Align Your Arrows on the Blendjet 2

[@lisawilkinson6147]

Thank you for this instructional video. I had used my Blend Jet 2 just once and could not figure out how to get the arrows to align. I hadn't noticed the arrow on the measure/container. I also found that the gasket in my unit needed to be reversed groove side up. Without your post and the comments that followed, I would not be able to use my Blend Jet at all!

[@HealthyWayILive]

So glad it helped you!!

[@starlvs]

What is the gasket?

[@kathiajavier9343]

Thank you for your comment. I had the wrong gasket on. Now I can use it.

[@munazashahbaz2484]

Thank you so much for showing me how to align it. It does work, now i can finally make some smoothies.

[@HealthyWayILive]

Awesome!!!!

[@sanjobo]

Please add this to you video ...... make sure the gasket in the blender under the blades is right side up, the groove in the gasket must be facing up or you will not align. I was so frustrated that it wouldn't align I was ready to send it back but called Blend Jet and they informed me about the gasket, it lined right up on the first try. PS: your video is great.

[@piehunter2962]

Whats a gasket

[@sanjobo]

@@piehunter2962 ....... Hi .... the gasket is the grey rubber flat ring inside the blade area.

[@sumbxdy_says]

Thank you so much, you're a life saver!! ❤ I wonder why they send it with the gasket facing the other way around though. Does it not cause any leakage issues if you turn the gasket around?

[@sanjobo]

@@sumbxdy_says ... you are very welcome, I'm glad it worked for you ...... I have had NO leakage issues after turning the gasket over to the correct direction.

[@Jennifr1966]

QUESTION: Why does my blender leak from bottom when I dump liquid OUT?

[@user-ul4fg8kc1c]

My Blendjet worked on arrival but the arrows were misaligned by approx. 5mm. When I tried to remove the tube it was too tight. My son eventually undid it but then we were unable to get the arrows lined up. Didn’t think it was the gasket because we hadn’t touched it. However, it was the gasket, in the wrong way so now it works. So if yours doesn’t work even though you have not touched it (probably put in wrong at the factory and worked because a machine tightened it up more than we can by hand) turn the gasket over and it should hopefully work.

[@charpecoraro7213]

Thanks. It was the gasket. Was upside down from manufacture

[@main2333]

Wow. For the longest time I wondered why my new blend jet wouldn’t start. Kept seeing for jet 2. It works now! Thank you! Sometimes I want something smaller than my nutri bullet. Lol. Just saw I have the two. But yours showed right away to solve my issue. Thank you!!

[@HealthyWayILive]

So glad I could help! 💛

[@jenniferssugarcookies6031]

The only way this works for me is if it is not completely on. No matter where I start the screwing it will not line up.

[@debraparrott8568]

Rubber seal probably in upside down. Grooved side up

[@Justyna_N]

@@debraparrott8568mine won’t align properly either and the uneven side of the gasket is facing up

[@CrimsonRaven51]

I have the large jar attached to the base. I blended a drink with pineapple and banana. Now, it’s like the jar is fused to the base. I can’t unscrew it with all my strength. What happened? Have to buy a new one?

[@albanogueiramiser]

Same my jar is stuck too did u figure out what to do??

[@naliyad1239]

I have the same issue it just won’t open up 😭

[@catalinaocampoacosta6460]

The same my jar is stuck :(

[@raindrop9247]

Thank you~~~~ I was trying to figure out the removal of the bottom ring. THANKS!

[@HealthyWayILive]

You’re welcome! Glad I could help!

[@rasikacheswayampakghar]

I purchased today blendjet2 in india, I have one query is the blade panel not middled? Like is it kept off set purposely to blend... because after unwrapping I was puzzled and thought its defective product here there is no call center no. To address my query..

[@HealthyWayILive]

Hello! I’m not sure to be honest. Mines was the same way but it still worked fine!

[@debraparrott8568]

Where do we start the arrow on the jar to stop in the right place?

[@HealthyWayILive]

Try to get the arrows aligned the best you can

[@HealthyWayILive]

Turn counter clock wise

[@Justyna_N]

@@HealthyWayILiveturning counter-clockwise unscrews it

[@tomdavidson9451]

Hi, mine leaks when the arrows are aligned and when I screw it tighter it flashes red, I’ve tried for ages

[@brooklynthomas7607]

Make sure you don't have the gaskets mixed up. This was my issue. The top gasket was on the bottom and the bottom gasket on the top.

[@debraparrott8568]

Check bottom rubber seal. Grooved side up

[@annie.ppinnix6565]

It’s 9:58. I’m having trouble with the arrows line up it’s my first blender jet I’ve only use it maybe 4 times

[@jenniferssugarcookies6031]

Ok, my BlendJet 2 does go on. It never aligned. I called the company and they say it just has to be near the arrow. You just have to find the sweet spot. It’s close

[@Jennifr1966]

HARD LESSON LEARNED: Keeping jar above sink (in case it leaks), add water first. If it's fine, you aligned like she said. If it leaks, either you didn't do it like she said, or if you've had it a long time, time for new seal@

[@pmf598]

After deep clean , got the plain gasket in the top and the groove facing up gasket in the bottom . Screwing glass on evenly but glass arrow goes past body arrow , light flashes red and purple and will not work. Do you know what is the problem please ?

[@HealthyWayILive]

Maybe your rubber pieces are not back on correctly. Try changing them around

[@pmf598]

Just answered my own question . . . . advice on this thread says grooved gasket in the base should be groove facing up . This didn't work , groove facing down made it work .

[@pmf598]

@@HealthyWayILive Yes , as you can see i have also replied to myself about this , if the rubber gaskets are not correctly positioned the blender will not work . Groove must be face down on the bottom part , not face up , and piece with no groove goes in the top .

[@HealthyWayILive]

I replied before you replied back to yourself but I’m glad you got it straight👍🏽

[@pmf598]

@@HealthyWayILive Thanks , yes it was the gasket problem , they not put in correctly it will not work , and a bit fiddly to put the grooved one in . All good now , cheers .

[@dianek6915]

Thank you🙏 That was very helpful but I still can't get mine aligned😁

[@HealthyWayILive]

Make sure to turn it counter clock wise evenly on there

[@Gamesake2]

I just can''t get it. The arrow won't ever go to that point. By the time it screws tight, it's either far past or not close enough.

[@HealthyWayILive]

You twist until it aligns directly on it.

[@MzSweet21]

I have watched this video ten thousand times and still can’t get it.

[@HealthyWayILive]

Did you turn it side ways and slowly place it on there and twist?

[@brooklynthomas7607]

Make sure you don't have the gaskets mixed up. This was my issue. The top gasket was on the bottom and the bottom gasket on the top.

[@sanjobo]

make sure the gasket in the blender under the blades is right side up, the groove in the gasket must be facing up or you will not align. I was so frustrated that it wouldn't align I was ready to send it back but called Blend Jet and they informed me about the gasket, it lined right up on the first try.

[@dinahormigoso3049]

cannot turn the jar because the arrow is now aligned with the other arrow and its hard to turn

[@HealthyWayILive]

@@dinahormigoso3049 do you have the jar and base evenly?

[@gladysiti]

I’m wondering why my blendjet gasket doesn’t have the groove side? Its always hard for me to reassemble the parts after deep cleaning, its resulting the blendjet always leaking. One of the gasket is smaller than the other one, there is no groove side. And the smaller gasket is thicker than the other one 😢

[@sanjobo]

make sure the gasket in the blender under the blades is right side up, the groove in the gasket must be facing up or you will not align. I was so frustrated that it wouldn't align I was ready to send it back but called Blend Jet and they informed me about the gasket, it lined right up on the first try.

[@FreidaBoland]

Still cannot get it lined up…this is the second one I have had to return…

[@0524miracle]

I've been trying for 3 days and my arrows won't align. I'm not understanding the video. Need more details. Where to Start so when I twist the arrows will meet up and align.

[@HealthyWayILive]

Ok… put the jar evenly on the base, twist opposite directions until the arrows align and light blink white

[@joanvantine1387]

I have been working off and on all day trying to get my arrows aligned. watch the video about four times.

[@debraparrott8568]

Make sure rubber seal is in right. Grov

[@debraparrott8568]

Grooved side up

[@beccamahoney3990]

But mine is not tight if I line then up. It leaks.

[@HealthyWayILive]

@@beccamahoney3990 have to make sure that it is even before you begin to turn it. The light will blink red until you get it aligned and on there and then it will blink white

[@FreidaBoland]

Still can’t get it aligned.l.its dumb..

[@12234nic11234]

No matter what I do I can't get the arrows aligned,

[@HealthyWayILive]

Have to take your time and make sure the jar and base is even when twisting it together.

[@12234nic11234]

@@HealthyWayILive I finally got it, I thought I was going to break it twisting it so tight

[@HealthyWayILive]

Yaaay!!

[@Andr3y143]

still flashing red and align the arrows couple times hayz. Didn't work.

[@crystalmerriott8969]

Thank you, was about to throw mine out!

[@sanjobo]

make sure the gasket in the blender under the blades is right side up, the groove in the gasket must be facing up or you will not align. I was so frustrated that it wouldn't align I was ready to send it back but called Blend Jet and they informed me about the gasket, it lined right up on the first try.

[@vnatashalefi5122]

I still can't get it allign the arrow ... Already watched this video many times. So, frustrated. 😢😢

[@HealthyWayILive]

You have to make sure that it is even on there and then twist counter close wise.

[@vnatashalefi5122]

Thanks, is done.. I just need twist harder until allign the arrow 😅.

[@HealthyWayILive]

Awesome!!

[@maryellenjones1047]

Turn rubber gasket upside down so grooves face up. Finally worked

[@jollyroad18750]

Is your yellow blender jet 2 still working ?

[@HealthyWayILive]

Yes it was before I gave it away

[@infoplus9733]

no matter what I do my arrows will not match up and will not work

[@1love-1heart]

Blender jet is crappy,I just can't get it to align,not satisfied,sorry I bought it

[@HealthyWayILive]

Sorry for experience.

[@jones1394]

If you stip at the arrows it will leak everywhere

[@HealthyWayILive]

It will not leak if you have the arrows aligned and on evenly.

[@bahamaoy]

Thx it works great

[@FreidaBoland]

I flipped the seal still can’t align it..ridiculousness

[@HealthyWayILive]

Are you turning it counter clock wise? Making sure that it is on the base first before twisting it?

[@FreidaBoland]

@@HealthyWayILive well finally …the gasket was in the wrong way…that should not happen it should,leave the factory perfect…very disappointed...

[@FreidaBoland]

Seems it’s been a problem with many others ..

[@HealthyWayILive]

🤷🏽‍♀️I don’t work for BlendJet nor do I have anything to do with how it functions. I just help those with theirs like I’ve did with my own. Glad you got yours to align!❤️

[@etbough1]

fixed my problem

[@HealthyWayILive]

👌🏽awesome

[@DufresneCarole]

Je regrette cet achat, je n'y arrive pas ! et cette vidéo ne montre pas comment faire l'alignement...je tourne dans tous les sens et cela ne fonctionne pas pour moi.... 50 $ arnaque

[@charpecoraro7213]

Cannot get it aligned

[@HealthyWayILive]

Be sure to put it together evenly and turn counter clockwise wise… opposite from each other

[@shirleyhensford6412]

I have tried for hours and the arrows still do not align. This is extremely frustrating. I bought two blenders the one I bought for myself worked, but the one I purchased for a friend is not working. Please HELP!

[@HealthyWayILive]

Is their blender not aligning?

[@skque59]

There's gotta be a trick to align this. This video is not helpful.

[@HealthyWayILive]

It sure helped a whole lot of other people! Sorry it’s not working for you

[@skque59]

@@HealthyWayILive , no, the video should have given more tips like about the gasket...? SHould have said if you are having difficulty aligning it, check the gasket and maybe you want to flip it???

[@HealthyWayILive]

Thanks! Have a blessed day!!❤️