AC blowing HOT on one side on Honda and Acura

[@LaughingblueSu]

So much information. Thank you for the "behind the glove box" tour! It is good to see what we are getting into.

[@RBTheMechanic]

U welcome I have kore videos on this

[@patfung6880]

Great video. I really appreciate you for clarifying the mode motor vs the air mix (or blend door) motor. And yes, only Honda Accord with the dual climate control will have a main (left/driver) and a different right/passenger blend motor. The blend motor is harder to locate on a 2003-07 Accord dual climate and it is easy to get mistaken with the mode motor that you had mention.

[@RBTheMechanic]

Yup u know ur stuff!!!!

[@patfung6880]

@@RBTheMechanic Thanks…..But I cannot seem to get to the defective passenger blend door that is below the mode control actuator for my 2004 Accord EX-L with dual climate control. Would you have a video for that?

[@RBTheMechanic]

@@patfung6880 I have this video on the driver side bled door

[@patfung6880]

@@RBTheMechanic I saw your video and many other on the driver side blend door replacement. I had re & re the driver side about 1 year ago. I searched for hours and hours, but still cannot find one on the passenger side for an Accord wiry dual climate. I can barely see the blend door gear on the passenger side below the mode actuator, but cannot figure out how to get to it. Any tips?

[@RBTheMechanic]

@@patfung6880 u have dual? I will check tomorrow on my accord

[@tonywillingham8109]

You did not actually show where the right motor is located. You basically said, "rights right in there somewhere"

[@RBTheMechanic]

Yeah I have more videos these are old ones new ones I’m making the better and more detailed. I’m sorry

[@hondalover213]

it's rare to see a 4 cylinder EXL especially with navigation

[@RBTheMechanic]

Yeah sun roof and leather seats this one got

[@newandroidfan]

Mine is the same one, a 2007 Honda Accord with leather seats and navigation, on the window sticker that came with the car I think it also mentions it as EX w/ Navigation & Leather seats. I also have a sunroof.

[@elizabethkealy6866]

Do you have a video for mode door actuator?

[@RBTheMechanic]

Yes here’s is a link kzbin.info/www/bejne/j5fXiWB3hpx3hKcsi=b2X1ueh0MK6h7ewJ

[@marcoluns8864]

What happens if blend door motors both work when changing temp and has the freon ? But still on the drivers comes out warm and drivers cold ?

[@RBTheMechanic]

I have had issue with those well either ur ac compressor not building pressure or it have restriction in ac system possable cause the orifice tube is blocked also check ur cabin filter

[@rjcastillo3422]

I have the same issue with my mdx

[@donw3796]

Thanks for the video. I have this exact issue with hot air on passenger side and nice cold air on driver side. So which blendo motor do I need to change-- the one up top that you can see with the glove box removed, or the one on the bottom? THANKS!!!!!

[@RBTheMechanic]

U have to check before u change it see if it moved as u turn the temp up and down also cold be low Freon

[@moonmancastro]

half of this video is him describing how half the cars cold and it gradually gets hot towards the other side

[@RBTheMechanic]

It’s all about knowledge

[@Scott-un6qt]

I just bought a new ac relay, but noticed my passenger side is stuck on hot heat. Do you think it's the blend door on the passenger side?

[@RBTheMechanic]

I think so check that out first

[@Scott-un6qt]

@@RBTheMechanic any idea where it might be for the passenger Side?

[@RBTheMechanic]

@@Scott-un6qt u have single or dual control?

[@Scott-un6qt]

@@RBTheMechanic dual climate control

[@RBTheMechanic]

@@Scott-un6qt there’s one on each side located about same spot opposite of one another

[@troy4834]

Hey, i just got a new compressor installed on my 07 honda accord and aircon isnt as cool as it used to be.. Any idea why this would happen? One side seems cooler then the other, i just spent heaps of money and its not very cold. Could it be the compressor they put in or a under the dash problem like u have shown in the video?

[@RBTheMechanic]

Usully when that type of complaint comes to my shop and I have installed compressors and then it didn’t make very cold like my honda dose I redue the ac service meaning I recover and vaccum the system and recharge with correct amount of oil and r134 so if there too much oil or too much r134 or too little it would do somthing like that some times my machine messes up anyways. U might want to take it back to them and ask this question also how did they refill the system dud they vaccum and recharge. Hopefully they didn’t add with just cans that would off set. Let me know what happnes next

[@beikselect]

hi , thanks for this amazing video. by my civic 2017 is something i never saw before, not in KZbin or in google. As you said, from the right side there is cold air, and moving to the left side ( driver side) it blows hot air. So i went today to a garage to check the Freon and he told me that he was half empty, Ok i decided to check the actuator motors i noticed that they are fine, when i change it from hot to cold i see it moving in both sides, Driver an passenger. so any idea, please i am tired of all garages i am paying tons of money just cuz they are trying to solve it !!!!!

[@RBTheMechanic]

Just to let u know no one can every tell u it’s half empty u have to recover from system with ac machine then machine measures how much Freon came out of system they might simply looking at ur coolant level anyways. Try this put the car on put the ac on and then free the air on drivers side then push the gas peddle to 1500 to 1800 rpm. Take it easy don’t destroy the engine. And free the air if it gets cold even a bit in 4-10 seconds of holding RPM. Then it might need Freon service it might be low on Freon .. try this and let me know Also check ur cabin filter I had customer had super clogged filter that cause less air only vents on left side got good cold air

[@aaronboland1289]

Hey great video but I have a question I am working on a 2007 acura RDX It is Winter time the AC is working properly on both sides I have already changed the blender on the driver's side which was bad but it is now fixed however when the heat is turned up all the way on the passenger side it blows room temperature air at besthe 2nd vent on the passenger side gets slightly warmer the 3rd vent on the driver's side is hot the 4th event is the hottest I've checked all of the blind doors on the passenger side all seem to be working fine why am I not getting warm air coming on the passenger side? Any help would be much appreciated.

[@RBTheMechanic]

Check ur blend door motor again turn the door manually and see how that makes diffrence

[@kornyque8081]

What if its backwards ?I get hot air on the driver side and cool air on the passenger side, is it the same part to change or does it have one on the drivers side

[@RBTheMechanic]

Check operation of both blend door motor if u got dual if they work then reservice the system using ac machine could be low

[@alanchanthavisouk8557]

When installing the blend door actuator. Do I turned it on full blast first? N then remove it..

[@RBTheMechanic]

U can center it but usually I just throat it in and it adjust it self

[@felixalicea9326]

I have a 2005 Honda Accord 2.4 when I turn my heat from hot to cold on the driver side my blend door moves but when I turn it to hot on the passenger side the blend door doesn’t move can it be this?

[@RBTheMechanic]

That could be the issue u can move it manually take off the bolts and turn it softly and feel the air

[@robertgibbs1613]

Mine is cold on passenger side and warm on driver side. Same issue or something else?

[@RBTheMechanic]

U have dual control? Or single temp control?

[@saigeconnolly]

@@RBTheMechanic I have the same problem and I have dual control on an '02 accord

[@RBTheMechanic]

@@saigeconnolly check for both working blend door if they pass the checking test do ac pressure test and recharge if it seems off

[@GhostKing630]

Idk what’s going on I got a 2003 Honda Accord lx I just got 2 new relays for it and it’s still blowing hot

[@RBTheMechanic]

Ok. So try this. Open the hood. Have some one put the ac on and see if both fans on radiator come on. Let me know. If they do come on then check to see if ac compressor engages if it dosent. Then use test light and check power in to the one wire going to ac conpressor. If it got power u have bad ac compressor. Try all this

[@Mrintelligent100]

Hello I wanted to ask how many blend door actuators are on the passenger side of a 07 Honda Accord

[@RBTheMechanic]

If u got dual climate control then u have 1 if u don’t have dual then u have it on drivers side

[@brooklyn7941]

What about on the driver side ? Or the blend actuator is only located on the passenger side ?

[@RBTheMechanic]

@@brooklyn7941 if u have dual temp control then u got one on passenger side and one drivers side

[@brooklyn7941]

@@RBTheMechanic I check the one on the driver side the actuator is moving so does this mean maybe I low on Freon ?

[@RBTheMechanic]

@@brooklyn7941 yeah if ur doors are opening it could be low Freon

[@goofykiy8782]

Yes my 2005 Honda Accord is having this problem plus i just bought a new AC PART for my car last year for like $200

[@RBTheMechanic]

Which part did u buy? This issue is due to low Freon or if u have dual temp control then one side blend door motor is bad usually drivers sides goes

[@Jgct9686]

@@RBTheMechanicmy 04 is doing this. ,but I changed blend door motor & it’s operating right now but still not blowing cold on driver side… I checked for freon & it’s reading in the red zone

[@RBTheMechanic]

@@Jgct9686 reservice the systym other wise it could be bad ac compressor or somthing jammed

[@sestboogie]

What about if I put Freon and both sides where working the next day now the left side is warm and passenger side is cool .

[@RBTheMechanic]

sest boogie either u have leak and Freon went low or it’s in even Freon try vaccume and re add freon

[@daviderhahon]

You either have a bad expansion valve or a freon leak somewhere. Most likely, it's a freon leak. That's the most common cause. Probably bad valves or damaged condenser

[@brooklyn7941]

@@RBTheMechanic yeah this just happend my boy did a vaccum and I recharged on two bottles of Freon yesterday and today it’s doing that I’m like why but maybe we need to change the expansion valve and the evaporator

[@RBTheMechanic]

@@brooklyn7941 usully cans don’t work out well so u might want to check with machine how much comes out that’s what I usully do recover to see how much comes it because it could be a leak

[@DavidSmith-to3sr]

So if it’s cold on the passenger side an warm on the driver side but you can feel the change when you go from heat to an does that still mean you need to fix the blender also I was low on anti an used a lil water an it became cooler does that mean it needs charging with some new anti

[@RBTheMechanic]

No that’s success in determining ur blend door motors work so next step recharge the ac system use ac machine recover vaccum for 20 minutes the recharge correct amount

[@Tony_weis]

Hi i have a honda Accord 2003 lx, My problem is i only got heat on the right side, i put the heater on when is cold outside, and the driver side is not blowing hot air.. i check the actuator on the driver side and is working fine.. do You think i need to check the actuator you show in the video? The one in the right side ??

[@RBTheMechanic]

If u got dual control system then u need to check both for working operation

[@Tony_weis]

@@RBTheMechanic mine is not dual control

[@RBTheMechanic]

@@Tony_weis so there’s only 1 motor

[@mikeyeyes7]

I have one bad on my 14 Acura TL do I need to put the heat or AC all the way up before I remove it so the arm is fully open ?

[@RBTheMechanic]

mikey usually I put it in center it will calibrate it self some times u have to adjust once u install and feel the air

[@navardocartwright4702]

Same bro and I have same car

[@Aguez01]

Does this still apply to a single climate Honda Accord ?

[@RBTheMechanic]

The both sides will not change temp but if u experience once side cold and one side hot it might be low on Freon and is able to only cool off half of the evaporator core

[@Aguez01]

@@RBTheMechanic appreciate that we just put refrigerant in. Do you think it’s a leak or the expansion valve ?

[@RBTheMechanic]

@@Aguez01 it might be small slow leak give it a week or so if ur Lee working fine u don’t need to trace it down

[@MrSupernova111]

Mine gets stuck when the dual temp controls are different. When I set them at the same temp it starts working again. Is this a sign the motor is going out or something else?

[@RBTheMechanic]

It shouldn’t do that but wait till it fails completely so u can have know for sure

[@MrSupernova111]

@@RBTheMechanic . Its so weird. I also hear a clicking sound coming from the passenger side vents sometimes.

[@RBTheMechanic]

@@MrSupernova111 that might be the blend door motor next time it click try to put the air temp up and down if it stops the sound that conformed it’s the motor my honda dose that I haven’t changed it yet once it fails the temp will not change to cold or hot only will give what it was set at ...

[@MrSupernova111]

@@RBTheMechanic . I can look into that. Thank you so much for the information! I'll be checking out your other videos! You definitely deserve more subs!

[@daviderhahon]

After watching many of these videos, I got some silicone lube to lubricate all 4 blend actuators and their gears; at least the parts my fingers could get to. This is just to prevent them from getting stuck, so I wouldn't have to deal with the problem.

[@RBTheMechanic]

Yeah they usually give up on winter because cold weather freezes what ever type of lube is in there

[@ashtonmerrick2623]

a trick : watch series at Flixzone. Been using it for watching loads of movies recently.

[@tyrellbanks1111]

My high tube is cold and my low is hot

[@RBTheMechanic]

Prolly bad compressor

[@nighthawkj30A4]

on my 04 Accord EXV6 Sedan its cold on the passenger side and slightly warm on driver side. I removed the Drivers side Air mix control motor. And manually moved the levers and it never got cold. I even ran Onboard DTC codes and none where stored and lastly i see the motor moves them fully i think its low on refrigerant

[@Jgct9686]

U ever figured out what was wrong with it ?

[@nighthawkj30A4]

@@Jgct9686 yes i did

[@nighthawkj30A4]

@@Jgct9686 turns out the receiver/Dryer was clogged and actually had broke internally. Those little desiccant beads coming off. So that was causing a restriction in the system once i replaced that. And recharged the system gets to 42 Degrees on driver side vent.

[@Jgct9686]

@@nighthawkj30A4 what was it ? I’m having that problem right now , but I already replaced the blend door

[@nighthawkj30A4]

@@Jgct9686 it was not a door actuator. It was restriction in the system not allowing the refrigerant. To cycle though the system. It was so bad that it would cause the pressure relief valve on the compressor. To open releasing the refrigerant. Causing the system to be low.

[@Somair6469]

Try again you can get 100k hit if you are clear but you arn't.

[@JK-sh3do]

Whats so.simple. Lol

[@zackmcclintock8480]

So confused

[@zackmcclintock8480]

Crack kills

[@zackmcclintock8480]

Bro you are so confused

[@RBTheMechanic]

I’m sorry I will remake the video more clearly