How to use a RAMSET HammerShot FOR BEGINNERS concrete nail gun

$25 Amazon HammerShot: amzn.to/2xk6vEt
One with a silencer and trigger: amzn.to/2Oq1m52
I cover a lot more than just how to use it. Go to 6:25 to skip to the demo.
There are many options and brands but I don't use it that often so the $25 is just fine for me. If you live in Australia, you need to have this tool registered and a license plus training to use it. I'm curious what other countries regulations are.
22 cal loads: amzn.to/2MzwjSJ
Coated Pins: amzn.to/2xgpZus
This tool is used most often to attach wood to concrete or wood to steel but it can be used with other materials. There are many fasteners of various sizes and shapes. Check out the store display to see more. By the way, if you are curious as to the holding strength, good luck getting these nails out of concrete, it's possible but man it's not easy! These are permanent fasteners. Easier to grind it off than pull it out.
~~
For those who offer to buy me a drink, thank you! I have Venmo and CashApp.
CashApp: $AdamDIY
Venmo: AdamCash
/ adamdiy
/ adamdiy
/ adamdiy.me
/ adamdiyyoutube
Email & Mail:
/ adamdiy
~~
Disclaimer: This video is only for entertainment purposes. Any injury, damage, or loss that may result from improper use of tools, equipment, or from the information in this video is the sole responsibility of the viewer and is to be used at the discretion of the end-user/viewer and not AdamDIY and or Adam Hill. If you are uncertain about any step of the process or feel unsure about your skill level, seek a more authoritative source.

[@AdamDIY]

Yes, I know it's a long video, so go to 6:25 if you want to skip to the demo. In the first half, I cover safety, how to choose various loads, the difference in nails etc.

[@justwaa8346]

I am not scolding you for doing this put please do not use wd40 as a lubricant spray..it is alcohol based spray and will dry up and cause your tool to seize over time. It is meant to loosen seized tools/bolts and then apply a lubricant with a silicone base

[@1ozzyatx]

Great vid! What happens if you don't hold that lower piece of wood down the the Ramset or anything?

[@jacksonwheeler4731]

first youtube to actually tell the audience and be straight up, i like it💯

[@joshkroneberger479]

Are you using a 3" nail?

[@danielsfahmie8485]

How to oder..i am from malaysian

[@MagicGate814]

it's like playing with the snap caps when you were a kid, but doing something more productive as an adult

[@kozkoz7776]

Finally found tutorials that are simple. clear. easy. AND INFORMATIVE.

[@TravelingPrik]

One of the best, most informative, easy to follow, DIY videos I’ve seen. This video should double down as a how-to-make-a-DIY video

[@jamesandrew59]

Thanks. Brings back memories of my dad building a wall on the concrete patio. He blew a chunk of concrete off the corner. Getting prepared to build a pantry in the basement. I appreciate you going through the load colors.

[@thechrisepisodes812]

🤣🤣 it sounds dangerous lol

[@AndyTimm-pl7ob]

😊

[@AndyTimm-pl7ob]

😊😊😊😊😊😊😊😊

[@kmsti8677]

Now I understand where the word "powder" comes from. I was very confused at how the heck a tool so small drives through concrete. Amazing stuff.

[@phillmcgriff3226]

You were very helpful on the way you informed us on how to use this tool plus how you shared the difference in the powder shots, thanks so much 👍🏾

[@NickMango]

I have no idea why this has so many dislikes. Great video and appreciate the clarity. Thank you 👍

[@CesarBridgest]

Good work friend is a very useful tool when building partitions and separating environments Greetings from Chile

[@greg1becca2]

I use a rubber mallet it will set it off but won't damage the tool

[@ROBLOXKING99]

When I was a kid I used to steal those Ramsets .22 cal and put them in a steal pan on top of a fire in hopes to set them off for the noise xD

[@kunalkhanna985]

Excellent explanation of tool and parts used. I was able to comprehend how it works with ease. Thanks

[@danielaguilar3183]

Very descriptive, covered everything even prices. Very helpful 👌🏽

[@henryglarsson2635]

It shows the price at the start of the video

[@alanlee2121]

contact me

[@chrisfisichella6659]

That was really interesting to watch. I have walked by those things hundreds of times at the hardware store. Now, they are useful to me.

[@randymathews3348]

Already appreciate you using pt for your bottom plate 👍🏽👍🏽

[@djcichlid7746]

Nice and clear info adam, thanks. I have an old one as well that i used when i did my basement as well. And just wanted a quick refresher as i plan to help a pal out in the next few weeks

[@robertsneed7689]

Awesome demonstration of the Ramset tool 👌👍

[@shannond2707]

Thanks for the informative video :) I'm putting shelves in my concrete storage room and I'll need this tool. Your walkthrough was clear and answered all of my questions 👍

[@princelawrence1101]

Good job my friend. I learned pretty awesome today I never knew such a simple tool existed, so I am very happy. Thank you!

[@Theevilhawkmoth]

I watched two other videos on this tool and I appreciated this one the most. Thanks!

[@kubectlgetpo]

Is there a fully automatic version of this with a bump stock

[@CrimeDoesNotPay]

Yes, but with a background and cavity check if you live in CA.

[@phrostytwitch1603]

If it was fully auto, i don't believe you would need a bump stock, as the bump stock is meant to make a semi-auto weapon "automatic"?

[@themexicansensation2698]

Phrosty Twitch nope bump stocks don’t make semi automatic weapons automatic bc you still have to press the trigger every time you want to shoot it it basically just makes you shot very fast. If you only had to press the trigger once to shoot multiple then yes it would be automatic.

[@kubectlgetpo]

Good point that you don't need bump with an automatic. I was just throwing words around to sound cool

[@acesegura632]

U can modify then that’s illegal.

[@lonnieclemens8028]

Thank you for sharing this video. I wanted to learn about the Ramset.

[@KAHNER-zs7qs]

Thanks Adam! Very helpful video!

[@fredericmichel6287]

I know the hammershot we have a lot application concrete stone steel and so for you demo I prefer use screw and ankle is to long yes but most performant

[@Kriegerdammerung]

US creators of tools are some of the best in the world, mate!!!

[@WV-mx3dr]

Very useful video! Thanks for the power comparison

[@Deper38]

No need to be ashamed for the damaged tool mate, as long as it does it’s job and we know that some old tools are better then new ones :)

[@Joanzak52]

Thank you for your video. I used mine over ten years ago- though my carpenter used it a few years ago. I needed to review how to use it. Your video helped

[@fighters1000]

Genial esa gun hammer aca en Argentina es un lujo y jamás he visto un constructor de wood frame usar una de esas si la vi en un video de Canadá saludos muy buen video

[@tsetendorjee9040]

This is a very good TV show and we love it!

[@righteous1229]

Enlightening and Helpful!!!keep up the good work!!!

[@ProsenjitDC]

I'm your new subscriber. ....I like your video 👍

[@MrCaptainpope]

great video! Will this work on asphalt as well?

[@chadpendt2863]

Quick question. What do you think of the MAXtools high pressure nail gun? Would you make the switch if it meant saving time and money? 200-500psi. Can drive nails up to 5.5inches into steel or concrete. The full system with the high pressure gun and compressor is about $2k last i checked. The main benifit over a ramset is it is continuous. No need to reload on every single nail. No need to buy proprietary blanks and nails. It seems overall a better system. What are your thoughts?

[@rrezartbeqa83]

Hi Adam. I’m getting ready to build a shed kit. I have a concrete slab. The instructions are calling for sill plates to go directly onto the concrete slab - what would you suggest I use to attach the sill plates to concrete slab? Thanks in advance!

[@matthewjames1621]

Thanks for the video. Helpful. You should do another one that is 24 seconds for impatient people like me that want instant gratification when they are learning new tools

[@blangus]

really helpful video!!!!! Thanks!

[@paiperos]

thanks for sharing your knowledge

[@yalathary]

Very nice 👍 Your channel content is great

[@stanleyvo5198]

Thank you for explaining how to use ramset tool ....

[@euphoric52]

Thanks for the excellent video. All the demo videos for this tool show a vertical orientation for the shot. Does this work when you are trying to fasten a 2x4 to the side of a concrete patio?

[@monicavega3855]

Thanks to you we found out how to shoot BBS with this .....

[@josephmehri9359]

Thank you so much for sharing Great job

[@joe6699]

Thanks for ur help learned a lot

[@socialsaving]

When I was a kid my uncle used this he never told me about it, I wasn’t expecting the loud pop and almost shitted my pants 😂

[@kevinlong8072]

this tool is new to me , so thanks doing a demo.

[@inscrutianaII]

I don't recall anymore what caused my father to buy a model similar to this one in the mid-80's. Still works though it's been deep in a box for some decades and needs a good tear down. Even so, I used it earlier today! Maybe after I show it some love it will fully drive with the yellow loads. No matter what, this is so much cheaper and faster than using a hammer drill and tapcons. I really hate them.

[@johnle6536]

Out of curiosity, do you hammer in the rest of that nail or do you insert another “bullet” and have it a go one more time to get it to go all the way down?

[@juanecheverria9198]

Good demonstration...

[@marioparra78]

using the ramset gives me a rush , it scares me a little but i like it!

[@JerryCastaldo_NYC]

Great video. What about if you may need to remove wood from concrete later? I experimenting with various projects that may need to have the wood changed if it doesn't work for me.Will the gun allow for that? I know at least I could always unscrew the Tapcons, but was just curious.

[@joeluisramirez]

Thank you ,,,I was walking down the sidewalk next to a construction site and I stumbled across this tool,,,the site was closed, because it was a Sunday..I googled the part # and up popped your vid.

[@nemanjadraca4012]

I remember using this at a site and it kept splitting the cement lol I was like ooopppps

[@leopoldvicevice2464]

Good one, Some People HAVE THAT HABBIT OF silly remarks, thanks

[@sctpc]

Best use of them it will pop off 90% of locks in one shot. best break in tool out there

[@lordkrythic6246]

Not if you're trying to be quiet. A lot of people don't know that you can pick almost any lock, because they're all equally crappy designs.

[@alexlemus5596]

Thanks brother very helpful construction knowledge..👍

[@Koler2k]

This is the Lockpicking Lawyer and today, I have a concrete block

[@robertpark1212]

Hello Sir , This is an awesome tool for the construction industry. Can you let me know if there are any licences or documentation required for using or reselling this product?

[@2001BornAgain]

I got one of these just a couple of weeks ago, and I loaded the hannergun just like the other 20 times and did its thing. But when I pulled the stock back to release the shot, it was stuck in the chamber. How am I supposed to get it out? I can't seem to get a bite on it with anything. Thanks.

[@Xerroxify]

This reminds me of Greener"s Humane Horse Killer.

[@m1a2abrams52]

Humane dog killer

[@SteedDigital1]

So if I have existing walls on concrete but the base wood seems to just be regular fir 2x4's, how do I fix that is at all? I can't get under it to paint the wood or seal the concrete do I need to demo those walls or just let them rot?

[@lossan2]

Great Video.. Thank you.

[@sandsand5780]

Thank you sir for your teaching.

[@mikekaderly5907]

Any suggestion on how to use this tool to drive several nails into a concrete floor such that they stick out a specific distance (say 3/4") so the nail does not go flush to the floor?

[@juanpabloamaral9368]

Too Beautiful!

[@yanksguy23]

Thanks Adam. Just a word about lubricating the gun afterwards; WD-40 is not a lubricant (well, initially it is, but not really) but a solvent. When you spray it on anything it actually dissolves any lubricant that was there. Better to use Tri-Flow for lubrication.

[@benjaminrodriguez8778]

Good video Adam thanks

[@richk3325]

I have a 9 pound H&R 22 bolt action rifle that is a tack driver that this reminded me of...Target shooting is fun...

[@artaxerxes2363]

Was wondering what those nails were used for as I have a jar full of them at home.

[@AG.Floats]

"Any kind of penetrating oil" *sprays WD40* WD40 isn't a lubricant... It's a WATER DISPLACER. It dries up.

[@bigpicturethinking5620]

Andrew G here we go. It does displace water. It is a lubricant. It dries up as any other.

[@Treblaine]

He said a penetrating oil and WD40 is a penetrating oil. If it stops rust that can serve the same goal as lubrication as rust would increase resistance.

[@mayaandreaygrillomassar790]

Hmm. Well, it seems to be working for his tool; he mentions it has been working for him for years.

[@xenonram]

@@bigpicturethinking5620 People that say, "wd-40 isN'T A LubRiCaNT," are possibly the dumbest people on the earth. You've got to be really slow to not know it is a lubricant. I'll bet some KZbin idiot said, "WD is for water displacing, and it's not a lubricant."

[@DS-ss7vl]

@@xenonram Correct. It is a lubricant and water dispersant. It is not a penetrating oil though.

[@randombusboy1346]

Awesome video but hit it harder and it will drive if if it doesn’t drive I just throw another shot in there and whack the same pin again. Great maintenance advice!

[@newgravityfilms]

Great job! Thank you!

[@JaCass30]

I’m using 3” nails and they won’t go in all the way using the yellow 22s. Is my concrete too strong or do I just need 2 1/2”?

[@RICHUNCLEPENNYBAGS77]

According to the instructions you're not supposed to spray oil in there but hey what do I know

[@antispaghettigod1201]

What the instructions say I guess.

[@EujenSandu]

Also, WD40 is not a lube (though it has some oil inside) and is not intended to be used for the purposes of lubricating moving parts.

[@deconteesawyer5758]

@@EujenSandu ... and you sure as hell wouldn't use it to try and "lube" your guns.

[@mofaksalman9112]

Thank you and it was nice demonstration

[@philipmcrowsr7528]

interesting video, I forget what the purple level 6 loads are for, but they are a great tool.

[@trongtuyenvnbt]

it's amazing! but I cannot find any stores in Vietnam that sell this device.

[@davidhenderson3400]

I was helping to remodel an old house and the 150 year old wood was so hard we have to use one of those to nail to the old wood. I had never seen wood that hard before.

[@kripeshsasi]

Would it be able to drive in more thicker nails (diameter) into the concrete ?

[@JK-cn5fy]

Split pool noodle down side, incase ramset within (the silencer), and blast any deadbolt.

[@gregschilb4998]

i have been using 1 for years, my favorite deal is 1 time i was using in in a office building office some body heard it thought it was a gun shot and called the cops. i had to spend a hour telling the blank cop what a ramset is. but they are good tools

[@alexhernandez5755]

use hammer drill to drill pivots about 1/4 of nail length into concrete... then use nail gun/ or forse 3 to 4 nails into pivot hole with hammer using heavy blows wich is more resistent but more work.

[@abengtebaran5346]

Wow this the kind of tools that l need to drive nails thru woods till the cement thus awesome tools than.👍😯

[@jamescook5617]

thanks for actually showing how to load the bullet, a lot of videos don't.

[@shaikjamalahmed8]

Best weapon 👍

[@sylvestermariosu1667]

Thank for the education.

[@adnanaslam9138]

Amazing

[@glyco8307]

You are so elaborate... who can miss a detail?

[@noeguerrero8981]

I bought a dewalt ramset, and I can’t seem to depressed the gun. Am new to this...really new

[@user-bc3pc5gu2y]

No, it is just a very happy gun and positive gun.

[@nizartiger741]

Thanks buddy.

[@JonathanArmstrong514]

Up in Canada at Home Depot they charge more than double that price for the entry level model. $52.87

[@user-bc3pc5gu2y]

That is nothing compaired to prices of pneumatic tools, which probably arent close to as strong.

[@alred8497]

Nice good video thank u from Spain i subscribe

[@cleiamcf]

Thank vou, thank you, thank you!!!!!!! A thousand times thankssss!!!!! I'm brazillian, and my dad gifted my man, to this "toy"!!! Hahaha

[@holohulolo]

I've never seen this in my country. While it makes nailing a lot faster and easier, it also seems very expensive if you have to buy their nail, not to mention the cartridges which you also have to load after each nail. I'm assuming those nails are more expensive than regular but by how much? I see some other models that uses trigger, does the device substitute using hammer completely or is it used for specific jobs?

[@xenonram]

Did you watch the video? You can't use a hammer alone to sink nails into concrete. (Cut nails aren't used for this purpose) Also, it's not "very expensive" because the blanks and nails aren't proprietary.

[@ayahsadam9817]

Thanks for sharing👍👍

[@craiglkendall]

@AdamDIY any advice for setting a nail into red brick floors with one of these without shattering the brick? 2x4 bottom plate over red brick.

[@bastogne315]

How does the nail bind to the concrete?

[@modestilo6062]

Very nice video.. Thanks

[@mahdavimail]

Thanks for video

[@j.ridwan4059]

Yes, exciting.