AMP Research POWERSTEP Unbox, Install, and Review

[@Area51Base]

I purchased a set from a local 4wheel shop with free installation few years ago. I love them.

[@GearsGadgets]

Yeah they are an awesome addition and a real nice feature.

[@sockmonkey22]

This is perfect for assisting a senior citizen getting too old to climb, or someone with bad knees if you buy anything beyond a sedan. I do senior caregiving and if I pull up with a Jeep or truck this extra step would be awesome.

[@GearsGadgets]

I agree. They have a lot of uses. My 3 year old LOVES them.

[@1sicsrt]

I have these on my truck! One of the best improvements I've made to date!! Amp Research didn't have any of them, but Amazon did!!! So it worked out well!

[@dwightraine9686]

I have a pair on my 2016 Ford F150 lariat model, i’ve had them on my truck for about two years now and a great and wonderful everybody loves them makes it easier for my wife to get in and out of the truck the great product. They’ve been flawless and the way they operate I’ve had no problems with them they’re out of the way when you don’t need them they quickly deploy when you do.One of my favorite purchases

[@GearsGadgets]

Totally agree, they get a lot of great comments and they work awesome.

[@BAGINAZARD]

06:58 Might want to get the AMP Research Override Switch because standing on that will cause heavy strain on the gears, and motors over time. That will lower the life expectancy of them in the long run. The switch is also real simple to install and they allow you to keep the steps up when you don't want them out, and down when you want to clean them.

[@GearsGadgets]

Thank you TRICKSTA. It is on my agenda.

[@ThenewguyYT]

I was always curious of how this worked till i was tasked with installing a set on a 18 Dodge ram at work the other day and it was the most fun ive had at work in a month!

[@GearsGadgets]

Sorry for the super late reply Thenewguy. I appreciate that you stopped by the channel and apologize for not responding WAY sooner.

[@drewjames8594]

I just installed these on my 19' 2500 and as soon as I stuck the fuse at the hot wire in the steps raised up and won't go down when I open the doors. I assume this is the same instal as the 18 you did so I was hoping maybe you could point me in the right direction. Did you ground to the frame and where did you tie in the hot wire to the battery. This battery has like 5 different locations and Im thinking this may be my problem. Thanks in advance!

[@Steve007362436]

My driver's side developed a clicking sound when they reach the fully retracted position and if deployed I can pull it up slightly and get the same click. Called customer support a couple times to help troubleshoot. Ultimately they recommended about $50 in replacement parts. Dealership installed when truck was new, that was three years ago and they haven't needed anything other than lubed until now.

[@GearsGadgets]

+Steve007362436 that’s pretty solid. I had no issues with durability but I have read other reviews that say they are holding up. I’ve seen some complaints of icing up, I didn’t have any problems in Buffalo, NY with them.

[@Steve007362436]

I replaced the main shaft and brass drive gear, also a wedge that locks the upper link into a flat on the main shaft, kinda hard to describe. Working perfect again. Really nice to have with a 6" lift and 325/60R20 tires and the truck looks better with them hidden away.

[@mikemestas8446]

I had the dealer install my AMP Boards and I loved them till they started to either not retract or deploy. I contacted AMP thru the warranty information provided with the paperwork. They gave me suggestions to fix them myself, I did everything they suggested and they still give me trouble. Wish they would provide me with some options to finally get these fixed. $1500 I should be provided with options to get these fixed……

[@GearsGadgets]

Man sorry to hear that. How long did you have them before they started acting up?

[@mikemestas8446]

About a year later after the installation. Nothing happened to the truck or the steps to cause them to act up. For whatever reason I have the most trouble in the summer months. There’s no rhyme or reason for them to act up. Sometimes they stay down and won’t come up and sometimes they won’t come down. Doesn’t happen all the time just randomly. @@GearsGadgets

[@rawirihemi27]

This is the one reservation I have with them, I feel like they are not going to work in a short amount of time.

[@MrHermangv]

That’s where am struggling to decide to buy them or not, I know that those type of mechanisms will eventually fail..

[@rockytopvfl8350]

Hold on, so I spend $1500 and the first thing I have to do is take a miter saw to them??????

[@clayrev]

yeah, I had hard time at the dealership when I bought my new truck explaining the difference between a double cab and crew cab to the sales man.

[@briant3403]

1200 per side i was told,

[@Livinoutdoors_]

Cutting only when you have a extend cab. Just buy a crew cab ;)

[@nathanplatt5517]

I have an extended cab truck too but I left my steps long so that way I have a little step to reach into the front of the bed of the pickup.

[@adambright2761]

@@nathanplatt5517 you just answered my question, thank you.

[@wrathcustoms9566]

These look so good and the way they drop down is awesome.... but $1500? Nah I'm good

[@GearsGadgets]

Fair enough

[@michealshelton2133]

$1,500!?!? Yeah. I'll just wait 10 years lol

[@rudy-vp2wg]

Right?.

[@izzo4160]

For real. Madness

[@philmcclenaghan7056]

You bought a $70,000 truck and complain about $1500....

[@angryfishing7958]

I installed a switch on my steps so when I go mudding I can turn them off. If you don't as soon as you open a door the weight of the mud will not let them come back up. If you continue to mud and hit a good rut....say Bye bye steps and warranty. Experience speaking.

[@GearsGadgets]

I am going to add that switch too.

[@angryfishing7958]

@@GearsGadgets Amp told me on the phone that is something they wanted to be part of the kit. After talking to lawyers they decided to much liability. Someone would forget and fall. I said I'd rather fall than dish out a 1000$. Anyway be safe.

[@nemesis851_]

I've talked with a good number of AMP Research step owners (IN-PERSON) at their vehicle here in Canadian Rockies. Very low satisfaction rate, with most all of the units FAILING in 2 years or less. Asked if they, a after market shop, or dealership installed prior to delivery (most pre-new delivery) Real world experiences, with actual owners, in front of my eyes (not online), right where I live. I would have bought these (or the HD edition) had the results (life expectancy) been better.

[@dmitryn.4403]

I know many guys that don’t have any issues with them I guess it’s a hit or miss

[@j.p.speers]

This is correct not only have mine failed within the 1st year, but AMP will not cover any parts without the installing company charging the customer way crazy money to prove the parts failed. This company is unethical and does not sell reliable and dependable systems.

[@bc_usa]

​@@j.p.speerszzzzzz 😢waaahhhh!!!! 😂😂😂😂

[@bc_usa]

AMP is an American made company. Maybe they just don't like them Canadians 😂😂😂😂😂😮

[@poke85]

i have them on my 17’ sierra, when i open my doors people look like it’s something from the future like they’ve never seen em before

[@GearsGadgets]

I totally understand. I get the same thing. It’s like you’ve just stepped out of a space ship.

[@jakei8310]

Just so everyone knows, you can convert inch lbs and ft lbs. it’s a multiplier of 12.

[@dhansel4835]

My experience today was a disaster. I have a 2016 RAM Laramie 1500 truck. I had the chrome steps but they were too close to truck to be any use. I went to the dealer and had the automatic step running boards installed today. They seemed to work OK. I drove down to Home Depot which was about 2 miles down the road. When I got in of the truck the running boards retracted then extended and retracted over and over. It was doing this on both sides. My wife was upset not knowing if they would just break and fall down. We were about 1 mile from the dealer so I headed down the feeder road all the time the running boards were banging up against the truck. The accessory lady came out and saw what was going on. I video recorded this while they were looking at this. She called the people that put them in and told her to leave the truck. I got a loaner truck from the dealer and went home. This was my experience with the electric running boards. I hope they can get this problem fixed as soon as possible.

[@GearsGadgets]

Good lord, sorry to hear that. Were they AMP boards?

[@dhansel4835]

@@GearsGadgets I saw initals on them but I didn't have them long enough to get a good luck at them. I never heard so much noise as these thing were slapping against the truck in my life. I hope it didn't break any gears on the motors. I guess I will pick it up after lunch today. I believe these dealers are having authorized 3rd party people that make their rounds installing things like electric running boards, bed liners and bed covers.

[@dhansel4835]

@@GearsGadgets Yes ! I got the truck back this afternoon and took a picture of the logo badge on the running board. It was the name AMP RESEARCH. They seem to be working now. Boy what a sound as they were opening/closing/opening and closing over and over. I thought they were going to tear themselves apart.

[@chrissalazar7146]

What type of paint did you use when you drilled through the frame when installing the step lights.

[@Jerry-Lerry12]

Would they sell one of these for a single cab ? I’ve been looking for one but can’t find any?

[@danlarson8154]

Hope you get a response! I’m wondering if there’s enough room for the rear hinge and motor assembly. Looks pretty tight under there. The rest looks fine.

[@joshnadamproduction]

Would suck when the battery goes weak or as a motor wears out years later but I do like the hide away looks sleek

[@GearsGadgets]

Motors on mine haven’t worn out but in all reality even with that consideration, most running boards I have seen end up pretty battered and weathered after several years with all the rocks that come up from the front tires, mud kicked off boots, and in the northern climates, snow that turns to ice chunks full of road salt that just eat them alive.

[@ronhobyak9902]

My wife is handicapped, We use a step on the ground for her to get into my 2012 Jeep Grand Cherokee. Is there there a product on the market for just the front passenger side? And can I get it installed with handicapped insurance funds for free? Any suggestions ? Not used as off road just used on city roads mostly. MI

[@HUMINT1]

thanks for the info. Im curiuos when showing the drain plug why you did not try and run the wires through the opening with the other wires vs drilling into the plug itself? I am in the market for these steps but have not yet purchased them.

[@wild1595]

Just bought a 2021 silverado z71 ltz with these on them! I knew nothing about them and was wondering how to keep them out to wash them lol Thanks for the video

[@bryce1916]

I have a lifted truck, and I am 60, so these make it a dream to get in and out otherwise I would not be able to .lol.

[@brendonjenson3156]

Hi of your still around to answer questions are they still working nice now or what? I really want these but I don't want to spend that money if they eventually break.

[@GearsGadgets]

Im still around. They work great and I had no problems with them. I don't really hear of anyone having any issues with them. I do recommend the extreme version which I upgrade to because I have a good relationship with AMP. The extreme has 2 motors on each side which is just a better setup, but I didn't have any issues on the standard ones either so its up to you.

[@hinglemccringleberry7786]

I'd worry about slush, snow, rocks. I guess if I lived where the weather is more temperate, they'd be fine. But as I drive across Idaho, MT, Wyo, ND and SD in the winter, don't think they'll last for me.

[@GearsGadgets]

I am from Buffalo, NY and it held up fine, im in Arizona now but never had any issues in the snow and lord knows there was plenty of it in Buffalo

[@dshudson]

Mine are so bad in the winter I just leave them out

[@terrygugel3803]

Wonder if you can get these for older vehicles ? Love to put a set on my 79 Bronco

[@SATOSANNN]

I’m sure if you got the mounting points they can be done

[@anan7s294]

Where do u put the jack after installing these? If someone accidentally places the lift under these steps, and lifts the vehicles up for service will it hold the body weight and still function normally?

[@therookie5263]

Would have been awesome if you showed where under the hood exactly, you hooked to.....

[@GearsGadgets]

Sorry.

[@liamwalker6024]

Hooks up to the battery, negative to negative and positive to positive

[@mickberry9991]

Ok, so what about when it is snowing? Do they still operate as easy as they do when it is warm weather? Will Snow and Ice hamper the rails from working correctly? Will they get frozen from water and Ice build up? Will they work on a Regular Cab Short Box? Do I cut them to size as well? I know that these are a lot of questions, but before I spend $1500.00 I would like the answered to these questions.

[@GearsGadgets]

No troubles in snow.

[@5thGenNativeTexan]

I put a set on my lifted F-150. I'm very happy with the steps themselves, but was very disappointed with the lights. You'd think that for $1,800 they could include some decent lights that are brighter than a $2 flashlight. Pulled them off and replaced them.

[@GearsGadgets]

Interesting. What did you replace them with? I personally thought the ones that came with it were fine but just my opinion.

[@5thGenNativeTexan]

@@GearsGadgets Way too dim for my liking, and apparently it's somewhat of a common complaint as I read the reviews. I just found some short, 6-8 LED waterproof "strip" lights on Amazon. Very flat, the "COB" or Chip on Board LED style. Was literally $10 for a set of 4. amazon.com/gp/product/B087Q4KG95/

[@doseofjj2189]

Sorry I don't know if I missed it on the video or not but did you install the the lights aswell when they unfold..?

[@GearsGadgets]

yeah I did, not sure if it was in the video or not but it’s literally just double stick tape and takes seconds to install.

[@koloasurf2012]

I wonder if this will work with the Rivian R1T? Love some feedback.

[@Doc1855]

I am saving up to buy this for my 23 Tacoma TRD Off Road double cab

[@ronmcmanus9]

Hey! I was checking out your video and wanted to know what is the title of music you're playing in the background when unboxing boards???

[@truck2930]

Do they open when the vehicle is running

[@cal2201]

Wish this could be a factory option for all major auto manufactures...

[@GearsGadgets]

Agree

[@guojiefan5380]

Will it be activated if I open the other 3 doors except driver’s door?

[@Losman666]

Do all amp steps require plugging into the obd2?

[@coreypatterson1386]

1 of my amp research boards will not fold up when I shut my door. The board is trying to fold up because I hear a clicking noise when I shut the door. I dont believe I need to replace the motor....any suggestions as to what I should try???

[@GearsGadgets]

Hmmm, unfortunately I dont know. Did you reach out to AMP?

[@luisg6887]

Are the best for my gmc Sierra

[@dmitryn.4403]

How are the steps holding up?

[@rickywright3894]

Question. I cant find this info anywhere. How far do they extend down? Like ,in inches from the cab? Installation looks pretty easy

[@DvauLt117]

Hi, is there any option for me to use it on my 2003 CRV and my 2000 chevy blazer?

[@rickygonzales5939]

Will both steps retract if both doors are open at the same time,or do both automatically retract if one door opens?

[@GearsGadgets]

They operate independently of each other. Each side only expands and retracts if that sides doors are open or closed.

[@B2M54s]

Do you think this will fit on my 2007 jeep grand cherokee?

[@vladimirmendez6445]

because I can't get more electric running boards for pickup trucks with regular cab on the amazon pages and other sellers ... could you tell me a page or catalog that distributes them

[@GearsGadgets]

I am not sure because I am not sure how the mounts would work on that cab. Not sure if it would work

[@vladimirmendez6445]

@@GearsGadgets thanks

[@Hxsanchez1]

Is there any maintenance involved such as lubing gears or anything else?

[@GearsGadgets]

No

[@richardguajardo2393]

Is there a way to set the delay on when the running boards retract? I notice in most vids I've seen they have a couple of second of delay before retracting, mine retract almost right away when the door is closed.

[@GearsGadgets]

Really??! Mine wait a second or two. I do not know how to change it.

[@AK-dl4ng]

I want it how to order it

[@GearsGadgets]

Link in vid description

[@jsclaveria4518]

Do you have this for Jeep Gladiator 2022 model? Hm?

[@danlarson8154]

Does anyone know if these can be modified to fit a 2018 Chevrolet Silverado 2 door Reg Cab? Not really sure if there’s enough room for the rear motor and hinge assembly. Would really appreciate any help, answer or video. Thank you.

[@danielphillips9977]

Are the lights sold separably?

[@GearsGadgets]

Nope, comes with it.

[@griff3n69]

How hard is it to get into a truck lifted say 6" with PowerShell? Trying see what will make it easier to get into a lifted for someone unable to jump daily

[@Sig721Tau]

Then, maybe you shouldn't be driving a truck with a 6" lift. 🤷🏽‍♂️

[@GearsGadgets]

These would be perfect for that.

[@TypeUsername34]

Do they have a pinch protection?

[@GearsGadgets]

Yes they do. They will stop if anything gets in their way. That’s actually how I lock them down to wash them is just put my foot on them and close the door which then locks them down when it senses pressure it just stops.

[@TypeUsername34]

@@GearsGadgets so if you were to buy your hand or fingers there it'll stop itself? I've had my gf close the door on me when we were washing my truck and yea, wasn't pretty. So just trying to see if won't smash my hand if I were to have it there

[@Doc1855]

The new ones have dual motors on both sides

[@WH6FQE]

ahhh shoot. I was realling liking these, but I do not have OBD2 on my Chevy dually, just OBD

[@GearsGadgets]

How old is that dually

[@WH6FQE]

@@GearsGadgets 1990. It has the older original OBD port under the dash that I jump with a paperclip to read the codes. I bought it because it is the only 1-Ton 4x4 Chevy Dually in Hawaii, and it only has 38K actual miles on it.

[@Blood1Zero]

They sell a hard wire kit too.

[@jafferhabeeb]

Would this fit on the 2021 Jeep grand Cherokee Trailhawk ?

[@robertmoore5196]

So most of the mounting is done to the lower rocker? Bummer, in northern states we don't have rockers very long.

[@billyjones9045]

I need a driver side one I have all the hardware but the guy I bought the truck from busted it off somehow .

[@1g4u]

Do they hold up in snow mud and or under water?

[@GearsGadgets]

I haven't had any issues in any of those scenarios. Under water seems a bit extreme though.

[@ChannelOne-1]

Seriously! They don’t make a step that will fit without chop sawing it???

[@GearsGadgets]

You could just leave it long

[@DK-hy2fs]

Essential for off-roading

[@GearsGadgets]

+Aus 4040 I agree. Keeps ground clearance up. I’ve had other running boards get pretty beat up off road from high centering.

[@cesarvillanueva7285]

Aus 4040 y

[@GREED_GMN]

Can these go on a 2024 Nissan Pathfinder SL?

[@GearsGadgets]

No

[@ozzythegod55]

Wondering if this will fit my 2004 Chevy avalanche?

[@GearsGadgets]

I am not sure, you would have to check their fitment website.

[@Varedz]

Im getting these i have a 14 inch lift on 2013 powerstroke and i cant get in i have to cilmb threw my rear window from the bed and thats a hassle.

[@GearsGadgets]

Thank you Varedz

[@dhansel4835]

My followup. I got a call from the dealer and said my truck was ready. When I opened the door I saw the name on them was AMP: I sure hope they don't go out of control again! That would tear up the gears in the motor unit. Another thing when they hooked the wires to the battery the positive battery protector cab won't fit. When I close the hook the naked 12volt terminal is close to the hood.

[@GearsGadgets]

Hmmm Thanks for updating. I appreciate it. Happy they got it fixed.

[@chrisratliff5273]

They stopped working on my 2018 GMC Denali. Is it a fuse problem

[@GearsGadgets]

Hmm interesting. I’m not sure

[@calebsutton4723]

So what if something is already plugged into the ODB

[@GearsGadgets]

You can get a splitter off amazon for a few bucks.

[@408Berto]

I have a question I’ve had mine for quite sometime know since 2012 but the drive side doesn’t go up how would you recommend I fix that check the the motor ?

[@GearsGadgets]

I dont really know, I would contact the manufacturer. I would say the motor might be shot.

[@11211lcb]

Contact the manufacturer.

[@richardburlingame7860]

Leon Bridges pull the fuse out of the module. It should reset. I have been through two modules on my 2018 already. The modules get too hot under the hood and melt on the inside. I am going to reroute mine to the inside of cab.

[@YOUNGGRADER509]

@@richardburlingame7860 where is the fuse

[@richardburlingame7860]

JOHN C my fuse was located right next to the battery in a holder. It’s a 20amp spade type fuse.

[@theoutdoorsman7408]

Does anyone use these in the cold like if I wanted to put these on my truck in Minnesota where it’s gotten up to like -6 for the high all last week I guess the worst thing that could happen would be them freezing up.

[@GearsGadgets]

I used mine in Buffalo NY for a while and they were fine.

[@cubanosunidos5]

Hi, how much would this installation cost?

[@GearsGadgets]

I couldn't tell you, depends on the shop and I have never priced it because I DIY everything.

[@thecommoncarpenter6544]

I put a set of the original "Bestop" brand on my 2010 ram when I bought it new. The first winter they started having so many problems, went through 3 motors, steps would hang and not go back up. Finally ripped them of after 2 yesrs and threw them out. Someone mentioned to me recently you disconnect them on the winter. Anyone else have these problems?

[@GearsGadgets]

Thank you Matt Fischer. I have not heard of that.

[@samatdj]

Impossible for installation for toyota highlander ?

[@GearsGadgets]

I wouldnt put them on a highlander

[@ZEDNANREHIGH]

I'm trying to find these retractable running boards for a 2011 Jeep Grand Cherokee. Anyone that might know please let me know.

[@GearsGadgets]

Im not sure if they make them for a grand Cherokee.

[@dannygonzales2528]

Do they come with exterior lighting

[@GearsGadgets]

Yes. LED lightning is included. You can check out the link in the description for more information on what is included with them. Appreciate you watching!!

[@ricardohidalgo608]

must they be permanently connected? on OBD2 ?

[@GearsGadgets]

Ricardo Hidalgo you can disconnect them but they won’t work disconnected. It’s really easy to unplug it if you need to access the OBD2 but for the most part you just leave them plugged in and forget about it.

[@holdingnutria5622]

@@GearsGadgets some people use the port for other stuff. I have a cts monitor that uses the port. Any other way around that?

[@apr9286]

Great question so is there a way around it. I need to plug my BANKS idash into this too. But my Amp is plug into this. Pls. Help???

[@ClearLandSolutions]

@@apr9286 they make OBD2 splitters so you can connect 2 things at once

[@mattlaskey782]

One torque wrench in inch lbs, and one in foot lbs?? Was it the range that necessitated 2 torque wrenches? (That’s my guess) If not the range, then just do the conversion and save a few bucks.

[@GearsGadgets]

2 wrenches with different ranges.

[@mattlaskey782]

Gears & Gadgets .....good to know. Thank you

[@CartwrightFour]

So if you need to plug something else into OBD II you have to unplug your steps?

[@GearsGadgets]

Yes temporarily. Or you can get an OBD II splitter if you want to have multiple things plugged in all the time.

[@badimpulses17]

I'll save my money and just use a stool.. lol

[@GearsGadgets]

manifest 73 lol. That works too.

[@Sig721Tau]

manifest 73 Then, why are you on here? Manifest yourself out here. Lol

[@1231234abcab]

.... you just told him to appear out here... meaning staying in the comment section 🤣 Think you meant 'out of'

[@abelmonreal2787]

I have a programmer connected to my obdII. How can i make these steps work with out removing the programmer?

[@GearsGadgets]

I would probably try a splitter like this: amzn.to/2VymtFs I haven't had to try it so let me know if it works.

[@johnvisser946]

Gears & Gadgets motor

[@Kookaburra4509]

Is there a reason why AMP doesn’t make this product for the Honda Ridgeline??

[@diegoenamorado]

Because hondas are for pussies maybe??

[@JuanAlvarado-fv6xn]

Eewww I wouldn’t even make parts for those if I owned a company lol

[@wblynch]

They only make them for TRUCKS

[@williamcoons5756]

These are for TRUCKS.

[@GearsGadgets]

I just dont think it would sell well for a ridgeline.

[@h2oskiaddict]

Kind of sucks if you have other ODB2 devices you need to plug in. IE a Bluetooth scanner that you use to real time monitor engine data.

[@GearsGadgets]

You can get a splitter and have 2 ports. Pretty cheap.

[@rachaelhanna3256]

Do they work on vans ??????

[@GearsGadgets]

You would have to check here: m-amp-research.biz/Mobile/Portal/Default.aspx I am not 100% sure. You may need to look more toward a handicap van outfitter for something like that if AMP doesn’t have them for your van.

[@bigmenswagger]

How long it takes you to install them?

[@GearsGadgets]

Only a few hours. It's pretty straight forward.

[@shanetseng6040]

Hey, how are they holding up now? They look pretty solid though By the way, is yours with "2 in" extension or just regular?

[@GearsGadgets]

Mine are just the regular. No 2” extension, they would be way too low with the extension unless you had a lift. They are holding up awesome. Wife and kids love them and I love that I don’t lose any ground clearance with them. I recommend if you can afford it.

[@shanetseng6040]

Awesome! So if I plan to do a 3 in lift, do u think the 2 in extension kit would be good?

[@GearsGadgets]

100%

[@p0go598]

Anyone have issue with these not closing properly or jammed

[@davidkay92]

whats the weight capacity of these steps

[@GearsGadgets]

600 lbs per board.

[@davidkay92]

@@GearsGadgets is that on the regular steps or the xL models

[@pucky765]

How are they holding up

[@GearsGadgets]

Great.

[@JustCallMeTango]

How about now?

[@universalexports6119]

I have these on my '18 ram mega cab. Had them on since new, definitely like them...BUT anytime I have the tow/ haul button on for more than 5 minutes, they don't work.

[@GearsGadgets]

Really!?!?! That is bizarre. Must be an OBDII thing.

[@brewcrewfishing]

Just ordered a set yesterday for my F250. Can't wait! Go BILLS!!!

[@mrbig921]

I came to these comments just to say that I noticed that rather nice looking headgear he was sporting...lol

[@GearsGadgets]

Sorry for the super late reply Chris Brewton. I appreciate that you stopped by the channel and apologize for not responding WAY sooner. Go Bills!!

[@todd8781]

Constantly plugged in to the ODB II port?? Hard pass.

[@GearsGadgets]

What else are you doing with the OBDIi port when you aren’t running diagnostic the .0000001% of the time you plug in a scan tool.

[@todd8781]

Gears & Gadgets wireless OBD II transmitter for real time gauges, stats, diagnostics. Much better use than motorized steps

[@GearsGadgets]

Oh fair enough. You can just get a splitter and run both.

[@Shellieru]

I have been waiting for 4 months for my steps. No communication from them and I'm so incredibly disappointed in this whole experience.

[@mohdnazmighazali6210]

Where i can buy it?

[@GearsGadgets]

The internet.

[@UzumakiNaruto010]

Amazing mod 🥰

[@chris18228]

Should have use thread locker and should’ve said the max weight

[@GearsGadgets]

I agree chris18228. Thanks for the comment.

[@FROGMAN524]

Nice install.

[@GearsGadgets]

Thanks FROGMAN524, I appreciate it!!!

[@sangpi9322]

what about for toyota highlander

[@GearsGadgets]

Unsure. Check their website they have all vehicles listed.

[@Padoinky]

My 2016 Escalade ESV has factory installed hide-away running boards that my SO and little ones use

[@GearsGadgets]

Yeah the little ones love the steps. Makes them able to get in and out with ease and safely.

[@crashweaverda]

Won't work on my truck obd2 plug all ready occupied with my livewire tuner.

[@GearsGadgets]

I have seen some ODBII splitters. Maybe look into that?

[@alexgrech4420]

A little over a year the paint or antie slip is wearing off where I put my running shoe step not impressed

[@andrewf.909]

but would it withstand a Bills Mafia body slam from the top of another truck? My guess is no.

[@GearsGadgets]

HAHA I doubt it. Also, I am more ashamed of the body slam association with the Bills than I am loosing 4 super bowls in a row. I love the drunken tailgate parties but the table slams are just dumb.