AMX4: X-Ray Generator Calibration with Raysafe2 - Advanced BMET

[@mosesanjugu8697]

thank you so much, this is very helpful.

[@HTMWorkshop]

Glad it helped!

[@samherzog-yv6mt]

Great video 👍

[@HTMWorkshop]

Thanks!

[@arod8664]

Are these procedures the same for AMX 4 plus?

[@HTMWorkshop]

Yeah they should be nearly the same - some of the boards are a bit different looking - depending on when the amx4+ was built but overall pretty much the same. Of course it’s always good to check the documentation for the model your using

[@engr.israrahmad3194]

Thanks so much How to calibrate drive handle

[@HTMWorkshop]

GE has a documentation portal - you'll need to get the service manual for the AM4+ and use that to calibrate the drive handle - its not to hard, its a pretty quick calibration. If you know how to get to the service mode of the machine it will sort of walk you through it on the prompts.

[@muhammadsajjadaslam6464]

When i power up machine i get error XRAY DISABLED I JUST REPLACE NEW BATTERY

[@muhammadsajjadaslam6464]

@if possible may i have your contact??

[@Realgrowinstant]

My Amx-4 shows (disabled xray) & ( dives only) please help me

[@HTMWorkshop]

You have to do all the calibrations to restore functionality - including taps. Once you start the generator calibration you have to do all the others. Each calibration builds off the previous one so make sure you do them in the correct order

[@rolandocanizavillanueva1110]

when I try to do the calibration mAs I get Xrax Word limit. And it does not allow me to continue with the calibration kvp

[@HTMWorkshop]

I have not had to deal with that one - I know there are some ideas on Medwrench for troubleshooting that issue but not sure its the same. Sounds like an odd one.

[@HTMWorkshop]

If you figure it out please let me know

[@samherzog-yv6mt]

I had this same problem and found out if you adjust the kvp values by more than three each time the old memory chips hit a limit and kick you out of calibration. So only adjust by three (full numbers) max and it will take more X-rays but will complete the KVP cal in the end!

[@reubenmurey8876]

How can I solve the problem of blunt image on my Ge Amx4. The image is bad

[@HTMWorkshop]

Not sure on that one - have you checked any of the forums such as medwrench. You could also try asking r/BMET to see if they have any suggestions on reddit.

[@equaye6982]

can i calibrate without the raysafe? I dont have one.

[@HTMWorkshop]

I could be wrong but I believe there is a way to do it with an oscope and a voltage divider but it’s been a while - I think it’s in the manual if my memory serves

[@equaye6982]

@@HTMWorkshop Thanks so much for your prompt reply. I have got the calibration manual, i will check.

[@muhammadsajjadaslam6464]

@ 8:32 HTM WORKSHOP WHEN WE ON THE MACHIEN TEST 1 OK TEST 2 ON TEST 3 OK AFTER THAT XRAY DISABLED APPEARS

[@Andres-eb9gn]

When I try to calibrate Kvp, I reach 120 kvp but the machine turn off and restart the system for the begining

[@HTMWorkshop]

Interesting - I have not dealt with that issue before. Is the battery fully charged?

[@HTMWorkshop]

Also looks like someone else has had the same issue here but no clear resolutions - www.medwrench.com/thread/149877/amx-4-issue

[@qandeelnisar5638]

Aoa Sir From Askari Diagnostic lab Narowal Sir yesterday machine was charged on 1/4 charging.when charging was completed breakers was tripped and Now machine is giving the option (Test: 3 Failed)

[@HTMWorkshop]

Not sure - but the service manual does have troubleshooting guide in the back that you could try based off the thrown error code. Wish I could help you - let me know if you find a solution!

[@joelohamagor9462]

PLEASE HOW CAN I SOLVE ERROR 45B ON AMX4 ..PLEASE

[@HTMWorkshop]

Have your tried any of these fixes yet? www.medwrench.com/thread/120576/amx-4-intermittant-45b-error www.dotmed.com/virtual-trade-show/category/Service-Technicians/Discussions/Forums/Amx-4-Plus-Error-Code-45/8286

[@luisrosalesnft]

If you have the error on the calibration of the generator revise the condition of your fil/kvp board first

[@qandeelnisar5638]

How can we solve out (test failed 2....then test failed 3] error