Showing how to install the FX Slug power kit in the Impact M3
Пікірлер: 225
@mastermighty2 жыл бұрын
according to Ernest row, the m3 only needs the slug probe. the valve and hammer spring have already been improved and upgraded. i also found when i fitted the entire kit i actually lost power only the slug probe is needed.
@Airbuks2 жыл бұрын
🤔 maybe there is a difference between US and EU models or they have updated this since I got my M3 ? I will investigate 😉
Very well explained and demonstrated. Thank you so much….step by step and not rushing. Excellent explanation as you were going. 👍👍
@Airbuks Жыл бұрын
Thx mate 👊
@fredbrackely Жыл бұрын
So what are the 2 little o -rings used for in the kit?
@infernoreviews2529 Жыл бұрын
Thank you very much for the vid. In the new power kits they don't include spacers anymore, I was affraid mine was incomplete but after some googling I found it out. Also very happy to know they don't use loctite on the M3's anymore, now all I need is a pair of vice grips and I should be able to perform this upgrade too. I was shooting some round nosed slugs made by Gmax ( .216 ) with the standard smooth twist barrel and no power kit installed ; 24gr @ 900/ 917, 28gr @ 870 and 31gr @830. They hit the target all over the place so I hope that the power kit and the heavy slug liner will give me the extra boost I need to shoot the heavier slugs accurately.
@Airbuks Жыл бұрын
Hi , yes indeed the new M3 models come or with the spacers installed from factory or the have a heavier hammer and so eliminate the need of that in the kit . About those GMax slugs 😬 I experimented also with them but indeed the don’t group for me aswel . If you need a good cheap slug that performs well take alsook at the JSB KO slugs 😉
@infernoreviews2529 Жыл бұрын
@@Airbuks ah awesome ! Thanks for the tip mate. My main problem is I can't use HP on the 50m lanes at the gun club here. Do you know any good solid slugs
@Airbuks Жыл бұрын
@@infernoreviews2529 slow velocity slugs with good accuracy 🤔 slugs need high velocity to get there accuracy so not really I had some good accuracy with JSB KO at 820fps once
@infernoreviews2529 Жыл бұрын
@@Airbuks right ! Thats why I will install the slug power kit and heavy slugliner. The only problem I have is that gmax is the only manufacturer for rond nosed slugs instead of hollow point (hp)
@Airbuks Жыл бұрын
@@infernoreviews2529 mmm 🤔 I see you mean hollow points with HP
@airgunsgt41082 жыл бұрын
I asked fx about the spk on the m3 and they told me this. You do not need to install the valve spring/rubber ball out of the slug power kit. The other parts are able to be used. Thank you. Best Regards, Melissa
@Airbuks2 жыл бұрын
Hi , thx for the info 👍🏻 I send the video to FX before uploading it to make sure I did everything right and nobody told me about that 🤔
@saltire5462 жыл бұрын
Another reason i think the L2 is an engineering masterpiece none of this messing around just put in the slug and fire .Thanks for sharing always very good quality videos.
@Airbuks2 жыл бұрын
Thx , the L2 also needs some regulator pressure tuning before it shoots accurate but less complicated indeed 👍🏻
@zsolezk Жыл бұрын
I sold my L2 for the M3 and could not be happier. The countless fiddling with the folding stock to reload, and the small magazine (only 8 bullets for a semi auto) took the fun out of it. for me. I do miss the semi auto aspect though.
@jerryking32082 жыл бұрын
Thank you. Look forward to part 2.
@Don.E.632 жыл бұрын
Very good video with good instructions on this procedure, thank you!
@Airbuks2 жыл бұрын
Thx 🙏🏻
@psychowim Жыл бұрын
Thank you for the professional demounting en reïnstalling video, this will be more than helpful. Thanks a lot 👍
@Airbuks Жыл бұрын
Thx for the support mate 👊
@thehuckleberryfactor29692 жыл бұрын
Thank you. I have one ordered and your video was awesome. This helps greatly. There is not much info on these except Meathead on You tube here in Australia.
@Airbuks2 жыл бұрын
Nice to here , you can also contact me on Instagram if you have any questions 😉👍🏻
@marcevens5472 Жыл бұрын
thank you so much for your reply , my trigger was lose before I started so I tightened iy the piece you actually place your finger on to fire . I've unloosened it again now the rifle id cocking! I attached my air bottle , now the rear regulator won't fill and im leaking air out seems to be around the plenum and around the trigger section almost like its coming out or the handle grip . im new to all this air rifle world so needless to say slightly lost
@Airbuks Жыл бұрын
Have you tried screwing on the bottle when the rifle is cocked?
@marcevens5472 Жыл бұрын
I've got the rifle to cock now ,but as soon as o try to get pressure in the back gauge is leaks air out on the 720 plenum . once again thank you for you time to get back to me
@Airbuks Жыл бұрын
@@marcevens5472 exactly where does the air leak out of the plenum?
@MrDirectNL2 жыл бұрын
Make a video on mounting the angled manometer bracket. It is nowhere on KZbin yet, you would be the first.
@Airbuks2 жыл бұрын
I just took delivery off one 👍🏻😉 video will come up soon 👍🏻
@KevinWood442 жыл бұрын
I just installed the angled bracket (weird that it comes with NO directions) only bizarre thing to figure out is that O-ring goes into the oblong looking hole by pinching the O-ring flat. Aside from that there is a TINY O-ring and only one hole it can possibly fit into, and it comes with a spare (thick/flat) O-ring for plugging up the original hole where the gauge used to be. I also am installing the pin probe tonight so this video is perfect! Much appreciated!!
@Airbuks2 жыл бұрын
@@KevinWood44 I still have to get to installing mine 🙈probably tonight. Did your slug kit come with 1 or two spacers and the rubber ball ? Some people reported that there is only once spacer these days and some reported that the rubber ball isn’t needed 🤷♂️
@KevinWood442 жыл бұрын
@@Airbuks 2 spacers and 1 rubber ball. Yours?? Hmmm....I wonder what benefit the 1 weight has over 2?
@Airbuks2 жыл бұрын
@@KevinWood44 I still had this kit from before the M3 got launched. So I have the full kit .
@raiwaheed27252 жыл бұрын
Very easy and informative stuff you share,its always very useful
@Airbuks2 жыл бұрын
Thx 🙏🏻
@setypa Жыл бұрын
Hello, made change to Slug power kit, but have problem with magazine. The needle does not want to go through the magazine. No problem without. All is .22 cal.
@Airbuks Жыл бұрын
Hi , maybe a stupid thing to ask 😉 but have you removed the sleeve that sits over the pin probe ? In 22 cal you need to remove the sleeve as the sleeve is used for 25cal
@setypa Жыл бұрын
@@Airbuks Sleeve was not installed. Absolutely don't understand where is problem.
@Airbuks Жыл бұрын
@@setypa are you using the original magazine? Did you measure the diameter of the probe ?
@precisionairgunninghunting62652 жыл бұрын
Always great videos. Some M3s have the washers as standard items
@Airbuks2 жыл бұрын
Thx , I didn’t know that 🤔 thx for the tip
@precisionairgunninghunting62652 жыл бұрын
@@Airbuks its weird, there's no consistency, should be all or none, not some. Maybe USA get it, or EU do. Not sure
@Airbuks2 жыл бұрын
@@precisionairgunninghunting6265 true
@Tom-fm2fh2 жыл бұрын
I wish I waited 1 day … it would have saved me so much head scratching
@Thommy-turbo8 ай бұрын
Hi, after installing the newer slug power kit with the larger tungsten weight instead of the 2 spacer. My valve adjuster wont go down to the last adjusting line. It bottoms out on line 2. Did i do something wrong or is this normal?
@Airbuks8 ай бұрын
That doesn’t sound correct 🤔
@thanh108908 ай бұрын
The rubber ball need to put in too.i heard some1 said take out the rubber ball will be increase speed.that right??
@Airbuks8 ай бұрын
In some cases yes
@Tom-fm2fh2 жыл бұрын
BIG THANKS
@simoncoher48412 жыл бұрын
Another great video and great explanation..
@seyhmusaltunsoz36752 жыл бұрын
Thank you 👍
@Not_Evil_ Жыл бұрын
Did it exactly like in the video, and I cant cock the rifle at all if set to 13 - 16 power setting.
@Airbuks Жыл бұрын
It means you have to much hammerspring tension , due to adding the spacers you create extra compression on the spring and your settings before might be maxed out . Adding both together results in being unable to cock
@EdBraunbeck2 жыл бұрын
If I understand correctly, the pin probe does nothing to increase power? It's mainly for accuracy purposes.
@Airbuks2 жыл бұрын
The hole kit increases power the washers and valve return spring create more hammerspring tension to open the valve at higher regulator powers while the pin probe allows for a better airflow true the transferport
@johnz5749 Жыл бұрын
'Thank you for your nice videos , i have the impact M3 sniper in .22 and i instal a heavy slug liner , a barrel tensioning system , the slug power' kit and the tungsten hammer but the rifle don"t cock above number 11 on the macro power adjuster , is the two spacer washers that cause the problem? Thank you in advance!
@Airbuks Жыл бұрын
When your powerwheel is at 11 at what level is your micro adjustment?
@tripleceas Жыл бұрын
Are folks keeping the slug power kit springs installed with the new power block? Or using the power block springs? I’m not convinced the slug power kit springs allow more power, with a power block application
@Airbuks Жыл бұрын
I still have it installed. I do believe it adds a benefit with the power block as that is improved specially for airflow and the slug power kit is designed to keep the valve open for longer time letting more air passed the valve . So both should help each other 🤔 in my opinion 😉
@jb05022 жыл бұрын
Perfect explanation. Thanks. Any change in the shot count after the kit?
@Airbuks2 жыл бұрын
Thx , shot count is very subjective. It al depends on what weight slugs you want to shoot at what speed . I am getting about 2.5-3 magazines out of a fill with 30gr slugs at 960fps
@ViktoKtp3 ай бұрын
May I want to know how to open the surrounded barrel on Laras?
@ericeverson68222 жыл бұрын
Love your videos
@Airbuks2 жыл бұрын
Thx Eric 🙏🏻
@ericeverson68222 жыл бұрын
@@Airbuks no problem love the detail you go into and the video reviews on different slugs
@Airbuks2 жыл бұрын
@@ericeverson6822 thx
@genghisghost Жыл бұрын
is it impossible to shoot pellets properly when you install this?
@Airbuks Жыл бұрын
If you keep the original probe not the pin probe then yes 👍
@amunraa1 Жыл бұрын
Hi,i have a question about the length you measured from 6,5 mm. According to the vid the Macro wheel was on 16, should it not be at 1? thx in advance
@Airbuks Жыл бұрын
As long as you didn’t overpowered the hammerspring tension it can be on 16 . If you can’t get to the 6-6.5 mm you can reduce the macro
@amunraa1 Жыл бұрын
@@Airbuks thx
@franckbecanfayeboue48772 жыл бұрын
Nice Video biddy. But tell me have you done the one for the installation of the 720 cc power plenum. If no, it would be great to get the update. Cheers
@Airbuks2 жыл бұрын
Hi mate , still waiting to get the 720 plenum for the mkii . But once i have it a will do a video offcours 👍🏻
@leoleen54912 жыл бұрын
please correct me we are doing that just to increase ftp on ~50 and less, right ?
@Airbuks2 жыл бұрын
Can you explain a little better what exactly you mean ? Thx
@leoleen54912 жыл бұрын
@@Airbuks what do you want me to explain ? I’m asking about reason to spend next 50 bakses for slug power kit by what reason ? To have +50 to FPS ?
@Airbuks2 жыл бұрын
@@leoleen5491 depending on caliber and the tune you use you can get more out of it .
@leoleen54912 жыл бұрын
@@Airbuks on your video, you have been using .22 cal, and upgrade gave about 50 FPS
@Airbuks2 жыл бұрын
@@leoleen5491 yes at the current tune I am using , it is possible to get more when upping the regulator as the mean idea of the slug kit is to make the hammer heavier to be able and open the valve and keep it longer open with the softer valve return spring.
@TheSopranosUkeDuo2 жыл бұрын
Great video, thank you. Can you use the pin probe and hi-flow port with pellets?
@Airbuks2 жыл бұрын
Yes you can but the seating depth can be a issue depending on what pellet you use regarding to the skirt depth
@TheSopranosUkeDuo2 жыл бұрын
@@Airbuks Thank you so much for your speedy and useful response.
@Airbuks2 жыл бұрын
@@TheSopranosUkeDuo you’re welcome
@james17952 жыл бұрын
I'm wondering why Utah Air told me the M3 doesn't need and a slug power kit because it doesn't make any difference to the M3 performance. When I ordered my M3 from them I asked them to install the kit and they convinced me it's a waste of money. I had a sour ordeal with Utah Air and I'm still not happy with my M3. I ordered a .25 and they sent me a factory .22 that they converted to a .25 with a used .25 liner. Also I am convinced the gun was used but they insisted that would be against their policy. I'm very bitter about the whole transaction.
@Airbuks2 жыл бұрын
Sorry to hear that mate , but I live in Europe and so I di t know how things are going there . It is possible that the recent models that are in the stores don’t benefit from the slug kit as I have heard some people say that the spacers are already standard installed on there M3 so the only thing to do is to install a pin probe and your done . Mine is one off the first M3 to be produced and I didn’t have the slug spacers in mine so I went ahead and installed them 🤷♂️
@james17952 жыл бұрын
@@Airbuks. Thanks. I do have a power probe. Do you happen to know the difference in the weight of the hammers?
@Airbuks2 жыл бұрын
@@james1795 the hammer should weigh all the same , but I don’t know how much
@james17952 жыл бұрын
@@Airbuks. Thanks for the reply.
@Not_Evil_ Жыл бұрын
16:40 for .30 cal I have to use the original pin probe right?
@Airbuks Жыл бұрын
There are companies like Huma that make a pinprobe in 30cal
@marcevens5472 Жыл бұрын
awesome video I've followed it step by step ,but now can't get the cocking mechanism to cock and hold back ? any ideas plese
@Airbuks Жыл бұрын
That means you have to much hammerspring tensioning. Just back off the 1.5 mm adjustment screw on the hammerspring adjustment
@medicnine3982 жыл бұрын
Why did you use the macro wheel to adjust back to " 6mm and a tiny bit" instead of continuing to screw it on? Was it as tight as it would go at that point?
@Airbuks2 жыл бұрын
At power 16 and micro 4.5 ( witch is about the max adjustment) the C1 measures 6,5mm I put them the power at 8 to see if I am not dropping below the 6mm , this isn’t a necessary step as installing the slug kit you are hunting for max power but for my piece of mind I always like to know where the valve is at at 1/2 power to understand some things better . Also some people reported the couldn’t get to 6.5mm as the had different springs installed or over adjusted the hs tension. Ow at max power the 6,5 mm is about as far as it could screw on yes , still had about 1/2 - 1 turn left on the threads
@medicnine3982 жыл бұрын
@@Airbuks Thank you!
@novitawulandari77712 жыл бұрын
Good
@airguns-shooter Жыл бұрын
I twisted the linkage what is the length of it ?
@Airbuks Жыл бұрын
I don’t know exactly by head but the best way to approach it is by marking the probe depth on the probe while you have the barrel out and then set it accordingly. I explained it in a few videos how I do it , there is also a vid somewhere on my channel with the general measurement
@hurricaneaquatics7 ай бұрын
Hey @airbuks does the 30 caliber M3 need the Slug power kit? It says for 22 and 25 caliber, so didn't know whether the 30 needs it or not. Thanks.
@user-kl7bz1bd5r Жыл бұрын
Does the impact M3 Power black version include "Slug Power Kit", "High Flow Pin Probe", "Power Tuning Hammer- and Valve Return Spring"?
@Greg343002 жыл бұрын
Nice video, thank you, I can't find you in the Slug Power store for the .35 model, the assembly is different to take advantage of the full power?
@Airbuks2 жыл бұрын
Hi , there is no slug kit available for the 35 cal is I am correct. I don’t have any experience with 35cal sorry 🤷♂️
@hdhighcounty2 жыл бұрын
Southern precision air weapons has the kit for 35 cal m3
@ladydemonika4202 жыл бұрын
Does the FX Impact Compact MK3 .30 caliber even need this? I helped a buddy put his in but once we got to the pin probe installation we noticed the 22/25 caliber adjuster was too small for the .30 caliber barrel and would slide all the way in to it not giving us a chance to mark the depth if that makes sense. It needed a bigger adjuster it seemed, like something that was already .30 caliber
@Airbuks2 жыл бұрын
Yes the slug power kit probe is made for 22-25 caliber if you want a pin probe for 30 cal you can find it at Huma Air
@ladydemonika4202 жыл бұрын
@@Airbuks nk you so much for responding as this clears a ton of questions! I know this is the pin probe but better safe than sorry, could you take a look at this link and please let me know if that is the cirrect part...
@Airbuks2 жыл бұрын
@@ladydemonika420 I don’t see a link but here is the link to the pin probe www.huma-air.com/FX-Impact-High-Flow-Pin-Probe
@ronb3862 жыл бұрын
Great video as always Brother! Installed my M3 SPK but noticed I could not turn the valve knob inward past the third line. The rubber ball was being compressed (unlike my MKII). Using using the M3 without the rubber ball for now. Any thoughts?
@Airbuks2 жыл бұрын
🤔 using it without the rubber ball isn’t bad but should not be like that . Do you still have the original hammerspring installed or is it a aftermarket one ( stronger/longer ) ?
@ronb3862 жыл бұрын
@@Airbuks The spring that came with the SPK was installed.
@Airbuks2 жыл бұрын
@@ronb386 that’s the valve return spring , I mean the hammerspring itself that sits inside the hammer
@ChrisFourt2 жыл бұрын
Hi!, same problem here, once I remove the ball, the problem was solve.. Cheers JCF
@juancarlos-rf5ko2 жыл бұрын
@@ChrisFourt Same problem, disassemble the valve cover and it already has a rubber ball in front of where the allen key is, tomorrow I will try without the rubber ball in the spring
@goodboyringo9716 Жыл бұрын
Can slugs be shot from the barrel the Impact comes with or do I need a slug barrel ?
@Airbuks Жыл бұрын
Lighter slugs yes but for heavier slug you best use a slug barrel
@saviofalcao670 Жыл бұрын
Hi mate. I just received my M3 sniper in .22cal. can i shoot 40g h&n slug by just installing slug probe with barell turning on slug port?. I want to shoot them at 950fps .. please advise
@Airbuks Жыл бұрын
I am afraid not , you will need to put a heavier hammer aswel (or install the spacers and valve return spring that come in the slug power kit )to open that regulator at 160-170 bar
@saviofalcao670 Жыл бұрын
@@Airbuks thanks mate...you always reply
@ResidentialRepairs2 жыл бұрын
Maybe I missed it but did you not use any threadlock for your C3 to keep it at whatever measurement you wanted throughout use?
@Airbuks2 жыл бұрын
You noticed right 👍🏻 in the video I explained that on the mkii I do use loctide but the M3 has a little different C3 with a rubber oring or thing inside that creates friction to prevent it from backing out . ( I have been told 😉)
@ResidentialRepairs2 жыл бұрын
@@Airbuks Thank you.
@honda160012 жыл бұрын
Hi, can you tell me why the end of the valve rod has to be 6-6.5mm please. When I tighten mine I get just under 5mm. For me to get 6.5mm it won't be tight tight. Have I got it wrong? Thank you, your videos are 👌
@Airbuks2 жыл бұрын
No nothing is wrong . If you put your macro wheel on 8 and micro on 3 then turn your macro back to 16 so the micro ends up around 4 I think the C1 measurement should be between 6 to 6.5 mm
@honda160012 жыл бұрын
@@Airbuks hi, thanks for the reply, I commented on the wrong video. I was meant to comment on your other install. My impact is the mk1 with the power plenum, does the same apply? Tighten the hammer seat tight and it should be ok? I've seen another video, the guy loosens the hammer seat to get 6.5mm. Won't that cause power fluctuations because its loose?? Thanks again for replying 🙂
@Airbuks2 жыл бұрын
@@honda16001 in that case it’s just a little bit different, in my mkii I put blue loctide on it and screw it to +-6.25mm let it sit overnight before I shoot it and you should be fine . Just beware the amount of adjustment you made on the internal hammerspring screw can make a difference
@honda160012 жыл бұрын
@@Airbuks thanks again for replying, really appreciate it 👌👍
@attk19842 жыл бұрын
What was the length of the first barrel you had on at the beginning of the video? Just to confirm the tank 580cc.
@Airbuks2 жыл бұрын
That was a 600mm barrel with a 580cc tank 👍🏻
@lassesarnhult92832 жыл бұрын
When I try to pull out my C3 it is like it is stuck in a spring and it just to go back in again what am I doing wrong. There has never been an adjustment om there because it was a sub 12 before. Help!!
@Airbuks2 жыл бұрын
What generation impact do you have ?
@lassesarnhult92832 жыл бұрын
@@Airbuks A new M# just one weeks since I bought it
@lassesarnhult92832 жыл бұрын
@@Airbuks M3
@Airbuks2 жыл бұрын
@@lassesarnhult9283 if it was a sub12 there might be a return spring on the valve in the plenum to help with the lower reg pressure. But I don’t have any experience with sub12
@timw56272 жыл бұрын
Puramyd Air says not to install the rubber ball when installing the power kit in the M3, it's on the web site when you grouse that item, any thoughts on this??
@Airbuks2 жыл бұрын
I have had the same question from someone else, I have tested it . Installing it doesn’t hurt your gun but you can gain more power without it 😉👍🏻
@juancarlos-rf5ko2 жыл бұрын
@@Airbuks la valvula ya trae incluida una bola de goma, si le sacas la allen la veras
@martinbarron65452 жыл бұрын
Just received my power kit and it did not have the rubber ball?
@Airbuks2 жыл бұрын
🤔 , but in my case I took it back out to get some more power 😉
@stevo9052 жыл бұрын
Thanks for the video,is this the .25 caliber?
@Airbuks2 жыл бұрын
No original it was a 25 but in this video I ended up making it a 22cal
@jaadmaan81562 жыл бұрын
18:06 that screw stripped instantly for me when i tried to undo it. what would you do?
@Airbuks2 жыл бұрын
Yes that’s a small screw that easily strips 🙈 I would take the cocking rod out and gently try to drill it out . Or heat it up so the glue melts and try again Or glue your Allen in the screw overnight and try again
@nephtalilucero80842 жыл бұрын
How does power kit affect pellets. How much faster does it make the slugs? Thanks for info.
@Airbuks2 жыл бұрын
How much faster I can’t really put a number on it 🤔 but if you want to shoot with a higher regulator pressure 150+ you need some more HS to get the valve open far enough and long enough to get them up to speed . For pellets you don’t need the slug kit , but it’s still possible to shoot them as long as you bring the FPS back down with the powerwheel
@nephtalilucero80842 жыл бұрын
@@Airbuks thanks good to know.
@dimawar23282 жыл бұрын
👍
@simoncoher48412 жыл бұрын
Hi mate took my M3 out in .25 yesterday everything going great it has had a slug power kit put in like I said very accurate ect took it out to 80 yards lovely tight groups but then I noticed when I went to reload the mag again the pellet probe was bent gutted as only used it for a few hours , why do you think it would be bent was it not install properly? At the time I was using JSB Heavy pellets didn’t even try the slugs. Also did you have to adjust your trigger on yours as I definitely can’t feel 2 stages just 1 long pull. Thank you for any advice .. Simon..
@Airbuks2 жыл бұрын
Hi Simon , you have te pin probe installed I presume? Is it possible that by inserting the magazine you bend the pin , if the pin is set to much forward it is possible that you bend the pin that way 🤔 Regarding the trigger no issue by me , but it’s easy to fix that . Make sure you read the manual to adjust the right screw 😉
@simoncoher48412 жыл бұрын
@@Airbuks Thanks for getting back yes I have the shop I bought it from put it in power kit it was fine at first done some great groups at 80 yards then noticed probe when took mag out , Aso forgot to mention so as you know never owned a fx before come from S510R, The M3 so when the mag is out and you pull cocking lever back silky smooth , but when magazine is in its not its rough or notchy if you know what I mean is this normal for them very mechanical if that makes sense.. Thank you for your advice 🙏
@Airbuks2 жыл бұрын
@@simoncoher4841 did you check if the probe is tightened well , sometimes it can make itself loose
@simoncoher48412 жыл бұрын
@@Airbuks will do thank you, Also forgot to mention so as you know never owned a fx before come from S510R, The M3 so when the mag is out and you pull cocking lever back silky smooth , but when magazine is in its not its rough or notchy if you know what I mean is this normal for them very mechanical if that makes sense..
@piercingrules2 жыл бұрын
The rubber ball musn't go in the m3, it's only for rhe older impacts
@Airbuks2 жыл бұрын
Yes , I informed the viewers in a updated video later on. 👍🏻 it doesn’t harm if it’s there but you can’t make the most power out if it then
@mulleexx2 жыл бұрын
HELP! i did everything at the same way but no pressure on second regulator.
@Airbuks2 жыл бұрын
Hi , strange that the second regulator doesn’t get air 🤔 as the process doesn’t need the regulators to be touched. Have you have adjusted the first reg by any chance?
@emilbaligod19352 жыл бұрын
Did you ever experience the second slug blocks the slug probe when cocking?
@Airbuks2 жыл бұрын
No not a issue but me , are you sur the pin of the probe isn’t to far out ?
@emilbaligod19352 жыл бұрын
@@Airbuks That is the cause. It needs a little trial and error to adjust
@antoniocoppola59962 жыл бұрын
if i buy a FX Impact M3 - cal.25 sniper, is the kit useful to increase the power? should i buy it as well?
@Airbuks2 жыл бұрын
Yes but it’s aimed more to shoot slugs , if you just want a pellets shooter you don’t need it 👍🏻
@antoniocoppola59962 жыл бұрын
@@Airbuks tnx a lot for the suggest, i will buy coz is interesting upgrade
@alexanderpinto1242 жыл бұрын
what happened to the review of the Leshiy 2
@Airbuks2 жыл бұрын
Still working with the L2 , don’t worry. I have a small issue with the EAR and I am waiting for a new part to be shipped to me before I can continue the videos with the L2
@AboveTheSystem2 жыл бұрын
What about .177 (4,5mm)?
@Airbuks2 жыл бұрын
I have no experience with 177 , sorry
@chefrenty9155 Жыл бұрын
Hello again. I moved to this video because it's more appropriate when using the M3 afterall. Sorry for the inconvenience. Your Video is a great help! I've installed the first part of the slug power kit according to Your clear video, the placement of the two washers for the Hammerspring and the new lighter Valvespring. 1. Unlike You showed in Your video, after installing, I measured the C1 6,5mm at powerwheel 16 but only 6,4mm at powerwheel at 8 instead of 6mm. Is this normal? 2. After installing the C1 again, You put the C1 with Rod complete inside to the end and check if You see it on the Silver part where Your magazine goes in. Here the end of the Rod is almost less then a mm inside from the wall (Magazine side). Is this correct? 3. After installing the Valveknob, I cannot go lower then Line 2, coming from Line 3, it goes heavier and heavier and complete stucks at line 2 ( Cocking goes normal as before (a little bit heavier) at Powerwheel 16). How can this be? In all honesty, I have to say that, when I purchased the Gun, I couldn't get lower then line 1 - 1,5. So, when shooting, I think the Valve didn't open enough then, so the pellet didn't leave the Barrel. Thank You again very much in advance for Your Advice.
@Airbuks Жыл бұрын
1. Try to put the power wheel at 8 and micro at 3 . And then measure it 2. That can be depending on the tune and parts installed 3. That’s very strange 🤔 are all the internals original oem parts ? Sounds like there is a longer heavier spring inside or bigger hammer . This in combo with the 2 spacer might cause that there isn’t enough room inside and everything binds up
@chefrenty9155 Жыл бұрын
@@Airbuks Thanks for Your reply and suggestions. 1. At powerwheel 8 an micro 3, nothing changes, still 6,4mm. Before the upgrade I measured 6,2mm on Powerwheel 16. 2. Ok 3. The buks isn't changed, all part are original as purchased. Is it possible the position of the 4 lines/groove isn't right? I measure about 15,5mm from the outside (with the hex 11mm) to line 1. Line 4 is then about 11,5mm. The inside pin in the Knob where the Spring goes around, is getting stuck to the end of the rod. When I put the Knob on the Valve housing on line 1 first and screw them together back in (without valvespring), the Chest has still 2mm to go when it stucks. That matches the distance between line 1 and 2 I cannot reach. I've done some measurements and it seems imho there are 3 possibilities: A. the Rod the C1 is screwed on, is too long or B. the C1 has to move 2mm more inside or C. the Pin in the Valveknob has to be 2mm shorter. I'm not sure, but with the Valveknob at line 1, stays the Valve completely closed due to the max tension of the Spring or goes just a litle bit open? Thanks in advance for Your opinion
@chefrenty9155 Жыл бұрын
Sorry, at point 3, I typed 'stuck to the end of the Rod', I meant 'stuck to the end of the C1'
@Airbuks Жыл бұрын
@@chefrenty9155 the measurement has to be between 6-6.5 mm so you are good there . So without seeing the impact if you can get a measurement between 6-6.5mm this tells me that the valve rod is not to long . It could be that the valve housing isn’t installed properly causing the impression that the valve rod is to long or there might be something wrong in the valve knob . What valve return spring are you using ? Are the internals installed in the correct order ? Again without seeing the gun I can only guess
@chefrenty9155 Жыл бұрын
@@Airbuks Now I'm using the lightest spring, from the powerkit. I did The latest measurements without the Valvespring installed. Ik have the Hammerspring, Hammerweight, Hammer and the 2 washers installed as shown in Your Video. Is it correct, that at line 1 (Line 2 in my case) the Valve could not be opened by the Hammer (stays closed) and at line 4 or a little bit further, the Valve could be opened max? Iám curious, can You go lower then line 1 with Your Valveknob or is Line 1 the lowest setting? I think, I gonna try the Gun first (without the new Pelletprobe) how it performs now and come back later again with the results. There has to be some improvement (I hope)... Thanks in advance.
@giuliocantarella22742 жыл бұрын
for caliber 0.30 is used the same kit as for caliber 0.25?
@Airbuks2 жыл бұрын
The kit is the same , but you have to make sure you get a .30 pin probe
@giuliocantarella22742 жыл бұрын
@@Airbuks and where can I buy a 0.30 pin probe? do you have the link?
@Airbuks2 жыл бұрын
@@giuliocantarella2274 Huma air has one ☝🏻
@giuliocantarella22742 жыл бұрын
@@Airbuks 👍
@tkielek242 жыл бұрын
On the mk2 power wheel need to be what number 2. Or Max??? And C1 6.-6.5mm ??? Thanks for video
@Airbuks2 жыл бұрын
Hi Tomek , can you explain in more detail. Not 100% sure what you mean , sorry
@tkielek242 жыл бұрын
@@Airbuks Okay Measurement C1 need to be anywhere from 6-6.5mm. But You was checking your power wheel. And i think your power wheel was set On@16. C1 measure was something like 6.5 mm Later you change power wheel to @8 i thing and C1 measurement was 6.mm So my question is when i install this FX slug power kit i should put hammer spring on max. Power wheel on Max and install this kit and C1 need to be anywhere from 6-6.5 mm Thank You!!
@ronb3862 жыл бұрын
@@tkielek24 From all the other vids I watched, power wheel should be set to “Min” to relieve spring tension, before taking measurement. This is how I set my C1 measurement.
@Airbuks2 жыл бұрын
@@tkielek24 oké now I get it 👍🏻 The best way to do it is to put your wheel ( macro ) on 8 then adjust the thumb wheel ( micro ) to 3 . Put you Macro wheel back to 16 ( the micro will be around 4 I guess then ) and then you measure the C1
@tkielek242 жыл бұрын
@@ronb386 Question. So I need to set my power wheel at minimum. Mk2. Of course and C1 measurement 6.5mm correct?
@collinswisher25122 жыл бұрын
Do the m3 and mk2 use the same slug power kit?
@Airbuks2 жыл бұрын
Yes , but some places in the the M3 has the pacers installed already from the factory and the only thing you need is the probe
@collinswisher25122 жыл бұрын
@@Airbuks awesome, thank you
@nephtalilucero80842 жыл бұрын
If air leaks out of the barrel after install what could it be?
@Airbuks2 жыл бұрын
Have you fixed the problem?
@nephtalilucero80842 жыл бұрын
@@Airbuks yes i did. Thanks! That was an old post before you helped out.
@Airbuks2 жыл бұрын
@@nephtalilucero8084 sweet ! Sometimes I forget stuff 😉
@nephtalilucero80842 жыл бұрын
I did the kit for fx impact ii. For some reason its letting all the air out through the front of barrell. Very fast
@Airbuks2 жыл бұрын
Most likely there is a issue with the valve not closing properly, This can be caused by a few things My advice is to disassemble it again and see if you have everything installed correctly
@nephtalilucero80842 жыл бұрын
@@Airbuks yea you are right, man i took it all apart and come to find out the new valve spring with the ball is too week to close it at the end part on the block by the plenum. I installed the old spring and put the ball in there and that worked. Do you think its because i have the hammer knob adjusted to the max? I currently have it on minimum while doing this but i adjusted it to the max. Not sure if that has anything to do with it
@Airbuks2 жыл бұрын
@@nephtalilucero8084 i thinking might have to do with the regulator pressure you use ? Can you tell me at what pressure your second reg is ? If you say that replacing the lighter valve return spring fixes the issue I suspect that you have a lower regulator pressure to shoot . When shooting at higher pressures the valve return spring doesn’t do much work as the higher regulator pressure is what closes the valve , but with lower pressure on the reg the spring tension is needed to close the valve strong enough to keep it from leaking out of the barrel
@nephtalilucero80842 жыл бұрын
@@Airbuks i cant imagine its the preasure. I forgot what i had it on before air went out. No less than 125. I noticed in your video thst yours went right flush without yet having preasure. Mine i had to oush it back and hold it back with finger in order to measure how much the C was sticking out. I measuted 5.5 mm before i took the C off and i out it back on that measure afterword. But i had to push with finger to measure. Telling me the hammer spring is resisting quite a lot. As soon as i put the tank bottle on all air started to come out.
@Airbuks2 жыл бұрын
@@nephtalilucero8084 try reducing the hammerspring while installing the C1 and set it at 6-6.5mm . There shouldn’t be any resistance or holding it with your finger to measure it
@ronalsnd20 күн бұрын
what caliber
@hightidelowtide63802 жыл бұрын
Too much work for for an expensive rifle. Fx should sell the slug kit as option already installed
@Airbuks2 жыл бұрын
Not a bad idea 🤔
@vannong73362 жыл бұрын
Khẩu súng này có giá bán bao nhiêu tiền vậy ạ
@Fernando_Woolybooger2 жыл бұрын
Can this be installed on the .30 Caliber?
@Fernando_Woolybooger2 жыл бұрын
@@Airbuks What about the lighter spring and rubber ball? Install that in the .30? Thanks!
@Airbuks2 жыл бұрын
@@Fernando_Woolybooger you can try that but in the M3 in my personal experience and tests in 22 cal I got a better balance with the original spring and no rubber bal 😉
@Airbuks2 жыл бұрын
@@Fernando_Woolybooger You can try that but in my personal experience and test I have a better balance with the original spring and no rubber bal . But in 30cal it could be that you can benefit from the lighter valve return spring and you can lower your hammerspring to open the valve far enough 🤔
@moekakke2 жыл бұрын
You forgot to remove the o-ring on the pin probe because it won't go true the magazine... ;-)
@Airbuks2 жыл бұрын
Not a problem buy me in a next video you can see it cycles fine without any issue 🤷♂️
@moekakke2 жыл бұрын
@@Airbuks It's only there to seal the sleeve part to .25 call. Mine got stuck in the magazine then i realized it was not needed there. Great video by the way !!
@lorenzorommelaere91322 жыл бұрын
Wat is het grootste voordeel van de kit
@Airbuks2 жыл бұрын
Wat meer power om zwaardere slugs te schieten 😉
@lorenzorommelaere91322 жыл бұрын
@@Airbuks meer power met dezelfde hoeveelheid lucht?
@lorenzorommelaere91322 жыл бұрын
Wel benauwelijk om dit te doen als je nog nooit een buks uit elkaar hebt gehaald.
@Airbuks2 жыл бұрын
@@lorenzorommelaere9132 neen dat niet 😬 alles staat in verhouding. Meer power meer lucht 🤷♂️
@Airbuks2 жыл бұрын
@@lorenzorommelaere9132 als je nog nooit een buks uit elkaar gehaald hebt zou ik zeker niet beginnen met een Impact 😬
@AntonioLopez-jg1gd2 жыл бұрын
Hola te vuelvo a pedir por favor los subtítulos en español El segundo idioma más hablado del mundo Y el tercer idioma más utilizado en Internet Gracias
@user-eu7py4qs6c2 жыл бұрын
You are speaking like the robot 🤖 😆🌹
@Airbuks2 жыл бұрын
As long as you can understand me and the video can help people I am more then happy to sound like a robot 🤖😂