much for this video!!!! I had watched another video but they didn’t really show how to get those springs popped. Your video was perfect!! Thanks again!!

[@brianhacker7346]

Kudos and thanks so much, Aaron!. Everything was just as you showed, except my slightly different model would not go into test mode. I just decided to replace the inlet anyway and the problem was solved. My wife sends her thanks also 🙂

[@jtcamp49er]

Thank you soooooo much!!! This was the perfect instructional video to replace the Washer Water Inlet Valve!!!

[@aaronsrose]

Glad it helped!

[@billj4137]

Just an FYI, the tech manual is located in the machine itself and includes all the test modes and procedures. Mine was located on the inside of the upper left hand corner. Lift the lid and look inside.

[@rungratpruitt9213]

Thank you so much for your knowledge and very kind of you for being willing to share. . I am so grateful.🙏💝

[@jfinn31]

Just replaced this valve thanks to your video. Thanks a million!

[@gregtallant909]

Thanks for showing the special tool. Is there a way to get the screen out with out breaking it?

[@petermartini4526]

Thank you!!

[@mattwright3975]

Fantastic. Thank you.

[@bradvincet1848]

Thanks for the video. Have you tried switching the hot water valve wires to the oxy valve for a temporary fix? Prime is getting loose on 2 day delivery promises.

[@aaronsrose]

Thanks! I did consider that but the wires would not reach. I thought about adding a jumper, but figured it would be annoying. So I just used cold water wash for a while until the new valve arrived.

[@acerwin1]

My cold water main solenoid was the problem so I switched the wires because I don’t ever use the oxy or softener functions and it works just fine thanks for the video it helped

[@bradvincet1848]

I would like to know why a solenoid valve stops working. I checked the resistance on all 4 solenoids and they were all about 1k ohms. My water quality is excellent so that's not a problem. What is that other wire connection at the bottom of the manifold? I'll have to call tech support. I don't want this to be a recurring issue but there's probably nothing you can do about it. Foreign junk!

[@aaronsrose]

@@bradvincet1848 Best guess, is that the plunger that the coil moves when it is energized got something behind it or in the track it rides in. Thinking about it, I should've torn mine apart to see why it stuck. When mine fails again, I'll cut it open and see what happened. Thanks!

[@acerwin1]

I would like to know that as well since this is the second time it has happened to me. I thought about opening the first one but just got to busy with other things. I am going to order another another part to replace this one very soon. I will cut it open and respond with what my findings are.

[@barrykappel6118]

Great information video thank you

[@serafinarreguin7149]

Thanks a lot !!!

[@Ilovecrandall]

Can I please get a link to where you downloaded the repair tech manual? Thanks!

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@almaperez4677]

Do I have to put the washer in service mode or can I just replace it?

[@aaronsrose]

You can certainly just replace the part without going into service mode. Risk would be if that isn't actually the problem. It shouldn't hurt anything though. Thanks!

[@almaperez4677]

@@aaronsrose thank you

[@gsmboutiqueable]

You save me to spend thousands of dolar, thanks.

[@HarlanPenninger]

Appreciate you taking the time to make this video. Made the repair very simple and great explanations.

[@natalieschlegel8950]

I want to THANK-YOU!!! I’m a recently divorced mother of 17 yr old twins who put out a ton of dirty laundry…and because of this video…I fixed my own washing machine!!! Thank-You from the bottom of my heart!!!

[@kimberleerivera3334]

How Wonderful!

[@05mariana18]

Thank you for making this video, I fixed my washer following it.

[@acerwin1]

So if you switch the wires to trick the machine into using the oxy or softener solenoid it should get you back up and running without the oxy or softener functions. But you could have the opposite problem where the solenoid valve will not completely close; in that case your clothes will never get dry enough because it continues to leak water onto your clothes. I have had both problems with this washing machine. I will never buy another Maytag. Its sad, they used to be the best. Unfortunately all my appliances are Maytag and have issues with most of them.

[@cross3624]

Holy potatoes, this is the washer I just inherited with my new house and and this is EXACTLY what is happening with it. Because your instructions were so clear, I was able to test the washer without taking anything apart and it is indeed the #2 hot valve. Wish me luck!

[@KennisRussellMusic]

Sir, you are awesome. Thank you for making this. The exact issue I am having. Ordering the part now.

[@karenrodriguez5435]

Hi and thank you so much. I did this and sure enough my inlet Valve was bad. Not sure what happened cuz it washed fine once and then it now goes sensing,then to wash and back to sensing repeats and then done. No water coming in. Thanks karen

[@bradvincet1848]

Has your washer ever stopped in the middle of a wash cycle and shut off? That has happened to me a few times, especially after stopping it during operation to add a few items and to let it resume. Thanks

[@aaronsrose]

I've not seen that specifically except when it developed the LF fault and stopped. But I don't think it shut off when it did that. I don't add items too often, so if that is confusing the unit, I haven't tested that sequence often. Thanks!

[@davidpieper6940]

@@aaronsrose Aaron, I followed the video and replaced the valve and still no water ....could it be the circuit board? I hear a faint click, almost like a relay.. Great video and thx for your help

[@kendakline2384]

Found this while waiting for service people to return our calls - I ordered the part as suggested here and 30 minutes of labor - we are back in business!! thanks very much for your assistance on fixing our relatively new (5 years) Maytag washer for under $40.

[@chadkrop1]

Same story here!

[@Jodybell57]

Repairman just told me to get a new machine. The cost would be $450. 🤬

[@lindabennison4167]

I got this wSher from my sister .she passed. So not l am trying to use it .comes on.turns off.

[@jtsays429]

Just ordered from Amazon, I will let you know how it goes ☺ Mvwb834dc4 maytag commercial technology(MCT) bravis xl

[@taramaupin1334]

This video was SOOOOOO helpful! I followed it exactly and had ZERO issues repairing my washer. Saved me a huge service repair cost and I feel like I can conquer the world after fixing something myself! ☺️. I appreciate it so much!

[@aaronsrose]

Glad it helped. Thanks!

[@andrear7001]

Aaron, thank you for the information. My sweet in-laws are having problems with their washing machine and found this video. They have plenty of the "special tools"😂, but they're wondering exactly where they can get the manual you were referring to. Thank you!

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@marlamorgan2768]

Thank you so much for this video! This was so incredibly helpful. Husband fixed the washer and we only paid $35 for the part. Can't thank you enough!

[@rickycruz3891]

Where you buy the past?

[@lauraaragon58]

Love your video, so far I tested the machine and looks like it’s my cold water valve. Now I just need to order this replacement. Fingers crossed but hopeful.

[@lauraaragon58]

The part came in today and just installed it and it WORKED!!! Happy to do my laundry again😊 Thank you again.

[@godofsquire7866]

Yea the bored Maytag guy...not made like Mom and Dads Maytag..thanks for the posting this...had to work on the matching dryer too...

[@aaronsrose]

I've got the matching dryer as well. So far it's been fine, but I'm waiting for what breaks next. Thanks!

[@RuthiesLife]

Thank you so much!!! Everything worked and put problem was resolved. Only issue was we broke our paneling a bit when trying to pry the panel off where the spring was. Nothing some super glue can’t fix! 😀 thanks again!

[@Coraliaism]

Same! It’s all good. Doesn’t have to be pretty to wash clothes.

[@royshashibrock3990]

Great video! I was curious...I didn't see you check the water line filter plugs inside the water ports on the old valve. Were they known to be OK or did I miss your doing this?

[@aaronsrose]

Howdy! I did look at them when I removed the lines initially, but they were clear so I forgot to mention that in the video. Thanks!

[@jrkevinduddleston8072]

Sir, where can I purchase the Service Tech Sheet for a Maytag Bravos XL model # MVWB835DW1? Thank you James D.

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@sabrinakivler6205]

Thank you SO much for this step by step video. This was what was wrong with my Maytag washer as well. My husband isn’t much of a fix it man so with your help, I was able to do it myself!

[@melissameyer6726]

Do you have the link to the website where you got the booklet? After seeing all these people who needed to replace this part. I'm thinking twice about buying a MayTag.

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@petercaikauskas4759]

Thanks man, just put a new water valve unit in and it’s working great. Ours was only a month old, clearly they aren’t made well. Cheers!

[@debramatthews9180]

I just used this video to save lots of $$$ in repair bills. After getting the LF shut down in the middle of the wash cycle, I went looking for answers. The video is AWESOME. I installed the new water valve yesterday and this crappy washing machine is back in action for $30 from Amazon.

[@djdnewworld]

Hi, i went through the trouble shoot cycle. All water appears to come out on each cycle. But when actually start to wash no water comes out. Could it be valve?

[@aaronsrose]

Howdy! If the water dispenses when each of the four valves is cycled in the test, then the valve should be good.

[@Nektopoulo]

Just did this a few minutes ago, the 5 screws can also come off using a 1/4" nut driver

[@elliotdobner]

Wow thanks for this video, Just putting mine into service mode allowed to mess around with the different functions and I was able to get my washer running again

[@carrigan1412]

For those struggling to get the connectors off, I took a tiny flathead and put it on the top of the connector where it looks like a white "T" and tapped on the end of the screwdriver. Only thing that worked to get those off. Wiggling wasn't cutting it.

[@f4kle2431]

Thank you so much for taking the time to post this very helpful video. The way you explained are very clear, especially the steps how to pry the panel up. I could not fix the hot water problem without your video. Thank you again, Mr. Rose.

[@TheMakerDad]

Where did you find the service manual? My google-fu doesn't seem to work hahaha

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@lindabennison4167]

I love your video . My problem is F5 E2

[@PaulJamesDudley]

Thank you for your help. It worked for me

[@bradvincet1848]

I forgot to ask, how long have you owned it before it started malfunctioning? Mine is 3.5 years old. I knew these high efficiency washers wouldn't have the durability of the older washers. Thanks again for saving me time.

[@jrestrada15]

I purchased mine (Bravo XL top load washer) Feb. 2017

[@lewisgoodleaf1979]

THE BODHI 12345

[@davidpieper6940]

Help!!! I replaced the valve and it is still not filling!! I have 4 kids at home, this is an emergency as u can imagine. what should i check now?

[@aaronsrose]

If none of the valves are opening when tested, first thing I'd check is that the water hoses are actually not plugged up or off by removing the hoses and testing them. If only one of the water valves originally didn't work, I'd try reinstalling it to get the water flowing again. You can wash in either hot or cold instead of warm depending on the valve that works too avoid the error. If both the original and new valve set do not function at all when all four solenoids are tested and you're sure there is water flowing and that the wires are all connected it may be another issue.

[@marysepulveda4270]

I’m experiencing the same problem, but with the cold water flow. My Maytag is 3 year’s old. Where do I go to download the manual? I will tackle this tomorrow. I already checked the small filter. Plumber recommended I change the connector hose. He charges $140 just to come out. Hope I can fix it. Glad I found your video!

[@momonewe-tube2767]

Where can I get the manual. I keep looking and can't find it. Please help

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@garshO_o]

Thank you for making/uploading this video. For $40 bucks, I got my washer working again!

[@davidpieper6940]

Please someone , replaced valve and still not filling...hearing a very light click like its trying to open valve HELP!!!!!

[@mhh7226]

Thanks, fixed a Bravos XL with your videos help. It's crazy that, that washer is less than 2 years old and the hot valve went out. Then after doing about 3 loads on cold only, the cold valve also failed.

[@dhazelcamacho]

I can’t seem to get the top off with the knife like you did in the video? My washer doesn’t say bravo xl but it looks very similar. Does anyone know how I can lift it ? Model number : mvwb765fc1

[@aaronsrose]

Howdy! Looking at part #5 in this exploded view, it should be the same style clip. www.appliancepartspros.com/console-dispenser-parts-parts-for-maytag-mvwb765fc1.html So if you can get the knife aligned and far enough back to push it in a bit, you should be able to pop it up.

[@dhazelcamacho]

@@aaronsrose thank you! I was able to squeeze the clips underneath to open it!

[@sandramcpherson287]

Thank you for this video!! I just can't move my washer by myself! It's in a very tight place.

[@textex7475]

I'm guessing that part will work in mine. It's a very similar maytag I haven't pulled the face plate off yet but used your diagnostic test mode and found my hot aint workin to good. Should be good to go ahead and order the valve pack right?

[@schomesolutionsllc.7199]

Where did you get the info paper work in the video? Thank you, Mike C

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@morganredding7904]

Thank you so much for making this video. It came in handy this past week when ours showed the LF code. Thanks to you it was a easy fix and a cheap fix from Amazon.

[@markhowlett-c5e]

I need a manual also. Can you provide a link?? Thx!!

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@thegrovesedconnell]

My 10 year warranty model W11156983B is only 3 years old, thank goodness. I've had this fault go off periodically since day one and just couldn't be bothered to call but now it is happening almost weekly. Thanks for the video but I'm going to make some calls first, let's see how good the warranty is.

[@FrankG-l3c]

Thanks for the video!! I have a valve unit on order. The service mode information was VERY helpful! Oh, and the butter knife worked like a champ!!

[@asad6516]

would you please tell me where did you get the "Technician service manual" at, I would really like to get one. Loved the video by the way, thanks.

[@aaronsrose]

applianceassistant.com/shop/repair-manual/maytag-bravos-xl-washer-service-tech-sheet/ That's where I found it. Lots of ads on the site but it eventually worked. Thanks!

[@asad6516]

Got it, downloaded it, perfect. You are awesome, I do really appreciate your help, Thank you.

[@rubenj.garcia6828]

I checked my discharge pump it was found cleared what I did find is the hot water inlet screen was restricted with debris from metal rust I guess the hot water side for some reason rust more quickly than the cold, I cleared out and now it works fine, thank you for your well spoken instructions

[@kimberlyg.5487]

Great video explaining everything, seemed to fix the problem.....ordered the same part....you saved me a lot if money. Thanks so much!!!!

[@matthewq2854]

Amazing! Thank you, sir! For others, I had a hard time with the control panel, and almost broke it. Got access underneath by simply removing 2 screws. MUCH easier. kzbin.info/www/bejne/f6Gvd2NmbKeLo9k (starting at '38 sec mark).

[@mistybaize7316]

We were able to fix our washer thanks to you! Ordered the part on Amazon. Works great now! Thanks again!

[@roberteder2473]

This may help some. I was getting the LF error and was getting ready to replace the valve assembly when I found that this error can also be from the water level sensor is out of calibration. Get into " MAINTENANCE MODE " Pressing and holding the "Cycle Signal" button until a single beep is heard and the display displays "Pt" for zero calibration can recalibrate the water level sensor. (All clothing and water must be out of the washing machine's tub for proper calibration. Doing this fix my issue.

[@aaronsrose]

Excellent! Thank you!

[@rebeccadgeney]

I have the same washer as in video. But I don't see a Cycle Signal button. Which button are you referencing?

[@jibds2323]

Thank you so much for your great video. It helped me fix my problem with the same washer..

[@corycox24]

Thank you so much for taking the time to do this video. Ours was having the water come in so slow and giving us the "LF" error code. Thought I would try to fix it myself and came across your video. I found the replacement part on Amazon and was able to replace easily with the help of your video. Now water is flowing in as normal and no error code. THANKS AGAIN!

[@deborahvallin5061]

I remember that technician, too. Poor guy. With your help, I was able to fix it myself. Thank you so much!!!

[@peggyedwards6404]

I love the special tool. I went out and paid over $100 to purchase one. Knowing modern appliances I know I will get years of use. Also, great for spreading stuff on bread. Thanks!😆

[@stevenolden2195]

Great video, fixed my washer tonight thanks to this video!! You saved me hundreds of dollars thank you!!

[@sweetjoesus]

Like everyone else on here, thank you for this video! Back up and running in 20 minutes.

[@dennisgandy2924]

Thank you so much for this knowledge. I just ordered my second valve. The last valve only lasted 6 months and has failed again. Plumber removed sediment water filter when he put in the water softner. I think it is the sediment that is killing my valves. Thank you again, I am getting me one of those fancy tools to remove the top cover. Mine is cracked fro the the orginal removal.

[@garykrummert3681]

Thank you for posting this video and for your helpful explanation. I had the same problem w/my washing machine and I was able to repair it b/c of your excellent video. You saved me money and many other people!

[@lastboyscout8222]

thank you for making this video, especially the how to put it in diagnostic mode. could then confirm the cold water solenoid and get the replacement part ordered. got it installed and everything works. the butterknife tip worked well too.

[@killexzander7938]

I am super happy you made this video a week ago because my Maytag just crapped out on me today due to the cold water solenoid

[@dennisgarber]

Oh, I need your Amazon affiliate link to the special tool. I can't seem to find where I can get one of those weird flat tools. 😳

[@joshbadams2]

Oh man thank you so much for this. Saved me a lot of Time and money!! Perfect.

[@elizabethcarlson4124]

Thank you so much for this video!! We have been having issues with our washer for a year. And It’s only 3 years old. At first we could still wash loads on warm and hot but cold didn’t work. We did exactly what you said and found out the cold wasn’t working. We ordered the part on Amazon and got it in 2 days later. I couldn’t wait to try this out. I followed you with each step and we were able to fix it and it’s working better then ever!!! I can’t thank you enough sir! Thank you very much for this Alaina detailed video!

[@larsonhicks]

What a wonderfully helpful video. Thank you so much!

[@jankerwinfabie7764]

Life saver, just wanted to figure out how to take off the top, almost broke my cover

[@StuggleIsSurreal]

NOTE: Before removing the valve assembly: reseat the connectors before pulling the valve assembly and test. The connectors can become corroded in place and need to be reseated to break the corrosion and re-establish the connection.

[@dennisgarber]

You are saying to check connectors before replacing valve, or something else?

[@zipporah_prz8334]

Question: The connectors look rather delicate, how do you reseat them? I also recall he said it was very hard to remove the connectors (due to some corrosion) doesn’t successfully disengaging the connectors qualify as a reseating?

[@kaleadean3953]

@@zipporah_prz8334 I'm not an expert of even that knowledgeable but disengaged doesn't equal reseating unless the connectors are once again inserted after disengaging. I think.

[@bryanb400]

Great video. Thank you!! You have a radio personality voice!! 😂🇺🇸

[@ladyg6210]

Thank you for sharing this! Can you please share your affiliate link for the part that i need to order? Appreciate you!

[@tracymassucci7182]

I want to thank you for this!!! I just fixed my washer. Wooohooo. I feel so accomplished. You da man!!!

[@shelleymank755]

Thank you so much-your video was so simple and straight forward. We were able to do repair it ourselves and it saved us a ton of money! Washer works like a champ now 🎉