I did what the video explains with a 2,7 kOhm and it works perfectly! really nice! it provides you the option of choosing between the 3 fly modes. I removed both potentiometer and placed the 3 position switches on that place. I recomend it!
@johnal45606 жыл бұрын
which switch did u buy can u give me the link thx
@81368213 жыл бұрын
I did the same. This means that you still have the 2 position switch as well and the new 3 position switch where the knob was.
@aussieaeromodeler3 жыл бұрын
Thanks , I have done this mod , it works perfectly , is it possible to use one of the other pots for an on off 2 position switch ? or can they only be used as in this mod ?
@JamesRader9 жыл бұрын
I have this very Radio on order, and I plan on doing this mod to make it fully compatible with my quads, Thank you for this!
@johnturner95619 жыл бұрын
Great video. Would it be possible to put one 3 way switch where you did and also put a 3 way in the knob pos. on the same side. thanks
@DIYTechRepairs9 жыл бұрын
Hi Sure it will work. Due to the limitations of this controller you then need to salvage the other turn pot as well. Ie you have to use both VRa and VRb Br Daniel
@1985kenworth16 жыл бұрын
i am going to try this to see if it works ..i am using my flysky for a dump trailer and hoping it will work .it seems to work fine on my spektrum dx7 with the 3 pos switch there but i would like to set up another truck to raise and lower the dump bed ..thanks for the video i will let you know how it works
@Brrraaapp9 жыл бұрын
Worked for me; great video. Now i can select flight modes on my quads!
@darkshadowsx59496 жыл бұрын
thanks i got it working. i had my model on variable pitch instead of fixed so vrb was controlled by throttle... all good now.
@TW398 ай бұрын
Does the resistors turn it into a 3 way switch
@grizzly1686 жыл бұрын
This video helps a lot.... can u put a second 3 position switch using the same methods?
@DIYTechRepairs6 жыл бұрын
It is a 3 position switch that I did use
@dwg88098 жыл бұрын
If anyone wants to get the job done quickly then just put the knob in the middle position and connect the three wires coming off of it to the switch so that the switch and the potentiometer is in parallel.Put some hot glue or something to fix the knob's position.I did it and works fine,didn't need to buy anything other than a three way switch.
@kenmcnaughton58827 жыл бұрын
Great It worked fine for me. Couldn't get the resistor method to work for some reason. much simpler too, just the switch required.
@Ajaxdima5 жыл бұрын
Hello, great video, i wanna do this mod to a Fs I6 for both VRa and VRb. If the potentiometers are 5K ohm, do you think its best to use two 5k ohm resistors instead of 2.7k to not overcharge the radio negative pole when switch Is in the middle position? Thank you if you will answer me
@coldfire30009 жыл бұрын
Thank you for this video, I used it to add a switch to my T6 and it works great!
@michaelmahoney6513 Жыл бұрын
What if I just want to add a 2 position on/off switch instead of vr?
@andy0x586 жыл бұрын
Hello! Thanks for video! I would to change place of the two switchers for hand
@venus_reborn2 жыл бұрын
Will it work on FS GT5 ? I used for winch on crawler rc.
@tonyglez1659 жыл бұрын
I have the same radio I will like to do the mod, can I still use the SWC if I place it in the pot hole since I will be disconnecting it? thanks for all your effort..(by the way can i do the same in the other side since the VR are very unusable? I will probably do what Jon Car suggested.
@joseluiszegarramelgar76258 жыл бұрын
Tengo una duda Es una resistencia de 2.7 KOhms???por qué no es comercial de 2.5 KOhms solo se consigue en el mercado de 2.2kohms o 2.7. Y el cable amarillo se anula??tiene alguna importancia la posición en la que queda el potenciometro?? Debe estar centrada o en algún extremo???
@darrellrogers57036 жыл бұрын
I bought a momentary 6 prong switch that fits in the fst6 fly sky my ?how can I wire up the switch I know I need to X 4 points leaving red and negative then I'm lost ?
@YoSneeze8 жыл бұрын
I want to try this out. Maybe one day I will. Thanks for the tutorial ;)
@edwincheng96177 жыл бұрын
Hi mate, for the resistors I cannot find the 1/8W with metal film resistors. Is there any different if I used the 1/8W with carbon filmed. I can only found the resistors either 1/4W with metal filmed or 1/8W with carbon filmed. Or what if I used metal film resistors with 1/4W, i.e., 0.25W? Thanks
@DIYTechRepairs7 жыл бұрын
It will work: goo.gl/Xd9BqE or goo.gl/T8m7mp
@antoniodagostino68388 жыл бұрын
Hello I would like to switch with 3 positions instead of Vra in this case the black wire should be connected?
@DIYTechRepairs8 жыл бұрын
Im not sure i follow what you want to do?
@antoniodagostino68388 жыл бұрын
sorry for my english....I would replace VRA and VRB with two 3-position switch.
@DIYTechRepairs8 жыл бұрын
Antonio D'Agostino ah ok. yeah it's possible. same procedure on other side. not sure of the colors though:)
@edwincheng96177 жыл бұрын
Hi mate, I have no knowledge in electronic. Is it safe for modifying it. Would the transmitter burned? Thanks for helping
@DIYTechRepairs7 жыл бұрын
Edwin Cheng as long as you do what was described here it will be fine and no harm caused :)
@johncarr1239 жыл бұрын
Why not just remove the pot and put the 3 way switch there and keep the other factory switch?? Also can we use 2.2K resistors?
@DIYTechRepairs9 жыл бұрын
You can ofcourse put the switch where the turn knob is. I didnt since i wanted mine in the right corner. In my case the best thing would be to move the 2way switch to the position where the knob was. 2,2k should work. Its not that critical. But i dont recomend to go lower. Happy modding!
@johncarr1239 жыл бұрын
daromeresperyd Thanks sir ordered the switch and resistors.
@copyandpastification8 жыл бұрын
nice video thank you, would you be able to add a telemetry module and make a video?
@MCsCreations7 жыл бұрын
WTF? I just bought one and was looking for information... And find you! Like, again! Kkkkkkkk
@kewalkks7 жыл бұрын
I have use this mod on flysky ct6b and this work very well thanks man👍🏻👌👌
@BiKersFury6 жыл бұрын
Techno Tech can u help me how to do it with ct6b .. I'm planing to use it with naza for mode switch
@MrGivmedew8 жыл бұрын
can I use a switch with more positions and just select between different levels of resistance to get more positions?
@DIYTechRepairs8 жыл бұрын
MrGivmedew yes you can
@cidzag9 жыл бұрын
Will it work on a FS I6? you did a great job, I will try this in my new radio FSI6 when it gets home!!
@Ajaxdima5 жыл бұрын
I've the i6, did this mod work well? Thank you
@lucianogreyck85909 жыл бұрын
I can use resistor 2,7k 1 / 4W Watt 0.25W ?
@kenmcnaughton58827 жыл бұрын
I did this mod and it worked in the display screen, but with the switch in the up or down position the screen went blank after a second or two, the middle position was ok, strange.
@eddy.saputra7 жыл бұрын
hi..nice vid....but could you share the vid without remove the the other switch....just replacing one VR to 3 pos Switch..?
@spencerclarke1528 жыл бұрын
hi great video. is this possible to do with the radiolink rc3s. and if so do u know the ristance I'll need?
@DIYTechRepairs8 жыл бұрын
as long as that controller have an analog input its possible! im afraid i never worked on those controllers.
@spencerclarke1528 жыл бұрын
it's a 4 channel controller got a push to no switch and a variable dial switch that can be set up for either channel 3 or 4.
@johnal45606 жыл бұрын
the link for the switch got 6 pin unlike yours can u give a link for one like yours thanks
@miguelmartibelmonte7 жыл бұрын
my channel 4 not found where is my problem, i need help :(
@guruji2437 жыл бұрын
Hi thanks for the vid. Does this mean that we can add more channels than 6?
@DIYTechRepairs7 жыл бұрын
guruji243 no. im just changing type of function on 1 channel.
@woowididit9 жыл бұрын
Hi there I followed the video but I'm only able to use two of the switches , no midpoint
@woowididit9 жыл бұрын
I got it to work, be very light with the solder and DO NOT BUY the blue 3 pin switches, they are car low in quality.
@DIYTechRepairs9 жыл бұрын
Adam Keely Nice to hear that you got it to work! It is always important to not overheat any component. A good hot iron is needed and solder it quickly. The blue as you say is very generic. There is blue ones that are aeroplane quality as well ;)
@woowididit9 жыл бұрын
Yeah your right, I tried a blue one but it just got warm and the switch stiffened up.
@johnal45606 жыл бұрын
which switch did u buy can u give me a link thx
@DIYTechRepairs9 жыл бұрын
Of some reason im not able to actually push "Reply..." Glez: You can use that position. The reason i didnt is because i want that button on the side instead. And yes you can remove the other VR as well. Im planning on another video and create a 4way rotary switch and also perhaps doing so both the switch and the VR knob is actually use able
@woowididit9 жыл бұрын
Is it possible to add on a new module instead of the old one ?
@DIYTechRepairs9 жыл бұрын
Adam Keely What do you mean with new module?
@woowididit9 жыл бұрын
Like the frysky module?
@DIYTechRepairs9 жыл бұрын
Adam Keely It might be possible. The module itself is put there in such manner that it might work but i havent done it and will not try either. The reason i wont try is because of the bad quality of the transmiter itsell and would therefore buy a better one instead that already have support for it :)
@woowididit9 жыл бұрын
Yeah I see what your saying, I guess I'll have to invest in a turnigy 9xr
@woowididit9 жыл бұрын
Why does for some reason it flickers up and down , so on the naza flight controller it goes on failsafe on its own
@AJG02able8 жыл бұрын
+Adam Keely ::::: Put a new switch in its place ... you may have over heated the switch while soldering. That is what is causing the flickering.
@davidb45578 жыл бұрын
Will it work as a flap switch. 0-50%-100%.
@DIYTechRepairs8 жыл бұрын
yes it will.
@davidb45578 жыл бұрын
Thanks.
@wilsonoliveira21684 жыл бұрын
Poderia passar as cores do resistor?
@alessandroinn4697 жыл бұрын
Hi! It's works also for flysky FS-I6 or Eachine I6 radios? Thanks 😉
@DIYTechRepairs7 жыл бұрын
If they have the same type of layout: yes it does. Its just a matter of taking one of the variable knobs and turning it into a 3way switch
@alessandroinn4697 жыл бұрын
I don' t know... I think that the 2 way switches has only 2 wires connected instead 3...
@DIYTechRepairs7 жыл бұрын
alessandro inn yes. 2 way is 2 wires and 3 way is 3.
@alessandroinn4697 жыл бұрын
And so, where can I take the third cable?
@alessandroinn4697 жыл бұрын
And so, where can I take the third cable? I don' t understand
@Gho5tface7 жыл бұрын
Btw for anyone wondering (even if it might be obvious), works fine with 10k resistors too ( I guess it doesn't matter as long as its greater or equal to 2.7k)
@DIYTechRepairs7 жыл бұрын
Gho5tface correct.
@Gho5tface7 жыл бұрын
Btw. great vid - just completed the mod and replaced both knobs with 3 way switches :D
@themusichallacademy27874 жыл бұрын
THANK YOU 🥰
@enmadam96249 жыл бұрын
Is your switch 3 pin or 6pin ?
@DIYTechRepairs9 жыл бұрын
Its a 3pin. You can ofcourse use a 6pin as well.
@johnal45606 жыл бұрын
how do u use 6 pin i mean how u connect them thanks
@farrda18 жыл бұрын
Good job
@camshaftshaft27119 жыл бұрын
Worked on mine thanks again 👍
@ollyk225 жыл бұрын
Struggling to find a nice 3 way toggle switch that is similar to the original. Anyone found anything?
@enmadam96249 жыл бұрын
I followed it video and now i have a 3position switch
@camshaftshaft27119 жыл бұрын
thanks doing it tomorrow :)
@danielpeters69068 жыл бұрын
would this work on the fs i6
@DIYTechRepairs8 жыл бұрын
+daniel peters It will work on every transmitter that has an variable know that you would like to sacrifice.
@MrBlakepare9 жыл бұрын
TQ bro,Keep it up
@andreyglyan7 жыл бұрын
Cool!
@AbdulMajeed-px7ym5 жыл бұрын
V good bro 😚😚😚😚
@БорисПопов-ш2н8 жыл бұрын
спасибо все получилось
@mustafasuzen228 жыл бұрын
You can make this mod without disabling the knob. Keep the knob where it is. Instead of adding resistors to knob cable make Y connection with 2 resistors one of them 2.7K other one 4.7K. Connect them each outer end of the 3 way switch. Disable 2 way switch. Connect live wire to middle connection of 3 way switch and connect the other wire to middle of 2 resistors. In this way; you have one 2 way switch, 2 knob (working if you choose), and one 3 way switch without loosing the knobs function. Like this: www.dropbox.com/s/ibb09w0fnpass5y/20151223_010642.jpg?dl=0
@OAW_SE8 жыл бұрын
+Mustafa Süzen I will try this as soon as I have received the 3-way switch.
@БорисПопов-ш2н8 жыл бұрын
+Mustafa Süzen tell me what wires you have attached ?
@matrixdrones8 жыл бұрын
+ Mustafa Süzen tenho um radio desse e no lugar do potenciometro coloquei um chave de 3 posições com resistores e deu certo uso no drone naza m lite com gps. att e failsafe
@MrGivmedew8 жыл бұрын
Mustafa Süzen can you make a detailed tutorial? As this guy was doing this I was thinking to myself why not have a 3 way switch that is lowest on 1 position leaves the potentiometer alone in the middle position and highest in the 3rd position but I like your idea better. No point in loosing any functions when this controller can actually do 10 channels and SBUS.
@matrixdrones8 жыл бұрын
You buy several resistors for example 2k 3.3k 10k and several same 20 and buy a 3 position switch. Take out the potentiometer and put the resistors and the dji program open on the pc so you can see the correct positions that you want to do that works. If you want to get my whatsapp +55.84.98892 1482