How to fix an EGO Mower that won't start

[@kathyselvaggio2229]

This was very, very helpful for a not-very-handy 67-year-old who is tired of paying repair people. I got through about 11 minutes and I was able to resolve my problem with the mower not working. I hope to remember to return to this, if I have trouble again.

[@allyourtechai]

So glad it helped!

[@JETBOARDKEVIN]

Fantastic! What a time saver in troubleshooting my mower. I put it away running, three weeks later (California) go to mow and nothing! I went straight to the wires in that folding handle elbow and sure enough, in the smaller wiring harness I found the red wire almost cut in half. The insulation around the three wires is shrunk to fit and difficult to strip back so be careful not to damage the other wires. I made the repair and tried to route the wires in a more non-abrasive manner, even coating the area with silicon past to reduce the folding friction. I took some photos, but guess you can't add them in the comments. Thanks so much for the video.

[@allyourtechai]

So happy to hear that this helped! Cheers

[@LauranceNashLaurie]

Thank you from Australia, my EGO LM2000E was doing the same thing. I pulled mine apart, made it do the same fault, dismantled the micro switch put a small squirt of WD40 in the switch and reassembled it. It never faulted in a short test but if it does it again I know what to look for, thank you very much for dismantling your mower to show us what to look for.😁

[@allyourtechai]

Glad it worked out!

[@gaylem3935]

Wow! I can't thank you enough! As another 67 year old, I came so close to loading my mower up and bringing it to the repair shop. I was doing my last mow of the season and my mower just stopped. I checked the battery, took my air compressor and blew it all off (not sure if that did anything, but ???) I even called 2 repair shops. Then I remembered how helpful KZbin is and low and behold your video showed up. It was the HANDLES! I unlocked them and slid them up and down a bit, then locked back into place and WOLLLAAAA!!! It worked. Finished up my yard, cleaned it all up and going to the garden shed until next spring. Again, THANK you for doing this video!

[@allyourtechai]

That is fantastic to hear, so glad it turned out to be an easy fix :)

[@modelmartin]

I was pulling my mower backwards and the handle hit my neighbor's retaining wall and it shut off. I just pulled the handle back out all the way. Voila, it worked.

[@markboone872]

Thank you. Thank you. Thank you. You were spot on in identifying the wire problem. It was a tricky identifying the bad wire. When I moved the wire that left a three wire connector the motor would stop or start. I had to strip the sheath holding the three wires, (Red, Blue & Black. ) and separate them and move them individually until I identified a break in a 2 inch area of the black wire very near where you had your problem. There was no sign of damage to the insulation. I spliced a piece of wire in its place and secured it with wire nuts as I did not have a soldering iron. I think it should hold a long time and the mower now starts reliably. I'll buy you an adult beverage of your choice if I'm lucky enough to meet you in person.

[@blogachickhedricks8730]

Thank you so much! Mower died. Couldn’t find anyone to fix it. (Buy a new mower, they said). Lawn turning into a hay field. Oh, what to do? And then I found you. I bypassed the relay (under the hood) and, Eureka! the mower lives again. Only mystery is the spring and small plastic part that fell out when I took off the cover on the side rail to check that relay. (I couldn’t figure out how to fit them back in). Sure wish I knew what they did but, oh well, the mower runs just fine without them. So, thank you again. You’ve made me one happy, empowered 76-year-old lady.

[@josieedmisten8908]

Thanks so much. While close ups would have been helpful, I'm thrilled that after following your first couple steps my lawn mower was running again. I've told my kids not to store it with the handle folded over anymore as well because I don't want the cords in the lower arm area to fray as u described. That's a great tip to prolong the Longevity of the mower wires. I'd gone to a repair shop this morning to find they only repair gas. Thays when I searched for a troubleshooting vid. U saved the day. THANKS AGAIN.

[@Kathy-ie9lt]

I've had my mower for 5 years now. Last time I started it, it started with no problem and I took a few steps and then it stopped. I started it again, took a few steps, and it stopped again. Then it wouldn't start at all. I made sure the battery was seated correctly, that didn't help. The light on top the battery was green. But since I couldn't figure out what was wrong I put it on the charger . It went thru the charging, I took it and put it back in the mower, it didn't start. This time I noticed that the yellow light on the mower would blink and then shut off. I just wanted to say that I was so close to paying out 300 bucks for a new battery before I watched your video. In your video when you did the part about the handle , it made me remember that a couple years ago my mower wouldn't start and it was because the handle clip was not on tight on one side. So I just went back outside and sure enough one side wasn't clipped on tight. I fixed that and mowed my lawn. So sometimes it's the simplest things that can be causing the problem. And your video helped me get mowing again. Thank you !

[@jnellie1970]

Really liked how well you explained each problem, then each potential problem, then how to resolve each of the problems! Awesome. Thank you.

[@allyourtechai]

Glad it was helpful!

[@jamesmiller3708]

This video helped me find the issue with my mower. The handle angle relay was jammed - after a quick vacuum and re-seating, it's working again. Thank you so much!

[@HH42]

Thank you so much! You helped me fix my problem in just a few minutes. One of the green center clips had caught on something and came unsnapped mid-mow and I didn't even notice. I never realized they needed to be fully extended so the mower would run. You are awesome! Thanks again!

[@Rodzilla-wi1yu]

Thank you, you saved me a lot of time and money. It turned out to be the relay and not the battery.

[@robertsmart5600]

Brilliant, I've got the same Ego mower, some pandanus fronds got wrapped around the blades so I took the battery out to unwind them and then the mower would not start. I pulled the handle right out & reseated the handle clips and it worked fine, you saved my day :)

[@allyourtechai]

So happy to hear it was helpful!

[@daveuhlig1413]

Thank you from a 72 year old man the did almost hit the panic button until I found your very helpful video!!

[@davidblask6710]

I panicked this afternoon when the mower wouldn't start. I knew the battery was fine. Luckily I found this video right away and was reminded if the handle isn't fully extended the power won't flow. Sure enough, I had forgotten to secure one side of the middle of the handle and it started right up. Excellent video - many thanks!

[@billkoch2351]

I just finished mowing the 2nd half of the lawn. Found, and fixed, the tiny broken wire just like in the video. Thanks!

[@MC-pg2ko]

Thank you for your video. A close-up view of how you were doing the repairs would have been very helpful. Looks to me like pinched wires are a design flaw, as it happens when the mower is folded for storage. This issue will be costly to fix after the warranty runs out unless the mower is stored without folding the handles, which defeats the purpose of buying a "compact mower" to save on space!

[@kevinholcomb8015]

Thank you. That helped immensely

[@jimjohnson2987]

👍👍the middle relay was my problem. one clip not closed when closed it started. back to work wife!

[@mal335588]

A very helpful video. Shows what to look at next when you've checked all the more obvious possibilities.

[@allyourtechai]

Glad you found it helpful!

[@davidkeating8751]

Sir - Your issue mirrored mine - a pinched wired when the handles are not fully extended. Not sure if this is a feature or a bug, but regardless, it is something us EGO mower owners need to be aware of . Thanks so much for taking the time & effort to create this video.

[@carlab.zimmerman1779]

I am impressed by his knowledge and ability to explain the issues in terms I can understand. Not sure I'll try the rewiring part myself, but really good to know where/why my mower broke. I do think that if he is going to be barefoot while demonstrating with a mower blade rotating that he should at least have a comment "shoes recommended while working around rotating blades" or something about safety! haha!

[@robertlambke8260]

Thank you for posting this video! It saved me a bunch of headaches as I had no idea about the really in the middle of the handle. It turned out my handle latch hadn’t closed all the way. Problem solved!

[@AbFlwrs]

Thanks for you video man, you saved me to buy another.

[@4Tugboats]

Thanks so much for your video. I have not tried to repair my EGO 56 Volt mower yet, but I am very handy where things like this are involved. I have never found anything I couldn't do yet. There are many things I can't do, but I just haven't found it yet.

[@xiiirob]

Nice vid! Mine stopped working, but the handle made the green light go on the battery, so I knew it wasn't a connection issue. Turns out one of those green tabs in the middle of the push bar was open, guess that breaks the circuit!

[@tonymri]

Simple and easy to do. My handles were not all the way extended then clipped on. Its brand new and first day of using it and these simp[le electrical checks worked for me. I thank you for making this video.

[@tndude278]

Informative video. I had the no start problem. Didn’t realize there was the handle relay (#2 in the video). Went back out to check and found the handle had come unlatched causing the relay side to slide in slightly. Pulled handle out and relatched. Problem solved. Thanks!

[@jk-qf3lt]

Big help.... Pinched wire here as well, mower is running again. thank you!

[@joellee9750]

Thank you! Mine stopped working this week. I just fixed it today. It had the same exact problem.

[@mljones38]

Thanks for your calm demeanor. It cooled me down and almost the first thing you said put me on the correct track. Push the start button before pulling back the lever🤣. I was doing the opposite. Hey, it’s the first cut this spring.

[@charliewrites]

wow..i just took the mower out for it's first spin and didn't have the handles extended and i watched this , and BOOM! it worked thanks..

[@allyourtechai]

Awesome! Happy mowing!

[@joeb4568]

One of my side rails was opened and slightly lowered! That was it! Fixed! Thank you

[@allyourtechai]

Glad it helped!

[@jimsparks-pw9tq]

Thank you Al. I wish I had seen this prior to disposing of my first one. Now second one doing same thing. I will investigate issue using your advice.

[@jimsparks-pw9tq]

You are 100% correct Al. It was the exact issue that you had. Thank you.

[@davethedogification]

Great video. This happened to me when I went to use mine for only the second time. Luckily Lowe’s did an even exchange for a new one. I will keep this video in mind going forward. I wonder if anything can be done by us owners to 11:19 prevent this from hhappening

[@mandatorym_y_o_c_a_r_d_i_t_i_s]

I just got my mower out of storage and it won't start. I'll look for the relay under the cover and post if I can fix it. Thanks for the timely video.

[@robjones8950]

Thanks for this. I fixed mine with your help.

[@tracylogan9990]

Thanks for the video. This (the wiring in the arm flex) is exactly what is wrong with my new ego mower. I’m just worried about working with wires.

[@kendrickking5479]

Thanks!

[@jnellie1970]

Thank you! Had it figured out in 5 mins.

[@jamescameron8612]

I had the problem of the blade not starting to spin (self propelled always worked no matter what). Finally, I tried releasing the clips on the handle, pushing it all the way down into the portion of the handle attached to the mower, then pulled it all the way back out and locked it. Doing this fixed the problem and it starts every single time (when you do those steps each time). I'm going to guess that Ego thinks everyone is going to fold up and hang their lawnmower on the wall. I have no interest in that and simply roll it in and store it like I did my gas mower. I will say this stupid problem and an extremely expensive lawnmower was a huge disappointment, but thankfully the solution was as stupid as the problem they created. This is why I'm hesitant to buy much of anything anymore. No matter how much you pay for it (never buy the cheapest stuff, always at least mid level prices) the products produced now never seem to NOT disappoint! I hope this helps some of you.

[@riversrwet]

Boom. Super helpful. 1 second fix!

[@richardnash6613]

Thanks for your informative video. I have had bad switches in the arms/handles and the lower pivot point where you jumper around this permissive switch. I love my EGO mowers(all 3) but they have had some issues with the safety switches....so thanks very much for the video.

[@allyourtechai]

Glad it helped!

[@maryfiorillo4871]

So helpful! We got it to work with your help. Thank you!!!

[@tln8424]

Your video was very helpful. My ego runs fine, but the self-propelled functional won’t work. I am guessing I need to go through the same testing procedure that you did for the starte problem unless you have any thoughts

[@Samvargas-j6x]

Thank you I was able to fixed my POS lawnmower thanks to you 😅

[@kendrickking5479]

Thanks so much! I didn't have the handle extended enough

[@mcmanamen33]

Exactly what was wrong with my Ego. Thank you!

[@Phony-baloney8]

Cool. So I just have to utilize my electrical engineering degree to fix poorly designed, easily anticipated electrical wiring problems with my Ego mower. I’m not saying these kinds of mowers need to be perfect, but it’s a little annoying when something like this ‘breaks’ when it could have been easily avoided if it was designed a little better. Great job, Ego.

[@brandonulstad]

thanks for this video. just helped me fix my mower!

[@allyourtechai]

Glad I could help!

[@JPW050]

I have a newer EGO mower (2135SP). The mower blades would randomly stop while using the mower. It seemed that the slightest movement of the handle would cause the safety switch to stop the blades. In most cases, I could restart the mower by pulling up on the handle and starting the mower normally. Finally, I became annoyed with having to do this. With the newer models, the configuration of the safety switch is different. There is no spring. I opened the plastic components on the handle which houses the safety switch. There are several TORX screws holding the components together, so an appropriately sized TORX screwdriver is needed. The switch is configured as a Normally Closed (NC) switch. When the handle is not in the fully up position, the switch opens, and the blades stop. I first thought of removing the switch and permanently connecting the two wires together. I then opted for another solution in case I wanted to easily remove my modification. The switch has an unused Normally Open (NO) terminal. I used a small piece of wire to connect the NC and the NO terminals together. This basically causes the switch to have no function. I reassembled the mower and now everything works great without interruptions. Of course this removes one of the safety components of the mower. Be aware that the handle will not have to be fully extended to start the blades. I enjoy all the EGO mower videos on KZbin. I only wish more videos for the newer models were available.

[@edfluencemedia]

How do you get to the third switch? What type of screw driver? I can’t seem to get in.

[@allyourtechai]

Oh boy, I don’t remember off hand and my mower is 5000 miles away. It might have been a star wrench if a Phillips head doesn’t work

[@VioletDeliriums]

Yo yo wutup B-Lev...WOOOOH! The relay in that doesn't work when the handle is not fully extended was my problem. As Darth Vader might say, "All too easy." Thank you!

[@allyourtechai]

Glad it was an easy one! Cheers!

[@BonkersGameplay]

My issue was pretty similar to yours but ended up being where the wire that runs down the arms connected to, the connector had a loose wire so I put it back in there and hot glued it. It's amazing how crappy these things are for 800 bucks. should've got a commercial gas mower.

[@keepinganonymous3631]

This happened to me and I'm not an electrician. Not mentioned in this video is the bottom was completely bogged down with compounded grass. Spent a good 30 minutes cleaning it (NO BATTERY INSTALLED) and it started right up.

[@allyourtechai]

Good tip!!!

[@zozzrc]

Thanks for the pointers, very helpful. To others coming across this video I want to say this mower is no way worth the money. Besides this problem I've had to buy a second battery after only using the first battery for one season. Besides not lasting for my 15000 sq foot lawn it also stops pushing the grass into the bag well before it actually stops so you end up with droppings on the lawn. This means you have to switch out the battery even before it actually is out of charge. I'm sorry I bought this mower and would not recommend it to anyone. Assuming it makes it through the summer, I'm done with EGO and will sadly go back to a gas mower next year.

[@CrazyLinguiniLegs]

Well, it could be worth the price for some folks. Just to offer a contrasting experience: I have used my ego 21” mower for 7 seasons now, I’m still on the original battery, and have not needed to make any repairs or replacements. My lawn is only about half the size of yours, and I cut it all on a single charge.

[@BuckeyeNutUG]

Sorry you had a bad experience with the battery. A friend told me to store my battery in a cool place (the air conditioned house) rather than in the garage which seems to help with battery life. And to bring it into the house in really cold weather (winter) so that the battery doesn't experience temperature extremes

[@CrazyLinguiniLegs]

@@BuckeyeNutUG yep, after the last fall mow I charge the battery and bring it into the house until next spring.

[@frommatorav1]

I will have to disagree with this. Your battery is under warranty for longer than a year, for one thing. In my opinion it's nice to have two batteries though. I use the grass catcher every time and when it gets close to full, you have to empty it or it will act like a mulcher instead. My mower cuts the lawn as well as a gas mower and I haven't had to do any maintenance. I've had my Ego mower for 8 years and my 5ah battery stopped working as well in year 5. I bought an Ego 16" chainsaw with a 5ah battery, 3 years ago and use that newer battery in my mower instead. It is an upgraded battery over my original, but the og battery still works as a back up to finish my lawn, while I put the other one on the charger. I have used the newer battery for 3 years and it still works really well. I've been keeping my batteries in my garage or shed, which do get hot and cold but are dry (but humid in summer) and shaded. I know batteries are expensive, so I would recommend getting one with another tool, like a blower or a chainsaw.

[@assortedmountainlife]

I've been using mine for 3 years now to cut 4 acres of meadow and it's great other than the fact that it now doesn't start. No complaints at all on the cutting ability though.

[@janeiztheone]

Man you're the best!!! You saved me. Thanks

[@allyourtechai]

That’s awesome, so glad to hear it helped!

[@maxj0930]

I will now check the relay/wire harness in the base. Thanks!

[@marvelousjoe]

Thanks for sharing this video. This helps us all

[@allyourtechai]

Glad it was helpful!

[@Pokerpimp1919]

Did you ever make the video about removing the spring ? I could not find one

[@btomas225]

edit July 5: I disassembled my 2130SP (brushless mower) today and confirmed what I wrote below. There are NO relays in either the 2100 (in this video) or my model, the 2130. There are only lever operated micro-switches (more like mini), one used in the telescoping handle, and one in the upper handle (pushbutton and swing bar) and one used in the power body attached to the lower handle such that when the handle is stowed in the full forward position it engages preventing the mower from starting accidentally. So there's 3 total switches used and no relays. All are used for purposes of implementing "safety" interlock modes. July 3: Umm, good video, however what you term "relays" are actually called "interlock switches" or simply interlocks in short form. I am an EE and we use interlocks in electrical engineering for numerous things. I have not taken mine apart yet but am looking at various videos to lessen the hassle but these minor things caught my attention.

[@allyourtechai]

Yes, appreciate the correction.

[@LauraMLBearl]

Thank you for this video. It was very helpful.

[@MustangHully]

Thanks for the great video. One question. Can you show how to put the cover back on. It came off easily. Its not going back on :(.

[@anthonykent8561]

Folding relay may not be seated and in your way.

[@noesantana_com]

Thanks for taking the time to post this vid, it got me back up and running with little effort. Call EGO and of course I never registered my machine and they wanted the original numbers to the battery that came with the unit that I no longer had. Wow, it's customer service until it's not. You have a new happy subscriber, can't wait to see your other vids to see what all you can help others with.

[@TheGadgetwiz]

Interesting video. Are those relays or switches? There is not much difference. A switch makes a connection when it's pressed (2 or 3 wires). A relay makes a connection when an electrical voltage is supplied (usually 4 or more wires). Both physically move a connector, but the relay typically uses a coil to create a magnet, and that magnet moves the internal connector.

[@allyourtechai]

I believe they are actually switches. I unfortunately kept calling them relays, but you are right.

[@jaredlee9384]

Really enjoy seeing your process, thank you for uploading! I have an ego mower that will try to spin upon starting, but won't fully start. Where would you start in the troubleshooting process? I just uploaded a video of what im experiencing in case you or anyone else might be able to assist. Thank you!

[@MatadorSaga64]

Mine is the 2nd relay. i have to fidget around with the extension for it to kick on and off.

[@xDIGITONIUMx]

Mine was from a small switch at the bottom of the lever that wasn't getting depressed when clicking it into position. Held in a plastic housing that warps over time causing slop.

[@jimcochran1128]

That’s all well and good, my problem is getting the cover off. What kind screws, Phillips head or some kind of weird screw I don’t have screw driver for. The screws are so deep set I can’t see the head. I hate this mower!!!!

[@Edward-Norton]

What you call a relay is actually a switch. A relay is electrically actuated and makes or breaks a contact or set of contacts. A switch is mechanically actuated and makes or breaks a contact or a set of contacts.

[@allyourtechai]

Haha, I know, and I said it so many times in that video.

[@surenadhikari8480]

This is helped for me. Thank you

[@Donoltmann]

Great video! Had EXACTLY the same failure.

[@Donoltmann]

These are really great mowers.

[@MrNomad505]

Thank you. got my problem solved.

[@steaminglobster]

Some big bone stuck under it, so it did not start with yellow light blinking. After removed the big bone, my Ego works now hoping this info helps other people.

[@jermainehynson7514]

What type of screws did you remove to take off the cover (hex or phillips)? Does it require a specific tool/bit/extension?

[@shereeblume9353]

Thank you for your video, it helped, I just didnt pull my handle bar out far enough, Im saving your video just incase another problem comes. Thanks again.

[@allyourtechai]

Glad it helped

[@kampferbigo]

Great video, thanks

[@allyourtechai]

Glad you liked it!

[@teressasutton8295]

Oh goodness I cannot wait till daylight I have got to try this I have a feeling it might be that relay

[@codyrobinson5612]

This helped me thank you!

[@kneelingcatholic]

Boom!! My blade only engages when I hold the handle in the 12 o'clock position. makes me look like a dork when I am mowing!! That relay or wires must be the problem. THANKS

[@SaulGood365]

great video..its working now!

[@stevesmith6819]

Thanks for the informative video. Can someone save me some/frustration with my Ego LM1700E-SP mower, please? Seems to be similar to the one in this video. It was working fine - last used a couple of weeks ago. The battery is fully charged but the blade motor does not operate this morning. The battery and the mower green lights show on, but the motor fails to spin. However the machine drives forward as normal. I have tried it several times, checking the handles are fully extended etc. Where should I look next? As I say, it’s only the blade motor that’s failing to work and I wonder if that suggests where I need to look first. The blade spins very freely when rotated by hand.

[@luisguevara2049]

Thanks so much for your help 🙏

[@jawaring4367]

Can you please answer a question for me? I am getting 27 volts on the main start relay at the top of the handle, should all 56 volts be going thru the relay? I know the battery is good and can't find a wiring diagram online anywhere.

[@renewyourmind1815]

My mower wouldn't start. I took the bottom cover off like you showed. A mouse promptly ran out. Some wires are chewed. I am pissed. I bought this mower new, I'm a single mom, I have no idea how to fix this. Mice have chewed wires in my pickup and now the air doesnt work. Every year its a battle! I kicked the damn mouse & its dead, so at least there is that. Have to take the mower in now & I am BROKE already! I'm so frustrated!

[@trevorphillips2868]

5 years seems to be the sweet spot for this issue. Safety features are dumb. I used power grips to fix the dumb to by pass the kill switch. They should have just used a wire cable to pull a lever like gas mowers.

[@clintonwacker994]

My mower won't start. Just hear a "clicking" sound from the motor area. Hope it's not that relay. This looks like more trouble than it is worth. Only had this mower 1 year. I will try and check the circuitry and hope I can find what is wrong. Yesterday it worked fine!!! Today nada. I have folded this mower up at most 3 times. Can't believe that the wires are bad.

[@clintonwacker994]

Remember to save your receipts AND register your EGO products on line with model and serial numbers. It will save you so much time if you have problems. Thanks for your great video. 😀

[@mr.n.exclusive3606]

My lever is stuck and will not fold. How do you fix this

[@sh1529]

Does anyone have a link to a schematic showing the electrical wiring?

[@randyfleming3004]

Thank you ❤❤

[@TJ_775]

I have a flashing yellow light at the top of the handle. Motor seems to get a shot of power, blade moves just a a small Jerky movement. Battery works in the leaf blower. Any ideas

[@jamesf786]

Hi TJ. I wish that I had the answer for you, but our mower has the same problem as yours. Any chance that you have found the cause yet? I've been checking the wires and tried a jumper to skip some of the safety switches, to no avail.

[@h88sixtyone38]

This happen to me after first cut. Not acceptable for the price

[@kellytrower3602]

What toolz do you need?

[@kellytrower3602]

We can't remove the case to check the part relay you show. Deep screws.

[@sallyj632]

So basically, to lessen the risk of this happening, just don't fold it up it sounds? I keep mine extended when stored away because I have enough room in the shed to do so.

[@mohammedhashim2891]

Thank man it’s works

[@RickyDishon]

Thanks

[@jcbak]

After watching a number of videos similar to this one, I think I'll stick with my gas mower.

[@michaelvitale4029]

well, having my second problem. It went to Ace Hardware at the end of last season, and now, fully charged battery and it won't start AGAIN. Frustrated AF. When it was repaired, I was told it had something to do with folding the handle down over and over. Guess what, it's designed to do that for easy storage !!!!! Back to Ace Hardware. Hopefully the warranty covers it again. WTF

[@allyourtechai]

Hopefully it works out for you. I stopped folding mine unless I’m storing it for the winter. My new wires should hold up better, but it’s definitely a design flaw.

[@teressasutton8295]

The page where I may also be the problem but I have not been my handles up and down but a very few times

[@allyourtechai]

I hadn’t used my handles very much either, maybe a dozen times before it became an issue. Now I just fold it when I store the mower for the winter.

[@teressasutton8295]

@@allyourtechai well it is raining here and has been for a couple of days and supposed to rain until Monday I think I think I’m going to move it on the screen in porch in a little while and work on it I was so excited when I saw your video I just had to try once I had tried to get into where they relay was but I don’t remember now I don’t think I could get all the way to it or some thing but at least I’m going to give it a try because it’s no good the way it is I’ve been working on cutting up a tree that fell on my house and across the neighbors fence it broke they Roof and correctly wall All the way to the floor oh well at least it keeps me busy

[@RyanJohnsonHQ]

Got mine in January, 3 months ago... and I'm troubleshooting it.. pretty lame.

[@maryjanehutton4285]

My mower starts, the blade is loose enough but doesn't engage.