McLeod Racing's own Fred Taylor talks about how to determine your "A" dimension and how to adjust for the proper clearance when using a 1400 series slip on bearing.
Пікірлер: 22
@keysersoze481610 жыл бұрын
You need to make many many more videos like this for other customers. Thank you McLeod
@nexdream18 жыл бұрын
This is exactly what i needed! Thank you so much!!
@3500camarz2 жыл бұрын
Excellent video tutorial!
@amil2017 Жыл бұрын
you did not subtract the thickness of the straight edge on both A & B measurements,
@santinocastillo81377 жыл бұрын
Can you make a video explaining what to do if the throw the bearing is fully extended, and is more than the clutch fingers need to disengage the clutch. and what do to stop it from overthrowing the fingers, that cause the prematurely wearing the parts.
@McLeodRacingClutches7 жыл бұрын
Hey Santino! Give us a call 714-630-2764 and we can help out. And thank you for the suggestion!
@anthonyi6025 жыл бұрын
Do one on an MT82 transmission that would be helpful as well
@jarrettwininger17914 жыл бұрын
With my tr6060 to LS1 I've got over an inch air gap and that's with the included spacer. Am I missing something?
@McLeodRacingClutches4 жыл бұрын
Sometimes you need an additional spacer to make up the gap. It is ok to stack two spacers, part number 1439.
@rayzor1967 жыл бұрын
Hello there can you please tell me what stops the slip on bearing from spinning??
@McLeodRacingClutches7 жыл бұрын
It has a constant running bearing on the front of it. If you have anymore questions, give us a call at 714.630.2764. Thanks!
@jeffchan91766 жыл бұрын
That does not answer the question. From what I can see the hydraulic lines will prevent the body from spinning.
@black33beard15 күн бұрын
@@jeffchan9176That seems like a lot of constant torque on those two lines.
@jeffchan91764 күн бұрын
@@black33beard1 I used this kit on a T56 Mustang. There is not alot of torque since the only force the lines will see are just from the drag of the bearing. Against all advice from McCleod. I used a small section of All Round Flexible Pipe Hanger to stop the drag from pulling the lines. It was flexible to not change any alignment of the non moving part of the body and if it ever broke, it would be no worse than nothing. After install. I witnessed the body to be totally stationary and had no regret about securing it.
@charlay709 жыл бұрын
awesome
@graysonholiday15823 жыл бұрын
The mt82 does not have a back face of the bell housing to measure to the teeth so how would you get the a dimension? I’m one of the idiots that does not understand the instructions 😂
@McLeodRacingClutches3 жыл бұрын
Hey there! Give our tech line a call and we can get you the measurement! 714-630-2764.
@jeffchan91766 жыл бұрын
You adjust forward to reach the fingers and you run out of thread, now what?
@McLeodRacingClutches6 жыл бұрын
Then you will need a spacer or a taller bearing. If you have any more questions, please call us! 714-630-2764.
@jeffchan91766 жыл бұрын
Why was this spacer or taller bearing not included in the kit MCL-327?
@McLeodRacingClutches6 жыл бұрын
Normally the customer does not need the spacer with that application.
@geerbangr Жыл бұрын
Dude says 200 thou, mcsplode says 100 thou clearance. What about the additional thickness of your straight edge? Zero stock in this guys video.