ABB REF615 Connection ,Testing & commissioning

Feeder protection and control REF615 IEC
Compact and versatile solution for utility and industrial power distribution systems
REF615 is a dedicated feeder protection and control relay for protection, control, measurement and supervision of overhead lines and cable feeders in utility and industrial power distribution systems, including radial, looped and meshed distribution networks, with or without distributed power generation.
Scope
Feeder protection
Product benefits
Extensive range of protection and control functionality, either with sensors or conventional instrument transformers
Ready-made standard configurations for fast and easy setup with tailoring capabilities
Withdrawable plug-in unit design for swift installation and testing
Large graphical display for showing customizable SLDs, accessible either locally or through an easy-to-use web-browser-based HMI
Extensive life-cycle services
Product features
Directional and non-directional overcurrent and earth-fault protection, voltage, frequency and power based protection and measurement functionality
Extensive earth-fault protection portfolio with unique multi-frequency admittance-based protection for higher sensitivity and selectivity
Optional advanced and fast fault location of short circuits and earth faults, arc protection and high-speed outputs
Supports IEC 61850 Editions 1 and 2, including HSR and PRP, GOOSE messaging and IEC 61850-9-2 LE for less wiring and supervised communication
IEEE 1588 V2 for high-accuracy time synchronization and maximum benefit of substation-level Ethernet communication
Supports Modbus, DNP3 and IEC 60870-5-103 communication protocol

[@dsbonde69]

Try to answer all questions. You have replied to very rare questions.

[@qshafim]

excellent Demo

[@atulnigam5176]

Hello sir its really helpful pls make one more focused video on configuration and parameters settings

[@alamzeb6342]

Nice effort, please show to CT and PT connections in more details and calculate the value for some feeder/motor on paper .

[@gmanikg]

Nice video

[@kanilkumar139]

Good information sir. Would you make a video on this very deeply, how much knowledge is required generally on this, we have to know on this, because nowadays so many areas going to this type of meter? Hope you can make one more best videos on this, Please cove these points in that 1. How to calculate over current on what base, and earth fault, 2. About TMS 3. Time delay reset time 4. How to activate programmable indications Such types are all regular requirements to be covered. 5.

[@yagnikpansuriya1267]

Pura video banaiye jisme connection, communication, programming, and parameters sab ku6 information mil jay ..

[@sanjayvadoliya8598]

👍

[@tashidawa7149]

Can this relay be used to protect both the LV & HV side of the incomer Transformer? especially for overcurrent protection

[@asimjan438]

Thanks for the video bro...just requesting you how much we set up the values for trip...like voltage, current

[@ramanpreetsinghturke8498]

sir please guide about under voltage blk value and over voltage blk value in vector surge setting in ABB relay REG 630 also please recommend what should be setting values for under voltage blk value & over voltage block value in relay.

[@ajeeyyadav5174]

Sir, Relay me Threshold voltage ki value kis base par rakha jata hai

[@muhammadsufyan8733]

Can you please show us in video from which option we can note down the incoming voltage and current and how to operate breaker from relay. Thanks.

[@naifbaamar5050]

Sir testing ke liye daily alag alag side per jana padta hai kya?

[@marmikdarji3906]

Do u have set values for 11 kv 5000 Mva x'mer?

[@nivendarsoo4575]

Do a video communicating with PCM600

[@kartikparekh987]

when i try to save settings it displays error message ' FAILED TO COMMIT ' can you pl help on how to resolve this issue.

[@ILAYARAJAraja]

Hi, I want to close breaker CBXCBR to close from the relay, if I try close from this section it's showing parameter in accessible, kindly share how I can make access

[@ashudhariwal5189]

Sir how to configure led earth fault trip and over current trip

[@chinmayapradhan5520]

Sir aap ke feeder ke requirement ke hisab se Yeh relay me kya kya setting ho sakta hey thoda video karke bataiye please sir

[@seftechbissau3424]

i want to know why the display of 615 is not coming

[@atifAli-fi2bv]

As relay software konsa use hota ha

[@RahulKumar-sw2hk]

Please sir tell me how to decide how much set value is used in any relay.

[@ahmedelshorpagy2863]

What is the value of In? Is it 5 ampere? Or is it any value I choose in setting?

[@rajnikantshingote6082]

In will be CT primary.

[@shridhargundkal6466]

I have a Master Trip alarm on my RF615. Start and Trip LED lights are showing stable ON. How do i reset it. I tried clearing it but it doesn't goes off.

[@rajnikantshingote6082]

When your Master trip operate, then go to main page on relay, it will show 86, and then press green key/ON key, your master trip will be reset.

[@gurpreetsinghee]

How Sync with laptop?

[@nitinmali5561]

I am having REF 611 relay .. it's trip circuit led is continuously showing red even after installing it in feeder..

[@learntech3122]

It will keep showing the red light untill you will make a diode circuit according to site parameters

[@shivkumar-jv2pe]

Sir how to i/p and o/p configuration And please send the wring diagram

[@saadahmed7639]

Ok

[@shaktisingh5614]

How to configure led pls explain

[@SRIKRISHNA19999]

Hi brother We are required to know how to communicate through the system. We want the Under voltage protection at 0 volts. Please help

[@mucoolsingh]

How to reset supervision led

[@jugendrapruseth5091]

ref 615 ki wiring diaram details explin ka video dalo sir ji

[@ILAYARAJAraja]

Menu-control-CBXCBR, this section not getting access to close BREAKER, I need access to close from this section, what I want to do to,

[@basantaraut2008]

RET 620 me non directional earth fault setting kase Kare ?

[@raisaniviews695]

Sir kindly ABB relay ki daigram ki pdf provide Kar dain setting ki calculation ki example koi solve Kar k is m feed Karna b Sikhaaa dain

[@satyarout9377]

Led kase configure karee

[@AnilKumar-ud5yn]

श्रीमान जी 🙏🙏 अगर 11kv feeder मै 150amp करंट बह रहा है. और really के mesaurment फोल्डर मै उसको डिस्प्ले मै 15 amp है प्लीज् सर बताये कहाँ सेटिंग distrub है 🙏🙏

[@Deepakkumar-hc8sn]

Led ko programme kaise karenge sir

[@vijayshankarprasad5743]

I learning relay setting any training center

[@iamgooch5382]

What power DC does it need to operate? 24v or 48v?

[@learntech3122]

24 to 110 vdc

[@ankurkumar6951]

Sir relay testing drawing se kaise kaise connection karege brief details m bataiye plz plz sir

[@baikunthalenka2776]

Sound

[@electricianguruji2.0]

MUJHE STARTING SE SIKHNA HAI ABB RELAY REF 615 KE BARE ME PLEASE REPLY

[@Falcon_Kashmir]

I dont think it functions on AC supply

[@stark5083]

Sir 6.6 kv feeder Mai overcurrent or earthfault ki normal kitni setting rkhe

[@rajnikantshingote6082]

Overcurrent setting will be depend on your load not on feeder KV rating, whether it is Motor load, transformer or any other.

[@harekrishna151]

In REF615 Over current start indication continue blinking what is problem

[@learntech3122]

It will blink untill you connect this relay to grid system & some diode arrangements will be required to acknowledge that light.you will find the connection diagrams in ABB drawing .

[@rajnikantshingote6082]

Check whether it is in Test mode or Normal mode.

[@sumanmanna6295]

Please give me a pfd of seeting value

[@saurabhghangare6422]

Want to know wiring details.... O/C trip, E/F trip , tcs , trip ckt unhealthy contacts where can be connected

[@learntech3122]

It depends on the model of relay..there are 5 models of this ref615 from A to f

[@user-yx5me8ur7n]

The salary for this job is about what

[@szcxicom]

How do we buy these?

[@learntech3122]

You can directly contact ABB sales representative in your area.

[@shivanandkatti1195]

I need power cards ret650 relay please reply me

[@soul8bit347]

Sir mene v kam kiya hai mujhe ar sikhna hai kya aap mujhe help kar sakte ho sikhne me

[@rayees-ul-islaamshah4628]

Plz help me for wiring diagram

[@RajuRaj-oi5zm]

Bro fault code 6 ka solution chhiye

[@user-ki1gt4su7p]

Sir what is R L on the keyboard

[@rajnikantshingote6082]

It's LR switch i.e.Local , Remote

[@qshafim]

Remote Local

[@waqasahmed3768]

is it a training institute?

[@learntech3122]

No , I was just configuring this Relay & though to make a video so every one can easily setup this Relay accordingly.

[@ragineesingh9189]

Trip Reset kaise kare

[@rajnikantshingote6082]

If your realy has in built 86 trip, then go to main page, where u will see "86" and then press green key, realy and indication will be reset. Otherwise go to programmable LED, indication LED and clear it, then scroll down for TRPTC1 master trip and reset it.

[@technicaltriloki20yearexpe75]

Full video Banai isko setting kaise karte hain kya kya dalna padta hai Sabhi batao Sharif video Banakar Bada hone do Parvah Nahin video

[@saikatjana6584]

Very Low Audio,Not Auduoble.

[@manoranjan4598]

Hindi plz

[@johnken6754]

Why don’t you make the videos in English, now for us who don’t understand Hindi even everyone is commenting in English

[@sachitnad]

I'm facing RTC error issue, contact number please