AlphaRex Step-by-step Installation Video for 2016-2021 Toyota Tacoma Projector Headlights

Here is the step-by-step tutorial about how to install our AlphaRex NOVA-Series projector headlights for 2016-2021 Toyota Tacoma

[@unavailableunavailable4763]

I just installed mine, took me 5 hours to do so, because this installation guide is very poorly done and not step-by-step at all. For example where to push or pull to remove certain parts like the grill or the fender flares, where to run the wire from the fuze to since the fuze box is sealed, what to turn to adjust the lights. None of that is explained. But now I got it done, just few things to improve, and the lights look great.

[@theNVMEproject]

Make a video on how to wire it for the light show

[@steveduranko4911]

You do not need to plug in the grey wire to the fuse. I just installed mine today on my 2023 Trail Edition and everything works perfectly as it should

[@LMarshall73]

Any guides planned for the 2012-15? All connections accounted for and both DRLs hyperflash at the same time for both turn signals. When I don't use the DRL harness only the hi/lo beams work. Edited to add the solution. The plugs on the headlights are wired incorrectly. I had to repin one of the connectors (3 pin with black and yellow wires) the black wire should be in the center where the OEM ground wire is. The yellow wire should be where the black wire was. Luckily nothing shorted out. The turn signals still hyper flash, so I’ll probably need to add load equalizers.

[@WinterWolf_92]

Can you do a vid for the 2nd gen tacoma's 2005-2011 models . I have extra plugs hanging out still and it does a hyper flash when I signal

[@monnddo]

I got a question it is normally when u lock the truck the drl light turn on then it turn off while u not using the truck I just notice it my truck?

[@yebron69]

Does this work for 2021 Toyota Tacoma TRD?

[@wackedout13]

I thought it was plug and play why do you need to plug in DRL to the battery if the factory lights don’t require it? I seen other install videos with plug and play like for like

[@felixalonzo8593]

Good question

[@threedaysg3479]

Just installed them, it’s only if you want the startup sequence.

[@mct8888]

@@threedaysg3479 so you can install without that box?

[@banksbvloggin1896]

Does this work for a 2022 tocoma?

[@JDoggoftheNetherlands17]

Damn that positive battery post had a lot of corrosion

[@davbruh3456]

Hello can you switch the DRL to amber color ??

[@martincasillas7348]

can you switch from clear to amber om your drl?

[@jasonchard8327]

How?

[@snipes6075]

My drl won't turn off. My truck has a mode for drl and it stays on

[@effinhaoli808]

No mention about trd wiring and the info about wiring you show is super vague...how is it that every other install video for your product ,is way more helpful than this 5 minute video 🤪

[@TravisNobles]

Turn WHAT clockwise or counterclockwise to move the headlight up and down?... You don't show it in the video, what are you actually rotating??

[@jonc7371]

theres a dial on these to adjust the height

[@isaacdiaz1358]

Hello I installed them and during the day the drls turn on by themselves.

[@ulyssesrodriguez8118]

Same

[@Michael-pp8lz]

Use the INJ fuse, not the EFI. The EFI will automatically turn the lights back on after about 4 hours due to an automatic emissions check

[@Kkaden]

Michael is correct for anyone who is wondering

[@Syq0tic]

@@Michael-pp8lz I used the inj fuse and the headlights led drls stay on all the time, used the efi one same thing