Airsoft AEG Compression parts install tips and guide

[@mzarnott]

One of the best videos I have watched with loads of stuff I never check. I’m 200% better for having watched this. Thank you!!!!

[@MojoTheGreater]

The nozzle/huu explanation was really good. Thanks, mate!

[@mpoT3CHY]

Thanks for including the hop chamber setup and relationship to the nozzle. A lot of tutorials skip this step however it is one of the most vital areas in the entire build.

[@wyshtechairsoft]

I might actually clip that part of the video to make a separate video. I see too many people having issues with misfeeds when they swap over to the Maxx hopup. It would be great to refer newcomers to teching to that part of the video. If not, the whole thing.

[@maxaladin8924]

hi from Bulgaria :D thank you very much for your video im a beginer but i did leran much for very short time thanks to you god bless you!

[@martinjensen257]

Really good film for those who haven't tried it before.

[@wyshtechairsoft]

Thanks for the feedback! I made this video for those who need advice and I can reference to.

[@christianvillarroel980]

very well detailed stuff! I usually dont have patience to watch long videos like this but this is amazing. thank u

[@wyshtechairsoft]

Glad to help! And thank you for the input!

[@jmamcj]

Just discovered your channel a few hours ago. Lovely videos, lovely ideas. Thank you!!

[@wyshtechairsoft]

Glad you enjoyed the videos!

[@Junisthelast]

Hey quick question what is the purpose of the singular bushing you have installed on the bottom of the spur gear when you have a bearing on the top of it? Sorry I’m new to teching so I was genuinely curious

[@wyshtechairsoft]

Its mainly due to that particular bushing recieves the most stress whenever there is a PME with the piston or gearbox lock up. A bearing will always fail right there. I prefer using bearings whenever I can to reduce amp draw and increase cycle rate for better trigger response and smoother gear meshing.

[@mikewasauski-gc4ii]

very well detaile and very helpfull

[@wyshtechairsoft]

Thank you! Glad to help and educate. Also I recommend joining our discord for more assistance! We have a dedicated channel called #airsoft-tech-help where its easy to ask questions and get answers from myself or the community! Link is in the description or in my bio.

[@mikewasauski-gc4ii]

@wyshtechairsoft I'm 100% joining the discord cause I just bought a bunch of things, and I can not wait to put them in my rifle

[@wyshtechairsoft]

@mikewasauski-gc4ii right on!!

[@darkshock42mlg05]

i have a shs g36 nozzle in my sr25 and I'm not getting the consistency I should be getting. if i do the compression test you can heat the air leaking from the nozzle. i know its possible to get perfect compression there because I've done it with my cyma plat mp5. I first tried a Maxx nozzle and no luck. I'm not spending $100 on Maxx parts when stock cyma parts are already good. not to mention I can't even use a Maxx nozzle. I then tried a shs nozzle which was a tight fit, but it worked and perfect air seal. I don't know why shs isnt doing it this time if it worked before. the compression at the cylinder is fine but my power is below what it should be on a guarder sp120.

[@wyshtechairsoft]

What gearset brand are you using?

[@rommeltolentino942]

Do you know how to use 32:1? For 170 guarder spring?

[@wyshtechairsoft]

Yea but its pointless to use that ratio because of brushless motors. Especially motors that have adjustable rpm.

[@Jay19299]

Hello, I just took my EMG umbrella m4 apart for the first time. When I got it back together and shot it the first time, the BBs shoot out about 10 feet. Basically rolling out. I thought I put it back correctly, what should I check? Thank you for your help.

[@wyshtechairsoft]

First, what was it taken apart for?

[@Jay19299]

@@wyshtechairsoft The reason was for a grinding noise, I assumed it was gear’s grinding in the gearbox . Once apart the only gear wear I saw was the gear that is on the end of the motor. I then realized it was able to be adjusted, I adjusted motor/ gear tighter (in). The noise went away. However now I believe I may have put something in incorrectly and now it doesn’t shoot the bb. Im curious if I needed to time the sector gear and the piston differently. Thank you again for responding and helping.

[@wyshtechairsoft]

@Jay19299 you might of forgot to put the tappet spring in. Thats easy to check by pressing the nozzle inward and see if it pushes back.

[@Jay19299]

@@wyshtechairsoft just check nozzle, it wouldn’t move back or forward. I split the gear box, it now moves freely and tappet spring was connected. Could it be how I aligned the gear to the piston?

[@Jay19299]

@@wyshtechairsoft got it! I didn’t have tappet plate in the nozzle notch. Thank you a ton for your help. I wouldn’t have thought to look there without you helping!

[@sammyg7539]

Hi! I followed all the steps in the video but i stil have fps loss and mis feeds

[@wyshtechairsoft]

Hmm.. I think this would be easier to handle on our discord channel. We have a dedicated channel called #airsoft-tech-help where its easy to ask questions and get answers from myself or the community! Link is in the description or in my bio.

[@hypercube3495]

Do you release this video 7 days after I made my first build😂 it's going to be really helpful on my second great video! I also have a question I'm having trouble with a replacement trigger assembly binding like crazy. I cannibalized it from a lancer because into a (old 5+ yrs) g&g gearbox shell it binds open and closed but I can't see what it's binding on maybe the simi lever? Do you know what could cause this?

[@wyshtechairsoft]

Thank you for your kind words! Its inspiring. As for your trigger. Without seeing it, my guess is that the trigger might be too wide for the gearbox or the axles of the trigger are too thick.

[@reflexgaming342]

Hey, I have a question: I have a CYMA Sport ar-47 (sr-47) and I have no idea how to program the MOSFET. Would you happen to know what I need to program it and how?

[@wyshtechairsoft]

Sports dont come with a mosfet from the factory. If it does, then it's more than likely an aftermarket, so you'd need to find out what brand and model it is. Unless it's a Platinum edition.

[@reflexgaming342]

@@wyshtechairsoft Hmmm. I really thought it had a mosfet. Whenever I plug in the battery, it plays a little chime. I thought that indicated the mosfet turning on.

[@wyshtechairsoft]

@reflexgaming342 Do you have the link to this rifle? The description might say it has the ZUES mosfet in it, which would be an exception to what I mentioned. Which that mosfet is just basic and cannot be programmed. However you can upgrade to replace it with one that you can.

[@reflexgaming342]

Can you see my replies? KZbin keeps taking them down.

[@reflexgaming342]

​@@wyshtechairsoftDo you have an email I could use to send you some pictures of my gearbox?

[@martinjensen257]

Are there any sorbo pads that you can recommend.

[@mpoT3CHY]

He mentioned sorbo is an obsolete method and it is better to get a set of metal washers for the piston head to adjust AoE.

[@wyshtechairsoft]

If your really need to use sorbo pads. I recommend begadi sorbo pads from begadi.com

[@BeWolf.]

Excellent content ! 😎👌🇧🇷

[@wyshtechairsoft]

Thank you!

[@nickxatzh]

O my god....too much i formations for only one vibeo!!!!🙏🙏 As always to the point man.. I have learned many things from your videos....no i am building a mk18 for 1.2 joule and 1.65 joule with a t238 brushless 33k and 13:1 gears..I want your opinion as expert...how to shortstroke the sector??3 or 4 teeth from the front?or 2 teeth from front and 1-2 teeth from end? I thing as a better setup the second one..but i want your experience man🙏🙏

[@wyshtechairsoft]

You should only need to take off 3 teeth. Personally, I prefer to take 2 off the release and 1 off the pickup to prevent tappet pme. Glad to help!!