All Mower Deck Belt Issues Solved! Deck belt breaking or jumping off?

[@Rein_Ciarfella]

I can’t believe this. I just had a deck belt break yesterday on a customer’s lawn tractor! My first encounter with this issue! Timing is everything!

[@jayjudd6518]

This guy is so thorough on his inspections. 😊

[@ashleymarie7452]

Excellent video. Well organized, very relevant content. Well presented. Thanks!

[@Mechanical_Mind]

Thank you Ashley!

[@Ful-OGold]

I have an old husqvarna ride on mower and it’s a mechanical blade engagement type. Is there any way to tension the pulley that engages the v belt to spin the blades? Mine spins but once it gets and sort of load on it it loses cutting power and stops spinning. All bearings are fine and pulleys are fine.

[@nabilalhadi740]

Awesome video. Thanks buddy for providing a video that gets right to the point! Helped a ton.

[@Ziggle]

@Mechanical Mind Question: Can the belt wear out faster if I'm engaging the blades (tightening belt) while full throttle and riding mower is moving (I do this)? Instead, should I be stopped and have it at a slow idle, THEN engage belt, then speed idle to full? Or, does that even matter? Thank You in advance.

[@gail6904]

hello i can hardly push the engagement lever..it has too much tension and the clutch cable breaks it broke twice and the engagement handle is really really hard to push?? please help

[@Mike-jg1jq]

I had the issue of the belt coming off when disengaging the phone. It was the break pads were worn and letting the tension pulley get too close to the blade pulley. This put too much slack in the belt and it would jump off the pulley.

[@Mike-jg1jq]

Belt

[@mariocolon495]

Yes I have the same problem. Couldn't find this anywhere in the internet til I noticed it myself

[@arciefan]

What is the solution for this?

[@gstewart6778]

Did you add that bolt on the front top of the deck?

[@dempssa]

The cutting belt on my ride on keeps slipping, especially on lower mow setting. Oleo Mac mower. Any suggestions?

[@thedampestcrib6004]

Where on earth would I get the belt guide for the idler pulleys? I can't find them at all

[@mattcasdorph]

I had a belt chewed up on my Craftsman LT1000, found that one of the spindles bolts were loose and also worn so I decided to buy a rebuild kit and replaced both spindles, the idler and tensioner and rode it a few minutes and it got caught and shredded the belt. Turns out the belt got between the pulley and the little keeper piece that is supposed to keep the belt on the pulley. That wrecked my brand new belt that came with the kit. So I also found that the keeper was not in the right place when tightened. So that ate my old belt up and now waiting for a new belt to be delivered. This time Im going to tighten the belt without it running and watch if it is against anything its not supposed to be and then let off and see how loose it is. If worse comes to worse, I may have to fabricate some keepers to keep the belts from slipping off the spindles cause I took the plastic off cause of buildup on the deck.

[@crisprtalk6963]

I'm working pin a Deere D110 and it will just not key the belt on, all pulleys spin well, all keepers are in place, no grinding noises, no debris on deck, I am using OEM Deere belt, at this point I am about to give up.

[@danielbrothers1284]

You did a Great job... thanks so much...Jesus Bless You in Many Ways

[@mebonweb578]

Good video.

[@lkw5699]

Great video. Thx

[@JamesLyle-k3o]

Deck diagram for craftsman 19.5 riding mower

[@JamesLyle-k3o]

Deck belt replacement diagram turbo cooled lawnmower

[@JamesLyle-k3o]

Belt replacement

[@oysterace]

deck belt keeps twisting then breaking twice now

[@thedampestcrib6004]

Same I replaced all pulleys blades and now it does it faster I'm lost

[@JDMManitoba94]

Thank you so much

[@jonlambshead5115]

Great Video However I Personally Would Not Have Put That Deck Back On With Out Wire Brushing The Rust And Splashing A Bit Of Paint On It. Maybe That's Me, But It Wouldn't Have Taken Much To Be Thorough Plus Its Showing You Care About Other Peoples Stuff...