ADIRONDACK CHAIR with Free pdf Plans!

  Рет қаралды 62,951

TSW Woodworking

TSW Woodworking

Күн бұрын

Пікірлер
@erkansavasci
@erkansavasci 9 ай бұрын
Great video, but it's especially awesome that you shared the plans. I have now solved all the missing parts by reading all the comments. Regards from Turkey and thank you for sharing ...
@tswwoodworking
@tswwoodworking 9 ай бұрын
Glad it was helpful. Yes, I should have made it clearer that templates were for curved parts and square parts were listed in description. And, I’m always amazed at how videos connect with people across the globe! Thanks
@jimmyturner5589
@jimmyturner5589 Жыл бұрын
New subscriber from Missouri, this brings back memories of my dad when he used to make these to sell to make some extra money, and thanks for the templates.
@tswwoodworking
@tswwoodworking Жыл бұрын
Thanks for subscribing! I have good memories too. All the skills my dad shared with me, and I still use some of his tools😁
@Neenkofi
@Neenkofi 5 ай бұрын
New subscriber from South Africa. This is going to be my first project. This is the most wonderful and thorough video I have seen yet. Love that you explain everything so clearly. Thank you so much.
@tswwoodworking
@tswwoodworking 5 ай бұрын
Glad you like it. If you make the templates, you can always make two :) Personally, I like the folding one too since I can store it away. kzbin.info/www/bejne/fnzam5WVet1rgcU
@amoret6108
@amoret6108 4 ай бұрын
Made 2 for our daughter she loves them, thanks for making the plans available. One modification I made was the last seat slat that goes against the back slats, I made a curved section that matched the curve of the lower back back slats filling in the gap.
@tswwoodworking
@tswwoodworking 4 ай бұрын
Glad it was useful. Changing things is good. Always room for improvement. I’d change a couple things with my workbench if i ever made another one.
@garyperrin8172
@garyperrin8172 10 ай бұрын
thanks for the plans i am from Nova Scotia Canada
@tswwoodworking
@tswwoodworking 9 ай бұрын
Glad you liked them. We loved Cape Breton and Digby.
@islandindependencel.l.c.3484
@islandindependencel.l.c.3484 Ай бұрын
Thanks Brah, my students at Lahainaluna high school are going to make this .!! Aloha from Maui Make shop class great again
@tswwoodworking
@tswwoodworking Ай бұрын
That is awesome!😎
@tswwoodworking
@tswwoodworking Ай бұрын
Shop class might like to make the folding version as well that there are free plans too. Easier to store or transport
@danielbiyatanov9892
@danielbiyatanov9892 Жыл бұрын
Thank you from Belarus, its really gratful of you!
@tswwoodworking
@tswwoodworking Жыл бұрын
Thanks the comment and for watching! Check out the other videos on my channel 😊
@CameronMcInroy
@CameronMcInroy 10 ай бұрын
I happy that I could get the templates but I had a problem downloading them onto my computer.
@tswwoodworking
@tswwoodworking 10 ай бұрын
drive.google.com/file/d/1C8A1L3wLysGF9qkUGQIfO9NlyfET1aY2/view?usp=sharing It’s just on google docs link. It says anyone with link should have access. Hope it works for you.
@samuelpuckett7954
@samuelpuckett7954 Жыл бұрын
It may be because I was on an iPad but never saw the plan you offered. If there’s a price let me know. Loved your chair. Thanks!
@tswwoodworking
@tswwoodworking Жыл бұрын
There’s a free link in the description for a pdf of all the curved pieces. All the square pieces sizes are just listed in description area. Hope that helps, let me know how the chair comes out!
@alexreid4131
@alexreid4131 Жыл бұрын
Thank you for all of your hard work on this and for providing plans. I subscribed to you immediately. Looking forward to following your future builds and content.
@tswwoodworking
@tswwoodworking Жыл бұрын
Thank you. I appreciate that. Just make sure your printer is set to 100%, some printers auto adjust and then grid is not 1 x 1 inch. Enjoy!
@alexreid4131
@alexreid4131 Жыл бұрын
@@tswwoodworking Thanks for the tip!
@estevezcarlos67
@estevezcarlos67 8 ай бұрын
Thank you for the template Very kind of you to not charge for it I’m from Miami, FL
@tswwoodworking
@tswwoodworking 8 ай бұрын
No problem. Good luck.
@tswwoodworking
@tswwoodworking 8 ай бұрын
There are free templates for a folding Adirondack Chair on that video as well that I like since you can store it away.
@titusoneten6456
@titusoneten6456 4 ай бұрын
Great video! I am going to try making one this weekend!
@tswwoodworking
@tswwoodworking 4 ай бұрын
That’s great. Good luck
@CaseyIverson10
@CaseyIverson10 10 ай бұрын
what stain and sealant would you recommend if these are left out in the elements all the time? Also what would you change to make the chair 2-4" taller? just the front legs longer and change the angle of the back, or would that whole piece need to be longer as well? Thanks for taking the time to make the video!
@tswwoodworking
@tswwoodworking 10 ай бұрын
Depends on type of wood used. I made these out of white oak which exterior doors are sometimes made from. Could use whatever stain you like, but I then spray with Waterlox (modified Tung oil). If you make chairs out of cedar or something that doesn’t take stain well, I just coat with the Waterlox and let wood change to eventual color which can be nice. I’m not a fan of polyurethane. Seems to flake over time. Hope that helps. Oh, and I have made a raised one, but was just modified design but don’t have plans for it. Good luck!
@telosfd
@telosfd Жыл бұрын
I like it! Why no glue during assembly?
@tswwoodworking
@tswwoodworking Жыл бұрын
I used glue. I don’t think I said anything during video, but I have a little bottle. You can see it at 8:57, and I’m sure I used it during back slat attachment. Thanks for the comment. Hope you make one!
@amirmansoor8208
@amirmansoor8208 4 ай бұрын
Thanks for the plans. Can we keep back vertical support, front / back cross stretchers all 3.5" wide. I have SPF wood 3/4" x 3.5". Thanks
@tswwoodworking
@tswwoodworking 3 ай бұрын
Yes, depending on what I have available, I often modify even my own plans as I go along.
@robertt9991
@robertt9991 Жыл бұрын
Great vid, very informative and easy-to-follow.
@tswwoodworking
@tswwoodworking Жыл бұрын
Glad you enjoyed it! Thanks for watching!
@johnyork-qr5dc
@johnyork-qr5dc Жыл бұрын
Hi Mr. TSW, I sure appreciate your time that you invested in making these templates. I recently came accross your channel. I want to attempt to make a pair of these adirondack chairs. I believe I that I can by using your template and following along with your video as I begin. Would you happen to have a shooping list for the materials? I was thinking of using pressure treated material. What are your thoughts on using pressure treated?
@tswwoodworking
@tswwoodworking Жыл бұрын
Glad you enjoyed it! I used approx 5 pieces of 1x6x12. The hardware is listed with the plans. I used stainless steel hardware. As far as PT lumber, if that is what you have available, then that would work. I just don’t like using that for anything that touches the skin. My personal preference. Good luck with the project! Let us know how it turns out.
@johnyork-qr5dc
@johnyork-qr5dc Жыл бұрын
@@tswwoodworking will do. What type of wood was the 1x12?
@tswwoodworking
@tswwoodworking 11 ай бұрын
I used white oak for the Adirondack Chair video and cedar for the Folding Adirondack Chair video. Use whatever you have available, even pine boards. It won’t be as weather resistant, but cheaper to practice on.
@vizzini2010
@vizzini2010 Ай бұрын
love this plan, going to make one on my next day off, thanks for putting it up with free plans and templates I will probably make it with pine how many and how long lengths do you think it would take to do everything except for the seat slats and back rest? I am think i can just rip down 2 x 4's for them
@tswwoodworking
@tswwoodworking Ай бұрын
I’ll have to do some calculations. You could rip 2x4s for the seat slats. Have to resaw them to make the back slats.
@tswwoodworking
@tswwoodworking Ай бұрын
If you are going to plane down “2 by” material, arms will need about 2x8 x 6’ and legs (long and front) will take about 2x6 x 10’ of material. If you wanted to do rest with planed down 2x4 material, you can. I’d think of cost and your time too. Might be worth it to buy material already planed to thickness. But sometimes repurposed, free or discounted material, can’t be passed up. Good luck!
@vizzini2010
@vizzini2010 Ай бұрын
@@tswwoodworking thank you very much
@charliewelch4162
@charliewelch4162 6 ай бұрын
Thank you for sharing the plans, what is the gap between the seat slats and the back rest, Thank you
@tswwoodworking
@tswwoodworking 6 ай бұрын
I’ll have to check. I just started from front seat slat, working towards the back and used drill bit as spacer for seat slats to get a nice consistent look.
@charliewelch4162
@charliewelch4162 6 ай бұрын
@@tswwoodworking Thank you
@tswwoodworking
@tswwoodworking 6 ай бұрын
I checked and I used a 3/16” drill bit as spacer between seat slats. This leaves about 3/8” between last seat slat and back rest vertical pieces. Hope that helps
@charliewelch4162
@charliewelch4162 6 ай бұрын
@@tswwoodworking Thank you so much, you do such a great job building!
@tswwoodworking
@tswwoodworking Ай бұрын
Thank you! I appreciate that
@lucdominique3713
@lucdominique3713 Жыл бұрын
Bonjour, Je ne parle pas l'anglais, j'utilise un traducteur. J'ai beaucoup aimé votre chaise. J'ai imprimé les plans et je vais essayer d'en fabriquer une. Merci de nous faire partager votre savoir. Luc de France Good morning, I don't speak English, I use a translator. I really liked your chair. I printed the plans and am going to try to make one. Thank you for sharing your knowledge with us. Luc from France
@tswwoodworking
@tswwoodworking Жыл бұрын
Merci Luc. Je suis avec toi, Bonnie chance avec ton projet 👍
@DonLewis-gb7lb
@DonLewis-gb7lb 7 ай бұрын
This is the chair I made back in 2011. The template s for this particular chair was some how destroyed. I was hoping that you can send off for the free PDF sheets and I can transfer the measurements on to a 1/4 inch thick of wooden material. All the measurements is accurate that you come across as you read. If some is fat..or just got a big fat ass,.. I just need to make the seat a little wider.
@tswwoodworking
@tswwoodworking 7 ай бұрын
The link for the pdf templates is in the video description. You can adjust the width to suit your needs. Good luck!
@keithadams1538
@keithadams1538 Жыл бұрын
I had to use another browser to get the plans. When you did the temp spacers you said one at 20 the other 18 1/2 but surely they should both be 18 1/2 because the seat slats are 20. I'm most way through cutting the shapes unfortunately I do not have a bandsaw so a jig saw had to suffice. My timber is 1 1/4 thick oak so will adjust measurements accordingly. Anyway thank you so much for the inspiration to do this project
@tswwoodworking
@tswwoodworking Жыл бұрын
That will be one stout chair. I’m sure it’ll be nice!
@keithadams1538
@keithadams1538 Жыл бұрын
It is completed and beautiful better than expected and very comfortable. Now the long wait for Summer. Thank you@@tswwoodworking
@tswwoodworking
@tswwoodworking 11 ай бұрын
You are very welcome! I’m sure you’ll get a sense of satisfaction every time you use it. I know I do. Cheers.
@aguinaldodossantos
@aguinaldodossantos 4 ай бұрын
new subscriber from Curitiba, Brazil
@tswwoodworking
@tswwoodworking 4 ай бұрын
Obrigado!
@joseedinaldo3672
@joseedinaldo3672 Жыл бұрын
Queria muito fazer uma cadeira igual a essa. Legal parece ser bem confortável, muito obrigado por fornecer os planos em PDF. Saudações aqui do Brasil.
@tswwoodworking
@tswwoodworking Жыл бұрын
Good luck with the build. Let me know how it goes.
@fabfafa
@fabfafa Жыл бұрын
Great video. Thank you from France
@tswwoodworking
@tswwoodworking Жыл бұрын
Merci. Love your country, especially Nuit Saint Georges. Great wine!
@arnulfoacevedosoto7956
@arnulfoacevedosoto7956 Жыл бұрын
Espectacular video gracias por compartir las plantillas
@tswwoodworking
@tswwoodworking Жыл бұрын
De nada. I’m glad you liked it. I’m drawing up a Folding Adirondack chair to post as well.
@johnbush4412
@johnbush4412 Жыл бұрын
So what degree is the tapering jig for the back slats?
@tswwoodworking
@tswwoodworking Жыл бұрын
John, If you are asking the vertical back support, it is 30 degrees. If you are asking the curve for the back slats, I made middle one 32" long, installed all of them, then marked 29 1/2" at outside edge on the most outside slat. Then, I drew gentle curve between those, and cut to that curve on the bandsaw. Hope that helps. Let me know.
@arvidnorberg2879
@arvidnorberg2879 Жыл бұрын
Thanks for great video! Just to be sure, did you use 3/4” for all parts? Many thanks /Arvid
@tswwoodworking
@tswwoodworking Жыл бұрын
Yes, it was all 3/4”. You could vary thickness and make design adjustments, but keeping it consistent was one of my goals.
@MidGAOutdoor
@MidGAOutdoor 10 ай бұрын
would you mind sharing the length of the main leg and what the angle is where it sits on the ground? also how far is the bottom of the main support from the bottom end of the front leg? thanks so much.
@tswwoodworking
@tswwoodworking 10 ай бұрын
Main leg is 38.5” and the angle is 72 degrees. That front leg meet the long leg 7.25” from floor in its front. If you print it the templates from link in video description, I think that may help to visualize. Hope that helps.
@nicklee8103
@nicklee8103 2 ай бұрын
So what is the width of the backslats? I see they’re 32” in length with some tapering at the top to round them, but see no info about WIDTH and see your comment about misspeaking in regard to the 2.5” inch to 2” taper. Your front spacer length is also inaccurate since it goes in between the 2 side boards while the seat slats go on top of them, doesn’t make it 20” anymore. Any help would be appreciated. Hard video to follow
@tswwoodworking
@tswwoodworking 2 ай бұрын
All pieces not included in templates are listed in video description In regards to your question about front cross stretcher. It is 20” long which is same as seat slats. Back stretcher is shorter at 18.5” which may vary depending on your stock thickness. Copied from description: List of other pieces (2) Front legs. 20 x 5 1/2" (2) Back Vertical supports 25 1/4 x 3" (1) Front cross stretcher 20 x 4" (1) Back cross stretcher 18 1/2 x 4" (14) Seat slats 20 x 1 1/2" (7) Back Slats 32" long (2 1/2 tapered to 2") Good luck
@JohnYerina
@JohnYerina 4 ай бұрын
How can the front stretcher be 20" and the seat slats the same length. in order to make them fit the seat slats will have to be 21 1/2"
@tswwoodworking
@tswwoodworking 4 ай бұрын
It is same length as seat slats. It is attached between front legs and long back legs rest on top of it.
@daveellis7117
@daveellis7117 Жыл бұрын
Oi Parabéns pelo lindo trabalho! Baixei as medidas em pdf mas faltam as duas madeiras de frente ou seja! Os pés da frente
@tswwoodworking
@tswwoodworking Жыл бұрын
Hey Dave, the pdf has the dimension templates for all the curved pieces. The parts which are square cuts (which includes the vertical front legs) are just listed in the video description section. Hope that helps!
@benkennedy7662
@benkennedy7662 6 ай бұрын
What angle did you use at the top of the back vertical supports? Is the 25 1/4" dimension the long or short dimension?
@tswwoodworking
@tswwoodworking 6 ай бұрын
That angle is 30 degrees with the 25 1/4” being the long edge. Hope that helps
@SteveHoldaway
@SteveHoldaway Жыл бұрын
Thanks for the video. I've cut all the parts, but found the lower back support is about an inch and a half shorter than the slats. Am I missing something?
@tswwoodworking
@tswwoodworking Жыл бұрын
The lower back support should be 20” long, and the upper back support should be 22” long. The previous reply was about the Folding Adirondack Char video plans. Sorry for the confusion.
@SteveHoldaway
@SteveHoldaway Жыл бұрын
Thanks for the reply. It turns out it was an error in printing. I found that the 1 inch squares were only 23.5mm so scaled down by about 7 or 8 percent. I got the chair together after recutting some parts and it's worked out great!
@tswwoodworking
@tswwoodworking 11 ай бұрын
Glad it worked out. My computer/printer tried to reduce it as well. Auto correct on phone can be troublesome as well.
@52bmc
@52bmc Жыл бұрын
Great video! How much wood did you end up using? It looks like you only had a few boards there.
@tswwoodworking
@tswwoodworking Жыл бұрын
Thank you. I appreciate that. Rough estimate. Ended up being approximately 25 board feet, give or take a little bit. Arm boards were about 8 inches wide, which were the widest and were the first ones I had to select from my wood pile.
@paulwalker7227
@paulwalker7227 Ай бұрын
hey thxs from Australia🙃
@tswwoodworking
@tswwoodworking Ай бұрын
You’re welcome!
@JohnYerina
@JohnYerina 4 ай бұрын
the seat slats are 20" to make them fit they would have to be 21-1/2"
@tswwoodworking
@tswwoodworking 4 ай бұрын
Nope, seat slats are 20” and front stretcher is 20”. Temporary spacers are 18.5”. You can see this at 11:52 of video.
@asincich
@asincich 4 ай бұрын
Cheers from Argentina!!!
@tswwoodworking
@tswwoodworking 4 ай бұрын
Look forward to getting there someday!
@josenoriega457
@josenoriega457 Жыл бұрын
Podría enviarme la plantilla y las medidas de las madera. Soy un retirado que le gusta trabajar la madera y quiero ser util
@tswwoodworking
@tswwoodworking Жыл бұрын
There’s a link for free pdf plans in the description section below the video. It’ll open up if you click on it. Then you can print out the templates. Make sure printer settings are set to print at 100%. Gracias!
@woody1380
@woody1380 Жыл бұрын
Are these chairs hard to get in/out of? They look very low and tipped back which would seem to make life difficult but then everyone seems to say they are comfortable.
@tswwoodworking
@tswwoodworking Жыл бұрын
They are easy to get into…but have to lean forward and get your legs under you to get out. I could see some people may have trouble. But, yes comfortable to sit and relax.
@marynellburnett3046
@marynellburnett3046 Жыл бұрын
I'm a new subscriber I can't find the free plan to print, watching you make it looks easy, I would like to get the plans and make the chair
@tswwoodworking
@tswwoodworking Жыл бұрын
drive.google.com/file/d/1C8A1L3wLysGF9qkUGQIfO9NlyfET1aY2/view Mary, The link for it is in the video description. Make sure printer is set to 100%. Should be 1 x 1” squares. Square pieces are in the description too. Thanks for watching, subscribing and commenting!
@JohnYerina
@JohnYerina 4 ай бұрын
why is front stretcher 20"
@tswwoodworking
@tswwoodworking 4 ай бұрын
It is same length as seat slats. It is attached between front legs and long back legs rest on top of it.
@charliecoulter7558
@charliecoulter7558 10 ай бұрын
How long are the front legs and the vertical back support?
@tswwoodworking
@tswwoodworking 9 ай бұрын
(2) Front legs. 20 x 5 1/2" (2) Back Vertical supports 25 1/4 x 3" All the “square” parts are listed in the video description too. Let me know if that helps.
@wendyriley4636
@wendyriley4636 Жыл бұрын
Awesome! Thanks for sharing.
@tswwoodworking
@tswwoodworking Жыл бұрын
My pleasure!
@darekrusek2965
@darekrusek2965 9 ай бұрын
Hi, what is the thickness of the boards ?
@tswwoodworking
@tswwoodworking 9 ай бұрын
I planed it down to 3/4” thick
@aguinaldocarreiro
@aguinaldocarreiro Жыл бұрын
Parabéns pelo projeto e obrigado por compartilhar
@tswwoodworking
@tswwoodworking Жыл бұрын
Glad you like it. Thanks for watching!
@MichaelDunn-uc9kw
@MichaelDunn-uc9kw Жыл бұрын
How do I get a copy of the plans. I want to build a few. Michael Dunn
@tswwoodworking
@tswwoodworking Жыл бұрын
Hi Michael, Thanks for the question. There’s a link for free pdf plans in the description section below the video. It’ll open up if you click on it. Then you can print out the templates for all the curved parts. Make sure printer settings are set to print at 100%. Good luck with the build.
@severinocristovao9316
@severinocristovao9316 Жыл бұрын
Do you have plans to rocking chair legs? I'm in Brazil.
@tswwoodworking
@tswwoodworking Жыл бұрын
Sorry, no rocking chair. I did make one once that sat higher. It was easier to get out for someone with a disability.
@mikemurgante2173
@mikemurgante2173 9 ай бұрын
Enjoyed the video. I don't see a link to download the pdf plans
@tswwoodworking
@tswwoodworking 9 ай бұрын
The link for the curved templates is listed in the video description, and all the “square” parts are listed there as well. Good luck with your build.
@tswwoodworking
@tswwoodworking 9 ай бұрын
I should probably give a plug for the Folding Adirondack Chair video as well. I kind of like it better since able to store away for winter. Folding Adirondack Chair with Free pdf Plans kzbin.info/www/bejne/fnzam5WVet1rgcU
@HebronGrandpa
@HebronGrandpa 5 ай бұрын
Did you use all 1x6 boards?
@tswwoodworking
@tswwoodworking 5 ай бұрын
You could use 1x6s for everything except the arms, which are 6.5” wide….or you could adjust the template to make arms a little narrower. Depends on what material you have to work with. I always loved McGyver. Good luck 👍
@timeggers2294
@timeggers2294 Жыл бұрын
How about a folding Adirondack chair???
@tswwoodworking
@tswwoodworking Жыл бұрын
Good idea. I’ll keep that in mind for a future video.
@joseserrano7950
@joseserrano7950 Жыл бұрын
​@@tswwoodworking1²😂
@tswwoodworking
@tswwoodworking 11 ай бұрын
Used your suggestion. I posted a folding version with templates! Thanks for the idea.
@darekrusek2965
@darekrusek2965 9 ай бұрын
What is the material for the template ?
@tswwoodworking
@tswwoodworking 9 ай бұрын
I used 1/4” hardboard. You could use 1/2” mdf or plywood. I usually look through my rack and see what I have on hand. Hope that helps.
@emiliorobles4024
@emiliorobles4024 Жыл бұрын
Saludos desde santa Marta Colombia
@tswwoodworking
@tswwoodworking Жыл бұрын
Hola! Gracias!
@lesliekeyser3838
@lesliekeyser3838 Жыл бұрын
Can we get templates. Mike keyser Cary NC?
@tswwoodworking
@tswwoodworking Жыл бұрын
There’s a link in the video description to a pdf to print out to make the templates. (Set printer to 100%). Or are you asking if I sell templates?
@DavidRoncska
@DavidRoncska 11 ай бұрын
How much did it cost to build
@tswwoodworking
@tswwoodworking 11 ай бұрын
Well, that depends on type of wood and hardware you use. I went the more expensive route. I used stainless steel hardware which was about $25, and 21 board feet of quarter sawn white oak which is about $6/board foot. So total about $150. My folding Adirondack video which I posted recently was made from cedar which was less expensive.
@martinalvarez1137
@martinalvarez1137 10 ай бұрын
Gracias! 🙌
@tswwoodworking
@tswwoodworking 10 ай бұрын
De nada, tengo un video para silla plegable de Adirondack tambien. Hopefully my Spanish was okay. :)
@emiliorobles4024
@emiliorobles4024 Жыл бұрын
Cómo comprar plantillas dé la silla
@tswwoodworking
@tswwoodworking Жыл бұрын
La plantillas enlace esta en la descriptions de la bajo del video. My attempt at spanish :) The link for the templates are in the description below the video. Enjoy!
@JesseGoldsberry-m2q
@JesseGoldsberry-m2q 8 ай бұрын
Thank you
@tswwoodworking
@tswwoodworking 8 ай бұрын
You're welcome
@ThePelotkz
@ThePelotkz 5 ай бұрын
Круто. Спасибо
@tswwoodworking
@tswwoodworking 5 ай бұрын
Your welcome!
@ulecha4
@ulecha4 8 ай бұрын
Thank yoy
@tswwoodworking
@tswwoodworking 7 ай бұрын
You’re welcome
@emiliorobles4024
@emiliorobles4024 Жыл бұрын
Medias
@tswwoodworking
@tswwoodworking Жыл бұрын
Pies
@eirena495
@eirena495 Жыл бұрын
🤪 "Promo SM"
@tswwoodworking
@tswwoodworking Жыл бұрын
Thanks for the emoji/comment
@philliplindsay3829
@philliplindsay3829 Жыл бұрын
Hi, I am building these chairs. I followed your measurements in the comments below and cut the back slats to 32 " and tapering from 2.25" to 1.5". They look too narrow and dont fill out the top support. I see in your reply to a question from @user-sk4io9ob6v below that you state that the back slats are 35.5" by 2.75" !! What is correct please?
@tswwoodworking
@tswwoodworking Жыл бұрын
I mis-spoke to that question when I replied on my phone. That reply was regarding the more recent folding Adirondack Chair video plans. Yes, on the fixed Adirondack Chair I tapered the back slats and are 32” long. On the video I used the stated taper, but looked at another chair I’ve done and it was 2.5 to 2”. You can always add an extra slat as long as spaced consistently. Sorry for the confusion.
Did I Build a Better Adirondack Chair?
17:59
Fix This Build That
Рет қаралды 287 М.
You can make this Adirondack chair in a weekend
26:58
Steve Ramsey - Woodworking for Mere Mortals
Рет қаралды 107 М.
Как Я Брата ОБМАНУЛ (смешное видео, прикол, юмор, поржать)
00:59
How Many Balloons To Make A Store Fly?
00:22
MrBeast
Рет қаралды 154 МЛН
The Perfect Bench for Every Occasion.  Build it in 60 Minutes!
19:26
Adirondack Chair | Build It | Ask This Old House
7:53
This Old House
Рет қаралды 159 М.
Adirondack Chair  |  S2 E2
31:18
The New Yankee Workshop
Рет қаралды 218 М.
A Better Adirondack Chair?
11:22
Jackman Works
Рет қаралды 73 М.
How To Build An Adirondack Chair
17:16
PatriotDIY
Рет қаралды 4,1 М.
3 LEVELS of Adirondack Chairs -DIY to PRO Build
21:11
John Malecki
Рет қаралды 410 М.
Rockler doesn't want you to see this video
9:26
Busted Knuckle Woodworks
Рет қаралды 1 МЛН
10 COOL Homemade Tools that you really need !!
23:55
Start Making (Woodworking)
Рет қаралды 292 М.
I challenged a 78 year old to a build off
18:50
Lincoln St. Woodworks
Рет қаралды 4,5 МЛН
A smarter tool for small workshops
21:23
MWA Woodworks
Рет қаралды 328 М.
Как Я Брата ОБМАНУЛ (смешное видео, прикол, юмор, поржать)
00:59