Combi Boiler Review | Viessmann Vitodens 100 v 050

[@glebetech6943]

An excellent unbiased review. I have fitted a lot Viessmann boilers and have very few problems with them. If a warranty call out is needed, in my area, the Viessmann engineers are very good. Cost wise Viessmann are comparable in cost to a Vaillant and probaly cheaper than a Worcester. I have never had any issues with plastic components in Viessmann in 16 years of fitting them. At the present time 12 year warranties are available too.

[@DADARI44]

Thanks Allen for the honest review - even when my German ears needed to tune in to your english for a while 😂 but very well done - very appreciated and we fully trust your experience.

[@AllenHart999]

Thank You

[@Heatable]

Brilliant video as usual Allen! Great to see the comparison of the two boilers.

[@AllenHart999]

Thank you for your support.

[@griffithsheating]

050 is an absolute steal. WiFi out the box, Stainless hex, weather comp, low modulation, opentherm, lambda pro. What more could you want?

[@AllenHart999]

What’s your opinion on the 100? Thanks.

[@luk5827]

@@AllenHart999 Vitodens 100-W B1KF , B1HF : How to enter to this parameter : Setting (%) in heating circuit 1 group: ■ Min. speed: Parameter 1102.0 ? And to increase minimal pump speed by Parameter 1102.0 .

[@steveduncan7637]

Hi Allen, very informative video. Had the 050 30 kw installed yesterday, very pleased with the product and no doubt I will choose Viessmann in the future .

[@kicam8744]

Great video.My vote goes for 100w. Can you record a video on how to commissioning boiler in different modes ... continuous operation, single room temperature control with ViCare thermostat etc ...

[@maxnavsa4470]

What I have learnt is boilers serve the same function, its the aftercare and service you get from the company when they breakdown that's important. Heard so much high end reviews about baxi so I pulled the trigger and went for it. The 3 boiler services I have had from them since has been a joke. One engineer done full service in less then 10 minutes and another engineer told My wife to clean the condensate trap and Magna clean her self by Learning from youtube. When I asked back - I have emails as proof. They said service only includes gas analyser checks. What a joke. Service costs me £170 a year.

[@penskib1975]

Thats shocking,I get rid of plumbers who think just a gas analyser check is a service,It's not! If I took my car in for a service and they charged me for a service and only checked the emissions then I wouldn't go back either.

[@TW-mp8zx]

So the actual service is essentially a routine point check on an annual basis to help maintain your boilers health and provide warranty cover and if needed those point checks may or may not need to be serviced.. the point of the analyser is to check the boiler is burning correctly and The engineer may need to adjust the gas valve or assess if the heat exchanger needs to be inspected, fan speed check will also indicate if certain points need to be inspected.. as a rule of thumb a service will be fairly standard for the first 7 years before assuming strong consideration for a strip down service, if you are specific on your own standard requirements for a boiler service then it would be best to check with the engineer before he starts what to expect from the service. But at the very least you should expect an engineer to be there for 30/45mins and this could end up as long as 3 hours or more.

[@Oleg85ful]

I love that prv is combined with condense discharge. No tundish no size upgrade like others

[@AllenHart999]

Thank You

[@kaichai9702]

100w or 050W is better suit for the 3-bedroom semi-detached with 1 bathroom? Will 100w performs better than 050W on the pressure drop issue while bathroom and kitchen sink are in use at the same time? Thank you.

[@igorj4493]

Hi, I have been watching your reviews for a good while. Top man some are very informative and helpful. I have just got viessmann 100w 30kw combi installed and spotted that the front panel doesn't have the foam inside like the one in your video. Does anyone know if all 100 should have it?

[@CrashUK28]

Allen Hart. Does the Viessmann 100w 2021 come with a weather compensation sensor in the box. I had one installed last year but I was not told it it had a sensor or not. But the Viessmann video on weather compensation said all boiler come with a sensor in the box?

[@sipepguru]

hi, did you get the answer to this?

[@johncast8756]

Excellent video Alan. The front cover on the 050 is not insulated so is there a major noise difference between the two boilers in a real world running condition?

[@AllenHart999]

Hi John. I wouldn’t expect a massive difference in noise but there will definitely be some.

[@sami_maran]

Any real comparison?

[@guillaumec.8787]

Hi Allen, Thanks a lot for your review, you are very clear and your explanations are always perfect. I might have a question, I am planning to get installation at my flat with the 050, because I like the size and the evacuation in the back. My question is, is it a problem if I use it only for hot water and not for heating? For the moment, I use electric heaters and I don't have enough money to change them. So am I taking a good choice with the 050-w and can it be use only for hot water? Sorry if my question looks naïve but no one can answer that around me. Take care

[@AllenHart999]

If you want radiators later, you should use a gas boiler.

[@guillaumec.8787]

Oh my god you are so quick to reply! Thanks again 😁 So I can use it only for hot water? It won’t have problem to work correctly?

[@ianewen6339]

Very helpful hints and reviews Alan . Your videos have helped us , decide on a new Viessmann 050 W boiler to replace our old Potterton unit.......thanks 👍

[@michaeldoherty7434]

Sounds like the 050 is a better buy as it's cheaper. Would the larger pump on the 100 be better for a 3 storey house?

[@dickiedubs3137]

I think the 100 is the better option looking at the data... but it's bigger so you need the space

[@Paul-gj9tx]

Have to disagree on the hoses Alan. I service/repair Viessmanns on a daily basis. I have been to systems that are as clean as a whistle yet the plates still blocked as a result of magnetite forming on and breaking off the rubber hoses. I have pictures of 1 inch shards I have removed from the left side hose (to big to pass through the main heat exchanger) formed perfectly in the shape of the inside of the hose, so I can be sure those shards did not come in it’s large form from the system. Any small metal particulars in the system, which all systems will have (you cannot remove 100%), appear to stick the hoses, and over time create larger pieces of magnetite.

[@AllenHart999]

Feel free to send me some videos and I would be happy to post your findings on my channel. Thanks

[@Paul-gj9tx]

I have no videos Alan, but have an interesting photo of what I got out of the hoses on a previous repair. Just looked at the photo and I was wrong, the shard is not 1” long, it’s more like 3”.

[@kevinrichards8586]

my viessmann 050 has now taking a longer time to heat the house to 21 degree and running the bath the water keeps going from hot to warm,

[@christopherwright1795]

Hi Allen , these combis look top quality and I’m thinking of replacing my system (thermal store cylinder and system boiler ) which is 20 yrs old , I have 2 bathrooms and a cloakroom, but we never use them at the same time , and the current system can’t cope with 2 hot water sources running , but I’ve been advised by 3 plumbers I have the best system and a combi won’t work , I hate the hot water system I have and I seem to be constantly suffering very cold showers , would these run a shower ??? And would it just be adequate or ok , my water input at the main is 20+ and hot water through the shower currently about 12-14litres per min , cheers

[@cabottaxi]

Just a quick question . 2 weeks time I'm due to have a 100 vitodens fitted in the kitchen. Can you tell me what clearance is needed to service the boiler to the sides of it ? New kitchen going in after it and I want to get an idea how near or far I can fit wall cabinets. Many thanks.

[@normanboyes4983]

As a follow on from Max Navsa and the subject of Servicing. It would be useful if manufactures specified a servicing regime akin to car manufacturers - like major and minor or on a hours run basis that specified which servicing operations should be done for each ‘flavour’ of service. This would enable homeowners to specify what level of service they required and for the heating engineer to be absolutely clear what he was pricing for and what work he was doing. The latest Viessman documentation is lacking in this regard. I do not like the condensate flex so far forward (it is also at the back on the 200 btw. The 200 has a minimum burner output of 1.9KW if I had a heat loss of 14KW on a -2 day - what advantage would I get range rating a 19KW system boiler (4 pipe) running on weather compensation?

[@AllenHart999]

Hi Norman. Just about to go to bed as I need to be up at 4.30 but do you really have 14kw heat loss?

[@normanboyes4983]

@@AllenHart999 Theoretically yes (calculates using web app) but I suspect (strongly) that empirically it will be less. The beauty of the 200 is it will tell me what my real heat loss is - all I need now is a minus 2c day - happy to wait for that.😉

[@JayL123]

Hi Allen, thanks a lot for all your wonderful videos. Which controls/thermostats would you suggest to go with Vitodens 100-w Combi, please?

[@kevinsimpson1884]

I have a 050 and ive a three bedroomed house and ive never been happy with it it just doesnt have the power to supply hot water to more than one tap. As soon as you turn on a second tap it takes all the power away from the first tap and if running a bath to get a lot of hot hot water i have to slow the bath tap to a trickle or its not hot enough. Im thinking of getting a 100 installed or getting my plumber to have a good look at my pipework in case that is to blame.

[@sunnyhong3688]

Thank you for the video. Compared to 050-w, will the 100-w use more gas to run?

[@davidbrown-yk9qq]

Is the 50 better if going in a cupboard in kitchen and I have 9 radiator s and 1 power shower over a bath ? From david Peterborough

[@leecav214]

how honest and up front.. always like and trust your you tube videos... simply honest and brilliant... well done Alan Hart.

[@stfuplsok]

*Allen

[@dennisdiep7144]

Hi Allen, thanks for your comparison on the two model. I am researching to find which boiler is suitable for my 2 bedroom ground flat with 1 bath and 1 shower and 91 sqm underfloor heating. My current boiler is a glowworm flexcom 24cx, the heat exchanger went after just over 7 years. It is demmed financially not viable by the plan company I have my boiler servied with. I have been looking at Worcester Greenstar 4000 30kw, Vaillant ecoTEC plus 825 and Viessman V050. Which one would you recommend? Thanks for your help in advance, Dennis

[@liborjelinek2070]

Hi, I think would go for wailant vaillant ecotec plus 24kw new version got 10l expansion vessel or WB 400025kw, only 6l expansion vessel, both of them can be range rared for required output, consider price of the parts for service,,good magnetic filters and lime descaler, your maitanance company probably didn't do any proper service that your boiler failed after 7 years, probobly ch system drained and then no inhibitor, don't like thermostat control of viessmann, I would say vaillant and WB is easier to control, , and guarantees

[@AllenHart999]

Thank You

[@critchley999]

Looking for instructions as to what the controls on the front of the boiler mean and how to use them. I've got hot water but no central heating.

[@Eric76]

Hi Allen, I have a 21 year old rear facing flue Vaillant 824E TurboMax plus in a studio flat, which I can no longer get a replacement flue for, and I am considering replacing that and 3 others for a Viessmann Vitodens model. Space is at a premium in 2 of the 3 flats, but can the 050 and 100 Vitodens boilers be adapted to have a rear facing flue construction on them or not? I received an email from Viessmann technical earlier today suggesting that: Our Boilers have a top mounted Flue Spigot, an Elbow is used onto this to turn the Flue to the Side or rear. However from their diagram I cannot see how this would make it a rear flue outlet. Please kindly advise me on that? Thank you.

[@AlexanderMonty]

Does the Vicare app allow you to setback the weather compensation? Heatable say no. Installers say yes . I need to find out if i can make as a minimum two setback periods oer day.

[@petermcdonagh6669]

Hi Allen is the prv and condensate combined. The modulation sounds great, does it work well with other opentherm controls. Thanks Allen top top videos👍

[@AllenHart999]

yes yes yes

[@AllenHart999]

i will wire a tado onto it and we will see what happens. Thanks.

[@martingill6996]

I have been to a failure of a plastic manifold on an older viessmann combi but the part was obsolete so couldn’t be fixed . Why would you choose the 100?

[@collectorsinfo]

Hi, we are looking into fitting a Viessmann Vitodens 050-w 25kw system boiler. We are on LPG. how is the boiler set up for LPG, because on our old Glow Worm 30cxi that now has a duff heat exchanger, we had to buy different gas jets. Thanks

[@katrinamorren8804]

I’m also unable to find anything online or in the manual about how to reset the boiler. Will switching it off reset it?

[@breadyegg]

Thanks for the review. I'm struggling to find reviews on the Viessman 100W B1GA range of Heat Only boilers? It's all combi combi combi! Can you point me in the right direction?

[@AllenHart999]

I will do one if i get chance. Thanks.

[@dickiedubs3137]

Thanks Allen, how do you get along with the touch controls on the front. I really struggled getting a fault cleared

[@AllenHart999]

Which model of boiler? Thanks.

[@dickiedubs3137]

@@AllenHart999 100 heat only. I find the controls very complex. Even resetting the boiler after lockout was tedious. From what I read you can link into the boiler with an App, can you do everything through the app including commissioning

[@dickiedubs3137]

I still don't get the difference between the 50 and the 100 other than dimensions. Is the 100w a 32kw input and the 50 a 29kw input

[@katrinamorren8804]

Hi, I have an issue with my 050 boiler (2 years old) heating schedule is off (via hive) but radiators still warm 24/7. This is only since either the really cold weather has came or I recall dropping the thermostat. I’ve reset the hive and reconnected it to the boiler. Any ideas?

[@mehere3013]

I need to change my boiler from regular to combi, 2 bed house , 1 shower, 6 radiators , whats best boiler to get

[@huyongquan6554]

I installed 222-F and 50 heat only, all has problem. The 222-F flue connector very easy be broken due to not centralised assembled in factory and has much stress. 50 condensation trap is nightmare for leakage from top of the trap. I see 100 has the same trap with old 50’s. Don’t know whether it will leak.

[@AllenHart999]

Thank you for the feedback. 222 is a standard flue connection and I have never personally had any issues with it. Did you do the 200 training with Viessmann?

[@AllenHart999]

It will be interesting to see if anyone else says anything about the traps as again I am not aware of any issues. Thanks.

[@D_UNKn]

Hi guys I need to replace my old Greenstar 28i, and I really like the VIESSMANN 050-W, do you have a rough idea of how much would installation be?

[@raygun1392]

Hi. would the 050 be reasonably quiet running ?

[@leightaylor5569]

Looking to change my old 100w have 1 circuit with rads upstairs and ufh downstairs not sure if 100 or 050 is the 1 to go for.

[@edc1569]

I thought the 100 was coming without the WiFi and display at the moment because of supply issues?

[@AllenHart999]

I haven’t heard of any issues.

[@petersteele46]

Hi Allen Would it be acceptable to put a sheet of foam or polystyrene on the cover of the 050 ? As the 100?

[@SalimKhan-gk1fh]

Hi Peter the self-adhesive sound insulating foam is available to buy to be cut to size and stuff on the front cover and yes it does make a difference to the sound of the boiler!

[@Jeffspiers]

Hi mate, great videos on the boilers. What is the actual difference in the 2 boilers. Is the 050 of a lesser performance ?

[@Eric76]

From what I have gathered, the 100 has a more advanced and larger display control panel to operate the boiler in a more self diagnostic manner amongst other things. The insides of both are the same, except the depth of the 050 is 60mm less than the 100 at 360mm deep.

[@dickiedubs3137]

How do you get to the condensate trap on the 50

[@anthonygordon7356]

hi Alan, i have toe 100-w with the black glass front wireless, how do i turn on the back light please

[@IosifViorelMila]

It would be really nice if you could showcase how to wire viessmann 100openthermtado wireless receiver. I've read that Viessmann has some kind of KM-Bus interface. Is this compatibile with opentherm ? Thanks!

[@AllenHart999]

Hi losif-viorel, I will look at doing some of these for you as soon as possible. Thanks for the feedback.

[@AllenHart999]

Just got a tado today. i will try and do a video soon. Thanks.

[@IosifViorelMila]

@@AllenHart999 Thank you! You’re very kind 👏

[@jampam-jf8mt]

Can I control everything on these boilers without WiFi or do they have to be connected to WiFi?

[@mylifeintheuk2093]

Hello viessmann 050-w 25kw combi boiler Or Baxi800 25W I’m confused in choosing the one between these two 😢

[@AllenHart999]

What did you go for? Thanks.

[@mylifeintheuk2093]

@@AllenHart999 Continuing with the existing one for another year or so. Got Google Nest to have control over heating & hot water.

[@richardhodgson7443]

Looking great Allen, be good if you can do a strip down on both boilers at some time mate please

[@AllenHart999]

You can come and strip them down if you like buddy 😂 But yes I will do a video on them. Thanks

[@richardhodgson7443]

@@AllenHart999 now that’s an idea 😁

[@AllenHart999]

@@richardhodgson7443 Let me know if you fancy a road trip.

[@richardhodgson7443]

@@AllenHart999 will do buddy

[@dougbamford1810]

Thanks Allen!

[@ijs6962]

How do I increase the signal on the communications module ? from low to higher ?

[@andybanov4319]

Which connection do you use for hive on 100 30kw combi is there a link to take out ?

[@scotthawkins5347]

Hi Alan I wish you worked near me in Surrey you are a diamond ! I'm getting on one of these soon is there a way I can check if the engineer has set up the weather monitoring and what does this actually do ?

[@AllenHart999]

Check out Heatable bit.ly/45wY7Qu

[@scotthawkins5347]

I've already booked iheat as had a deal on a free hive , I just am not sure what the open therm is and how I will check they do this

[@AllenHart999]

@@scotthawkins5347 Hive is terrible, i wouldn't personally have one given. It's a basic on/off control.

[@scotthawkins5347]

Hi Alan I'm.looking to make my viesmann 050 30kwh as cost effective as possible , I know the weather comp is avaliable with hive but I think nest can use open therm problem is they are including a hive free of charge , should I go buy a nest and get that fitted , I simply want to out my best jockies on best horses if you know what I mean !, its a minefield if you're not used to whats avaliable. Any advise is helpful thanks for your great videos

[@stfuplsok]

@@scotthawkins5347 *jockeys

[@LabRat6619]

I went with the 100 system because of one of your old videos. Other things encouraged me. The size, the origin, flexible flue (for class 1 chimney). Things I didn't like was the low voltage side on the DHW, needing another part to make it work with my unvented.. Also parts are expensive.

[@AllenHart999]

Thank you for the feedback. Make sure it gets serviced correctly and it will last you for years. Thanks.

[@coffeehead68]

I wouldn't bank on that, mine has packed up after 22 months, a viesmann engineer has been out twice this week, apparently he has now replaced all the parts today and this evening, it is not working again. He tried to tell me that it is bad gas (I am on LPG), never heard anything so ridiculous or insulting.@@AllenHart999

[@jameshawkins5280]

Great video Let's have some videos on the new regs as of June 1st on which boilers do modulate down to 3-4 kw name and shame allen 😉

[@AllenHart999]

kzbin.info/www/bejne/ooa8i3euqclmsJI

[@kevinrichards8586]

how do i remove air from the boiler it self Viessmann 050

[@julianwebb8712]

I’m confused that their website describes the 050 as a Combi and System boiler…….is it available in 2 versions ?

[@markdauncey927]

They run DHW as a separate circuit in the system boiler like a combi. That's how they can offer full weather compensation.

[@ChiefBrianIrons]

I was going to go with Viessmann but plumber told me don't go with Viessmann. He recommended me to go with intergas as he would install both. He told out every ten Viessmann boilers he installed two would have issues. He told me never had issues with intergas now he only installs intergass boiler's. Hey Alan I wondering if you can give me some advice. Would it be safe to use Aluminium radiator within existing 20 year old system with all steel radiators. I heard it bad to introduce new metal to old system. Any ideas would it be safe

[@AllenHart999]

as long as you look after it and have it serviced correctly i am sure it will be ok. Ask your installer if he strips the boiler and cleans it, also ask if they change the seals. Thanks.

[@petersteele46]

Thanks Allen for a simple clear video. Just ordered an 050 on the strength of it. Can a Google Nest be connected to the 050 to control the hot water and heating?

[@spoonz1065]

Did u ever find this out? I want to be able to connect my nest thermostat to it

[@Leonards-leopard]

@@spoonz1065 you can connect a google nest to pretty much any gas combi boiler

[@ChipZilla69]

@@spoonz1065 I just got quoted on the 50 and was given the option of a nest or a hive. I'm going wit the Hive but I think you can use either based on what the guy told me.

[@stfuplsok]

a* 050

[@SafarWIP]

do you offer installation of these?

[@giuseppesprovieri416]

Ciao!Noi ne abbiamo installato diverse e devo dire che è un ottimo prodotto!

[@AllenHart999]

Grazie mille per il tuo feedback. Hai mai avuto problemi con i tubi di gomma che si bloccano.

[@giuseppesprovieri416]

@@AllenHart999 Purtroppo si. Sia sulla VITODENS 100-W che sulla VITODENS 050. La cosa strana è che era presente su entrambe le caldaie il filtro defangatore ed il SENTINEL X100, oltre ad avere lavato l'impianto termico con il SENTINEL X800.

[@jockster5525]

Great video.thanks for your efforts and sharing your experience. 👍👃👍

[@AllenHart999]

Thank you.

[@andyla44]

The viessmann 050 is WiFi ready do I need the tado or hive thermostat to make it work with viessmann phone app

[@Eric76]

The more compatible one is the TADO from Germany, but it should in theory work with any smart thermostat.

[@stevetustin6838]

I have a 8 year old 050 which I think is on the way out. Is the new 050 a straight swap i.e. use all the existing pipework etc. Many thanks

[@stfuplsok]

an* 8 year

[@ram64man]

honestly I would never buy a viessmann again, I had an old gen 100w regular and found the build quality was really lacking against the neighbours combi, almost as if it hadn't been updated at all to keep with time it was very similar to the 050 with lack of sound proofing , rubber hoses always the condensate was clogging. the noise was quite loud as well. and call out and parts were expensive, gas seals took forever to arrive as well. in the end we swapped out to an intergas HRE, built like a tank, granted it needed to have a water softer fitted but the rest 4 years zero problems and was still knocking it out the park when I moved home. parts were a little slow arriving, but far better than Viessmann, 6 week for anything.

[@AllenHart999]

Hi ram64man. Thank you for your feedback. Do you think some of your experience could be down to the people who installed the boiler? Thanks.

[@ram64man]

@@AllenHart999 he retired so won't bring up his name as he did nothing wrong. services and repairs by a c series - Andrew who was really good at what he did but was super booked , but when we had enough following a heat seal failure and long 6 week wait for parts. updated to intergas we turned to HD Plumbing & Heating who were the only intergas installer in area. who did a great job, my late partner was there when it was installed due to an accident at the time i was in hospital so don't know who actually did the install with the team. services have been done by a semi local Plummer since, by CGo Plumbing & electrical Ltd who again were excellent

[@debbierideout6162]

JUST HAD THE 100 INSTALLED THIS WEEK WATCHED THIS TO GET MY HEAD AROUND THE TEMP ALTERATIONS. BLOODY TECHNOLOGY AND OLD AGE DOESNT WORK 😂

[@darkodarko3042]

Vitodense 050 - what does mean white blink lamp? Anybody?

[@AllenHart999]

Thanks very much for your comment, please consider subscribing to support the channel 🙂

[@DrExpresso]

Great vid, thanks

[@36kingsman76]

Hi Allen, we have got a 111-W storage combi installed, single circuit heating. Commissioned, no fault code. But the heating is on and we set to 60 degree. The boiler will running and heating the flow temperature up to 90 degree and stopped. And cool down then start again to 90 degree. Their is 345 fault code under b.4. Any idea what is going wrong?

[@stfuplsok]

There* is

[@RobB-rj5vn]

Hi I've just had fitted a viessmann 100 fitted. My water pressure is very low 4.5 liters a minute cold when it comes to hot water it's now down to a liter a minute. Been on to technical and they say it's dew to the plates in the heat exchanger I am lucky to get any with that flow rate. My main is shared with 6 other properties. Do you think a booster pump would help if so any suggestions thanks in advance and look forward to your reply

[@stfuplsok]

*due

[@markdauncey927]

Too late now but you'd be better off with stored hot water.

[@stfuplsok]

You'd need a booster pump.

[@anthonygreenwood4486]

I’ve found Viessman customer service and getting hold of parts a nightmare These boilers are for the Uk market only Without the infrastructure for Uk fitters Get yourself an ideal

[@AllenHart999]

You can generally get parts if you know where to go. Thanks.

[@ozwellalford5015]

I personally rate viessmann as the best boilers there are not complecated on services and easy to understand.

[@stfuplsok]

*they

[@abvoyager333]

as a customer looking for a boiler and a heat loss of 8Kw why buy a 30KW boiler. What would be the optimum size?

[@jmb69er]

hot water is the main reason you need more Kw

[@sipepguru]

Baxi 836 vs Viessmann Vitodens 100w??

[@AllenHart999]

Viessmann

[@sipepguru]

@@AllenHart999 Hi Allen. Thanks for the reply. What is your main reason for picking Viessmann out of the two?

[@spoonz1065]

Are you able to install a nest thermostat to the 100?

[@AllenHart999]

Yes

[@spoonz1065]

@@AllenHart999 thanks . Is it as simple to do as a normal combi boiler . Simple on/off and let the nest do the brain work ? I have 3 lodges 2 that have nest fitted and this one is for the new one . So want it all on the same app and will update the old boilers later on down the down to the same if it's a good boiler . Was thinking the 100 or a baxi . What would u choose ?

[@alanmelton4885]

Which country are they made in and how expensive are parts compared to other boilers ???

[@Eric76]

The 050 is assembled in Turkey and the 100 is assembled in Germany.

[@louisesaayman4467]

good video. thank you

[@abusara4787]

Free 10 years warranty is still on?

[@AllenHart999]

i am not sure. if you log on the website it will tell you. Thanks.

[@ChipZilla69]

Yes, I just got quoted on the 50 and it comes with 10 year manufacturer warenty.

[@stfuplsok]

@@ChipZilla69 *warranty

[@brianmcdonald80]

How many time can you say the word boilers 😂

[@AllenHart999]

Boiler

[@brianmcdonald80]

@@AllenHart999 just fitted one of these on opentherm nice boiler to install but the instructions are not very clear.

[@markblackburn969]

Worcester every time installer friendly busman 2 days to commission nightmare plus side light to put on wall that is it 😂😂

[@philiphowles467]

Not impressed with Viesmann at all. Our boiler has packed up after being installed from new 18 months ago. Have tried to contact and they have attempted to charge me £350 to call out/repair, without even knowing what the issue is. Avoid at all costs!

[@AllenHart999]

Whats the issue with the boiler? Thanks.

[@gah9186]

Sorry but that was a very lazy review I had an 050 installed in June 2022. Four engineer visits… 142 error, fan fault, I get the impression from the engineer…a common problem. Controlled by a Google nest using Opentherm. Dislikes, can’t disable hot water preheat, CH Opentherm preheat, can disable overnight, but not mid day. A week between fault and fix. Vicarage app low on features.

[@AllenHart999]

Send me your review on video and I will upload it on my channel 👍

[@MrRawMonkey]

Buy British, as there are enough quality U.K. built boilers.

[@AllenHart999]

Which boiler is British ?

[@stfuplsok]

@@AllenHart999 Vaillant, Ideal, etc.