An Easy Fix When Your Loader Has Quit Working

Usually about three times a year I get a panic e-mail or message from one of my viewers, because their loader has quit working. I like these messages because the fix is easy and takes about five minutes and doesn't cost anything.
You can tell you have this problem is you've been brush hogging in the woods, or, if you've recently taken your loader off and put it back on. What has happened is, a hydraulic hose has come loose from a coupler and all you need to do is plug it back in and you're fixed.
In the video I show a hose that's not attached. It will almost never be this obvious. Usually, all the hoses LOOK like they're plugged in, but one has popped out just enough to prevent the flow of hydraulic oil. The symptom will be that either the bucket won't tilt or curl, or the main frame of the loader won't go up or down...everything else will work, including the three point.
To fix the problem, turn off the tractor. If it's been running for an extended time, I'd let that hydraulic oil cool so you don't burn yourself. Then let the loader arms all the way down to the ground to take all the pressure off the lines, and then wiggle the joystick in all directions, just to make absolute sure the pressure is out of the system. Get your gloves and a shop rag and it's time to find the problem.
It may take a little work to find the hose that's unplugged. Like I said, most of the time it'll look like it's plugged in, but it's just loose enough that there's no hydraulic oil going through it. Plug it back in and test it, you should be good to go.
If you're around tractors long enough, this will eventually happen to you. The good news is, this is one of those easy fixes that'll allow you to get back to work quickly.
SUPPORT THE TRACTOR MIKE CHANNEL: / tractormike
Visit the Tractor Mike website: asktractormike.com/
Subscribe to KZbin Channel: kzbin.info...
Visit Facebook Page: / ask-tractor-mike-31211...
Buy Stuff I Use: www.amazon.com/shop/tractormike
Copyright 2017 Tractor Mike, LLC

[@DFWsportsguru]

Hey Mike, you literally just saved me a bunch of time and money. Mine would lift about 2 inches and stop. I came in and found your video on youtube and it was EXACTLY what you said. Re-seated the coupler and all is well. Thank you so much for taking the time to do this video.

[@airplanegeorge]

God bless you tractor Mike, you just fixed my backhoe. thank you thank you.

[@bryanmackey1788]

Thanks Mike, I did this to my tractor last weekend. One caution note, make sure the coupler is not damaged. My case when the hose pulled free from the quick connect I damaged the 'O' rings and couldn't get a good seal. Thankfully I have great support from my service department.

[@tools4meuc]

Thanks for the great tip! Just had this happen to me. First I checked the cylinoids at the bottom of the valve bank since previously I had to drain a little fluid out of them because the bucket was moving so slow going down. I did get a little more fluid out of them and thought when I put it back together it would work just like the last time I did it. Well, it did not. Messed around a little longer trying to figure it out, before I came in and found this tip by Tractor Mike. Went back outside and found one of the quick disconnect coupler was not in all the way. Thanks Mike!

[@nickcollins9237]

You fixed my problem!! Thanks a whole lot. My loader buck wouldn't til up. I did exactly what you said and every thing is working fine! Like your Video!!!!

[@dalerowe1614]

Thanks Mike, just experienced this symptom a few days ago. I'll check it out as soon as the rain stops.

[@dukeman7595]

You really helped me I tried bleeding lines and still the loader would not come down. I had been bush hogging when the loader stopped working, just as you said, and sure enough a hose came uncoupled. I want to thank you so much and the only way I can is by subscribing, and that's what I done. P.S. I called a local tractor mechanic who installed this loader and he didn't know, "maybe could be a a blown cylinder" was his reply.

[@bobpearce3665]

Hi Mike. Cheers from Maroochy River in Australia. Had this exact problem and your video saved the day. Thank you for your informative information.

[@1toolaholic]

thanks Mike, you described my problem exactly., even after bush hogging in brush. weird thing is, i usually have to watch a bunch of videos, but this time yours was the first one i watched. you are my now my number 1 youtube college professor.

[@TractorMike]

Glad I could help! Thanks for the support!

[@dukeman7595]

@@TractorMike Thanks again Mike.

[@BeardedRV-Tech]

Holy smokes, it was exactly the problem I had. One minute to fix. 😅

[@ignaciochavez7772]

Same thing happened to me first time using one of these things I was getting frustrated

[@tmac3515]

I was bush hogging today and my bucket stopped working. Thanks to your video I got it fixed.

[@TKeller115]

Thank you. I've been cutting up downed trees fron Hurricane Idalia when all of a sudden the loader would only go part way up and had limited power. The dealer is an hour and a half away and I don't have a choice I need the tractor functioning. It dawned on me to check KZbin and low and behold was your video. I must have bumped the quick connection as you predicted. Thank you very much.

[@donaldpoarch1651]

Tractor Mike you saved my bacon yesterday. A certain dealer with green and yellow equipment wanted to charge me $200 to come get my tractor and repair a bucket valve. I watched your KZbin and sure enough the hose had come unattached 30 seconds later I was back in business. Thanks for all your help we will keep watching.

[@dukeman7595]

They are proud with their prices on those green and yellow tractors, mine is the same color.

[@hearstdaman2269]

I just stumbled upon your channel while troubleshooting a loader issue. Thanks to you I was able to identify a coupling issue. In just a few seconds I was back in business! Thank you!

[@Kinja98]

Hi Mike. Thank you, Thank you Thank you...... I have a JD5075E with a Tenías T10 fel. Few days ago suddenly bucket wouldn’t curl. It did seem to have hydraulic pressure input, but would hang limp and not curl in or out. No leaks, no breaks, no bent pistons etc. Checked connectors, and all seemed well. Thoughts of major repairs by unexperienced techs ( not many tractors here in Curacao....). Bsed on your advice, decided to pressure clean the toy, and do complete check of all connetcors. Lo and behold in the rear, indeed, the hydraulic is tapped off from a rear aux output and relayed to fel.... one connector was slightly ajar....... fixed in 10 minutes. Ready to work again. Thanks Mike.

[@stevevaughan8155]

THIS just saved my life! I'm a new owner of a used Kubota BX25. Had just parked it, lowered the front bucket to the floor, removed the 3 pt hitch to prep it for hanging the backhoe on it...started it up and the frontend loader wouldn't budge. Moved forward/backward, rear PTO worked fine but the bucket nor the 3 pt hitch arms would move. Followed these directions and BAM! I'm up and running in less time than it takes to watch this whole video! Thank you!

[@TractorMike]

You're welcome! That happens once to every tractor owner so it's good you got it out of the way at the beginning :)!

[@HardwickOutdoors]

I was freaking out. Watched your bud and I had a hose loose like you stated! Thank you sir!

[@davehedblom5941]

Thanks much. Was in the process of loading it up for the dealership.

[@dustinbrearton4744]

First time watching a video of yours but if this is the fix you are the man. Either way I am subbed now. Thanks for the quick concise video.

[@davidschroeder4985]

You just saved me a lot of money, thank you for this video! John Deere dealer was telling me I had a bent cylinder that would cost over $1,000 to replace not to mention the hours of time lost. Paused this video at 1:09, went outside and reconnected the quick coupler, works great again!

[@TractorMike]

I hope I didn't cause the local Deere dealer to have to miss a boat payment :)!

[@EnoreeAD]

You're the best tractor Mike! I have a 2019 yanmar 424 and yes it was the bottom 2 lines that were disconnected. I was worried that I blew the hydraulic pump but like you said it was an easy fix. Thanks again!

[@TractorMike]

You are welcome!

[@belrix21]

Mike, thank you for the great tip, it was a great Christmas present!

[@dennisweaver8752]

Thanks for the video, I would like to know if you have a video on adjusting the joystick

[@jtoli100]

Thanks Tractor Mike. That was EXACTLY the issue and fix.

[@miriamtudman8994]

Thank you Mike. Quick fix.

[@brenthskll]

Thank you!!! I was frigging around and almost said screw it found your video and found the unhooked hydraulic line

[@gvrussell9230]

Thank you Mike!! Just fixed my problem!!

[@TractorMike]

Glad to help!

[@phillipking6153]

I’ve been bush hogging saplings. Went to tilt my bucket down to rest the tractor for the day. Wouldn’t work. Went straight to google. Found your video immediately. It’s exactly what you said. Thanks for the video. Two thumbs up!

[@TractorMike]

Glad you got it going! That's why I do this. Thanks for watching...

[@dukeman7595]

@@TractorMike I'm now one of your top viewers.

[@robertfennelly7442]

I just watched this and thought boy what a stupid issue to have. Well, I went out and checked and it was my Stupid issue as well. I guess when I was doing the oil filter change I must of bumped the hose connector. Problem solved, Thanks a Million.

[@peewee.3138]

When in doubt, read the owner's manual! Nice videos, Mike!

[@skotis_aboutit]

So true my friend!

[@frankdougherty3233]

Great point because - when it happens ... you just saved somebody!

[@bretsandefur3944]

Thanks I was worried.... got off everything looked right but was disconnected.... saved the day thanks

[@TractorGuru]

I love the sound of those spring peepers in the background!

[@hatterasfreediver]

U are the man!! Thank you sir!

[@Grottosays]

Thanks Tractor Mike!

[@byronbrackett6579]

Thanks Mike!

[@benjaminjensen4414]

Hey Mike, I have a 685 red tractor that would back up or maybe go forward sometimes, dad and I dont know how to fix it. Thanks

[@kfrey0501]

On this exact new holland tractor, i had to remove a cylinder for the bucket curl and have it sent off to be rebuilt, i also removed the 2 hoses that go to the cylinder so that those could be taken to the same shop to get a replacement since they were worn. When i get everything back and get it sll hooked up, do i have to bleed air out of the system before the bucket will work properly by leaving 1 of the new hoses a little lose until i get fluid out of it with no air? or does this system have some kind of autonatic bleeder?

[@terryconner6982]

Mike. My loader goes up when I try to put it down if my 3 point is raised completely. If I lower the 3 point just slightly down works. It started after I rebuilt the 2 cylinders for the bucket curl. Before that up and down were working fine. Even had good power down. I never disconnected any lines at any time. Fluid is fine.

[@saids7659]

Thank you, you are a life saver

[@lizkokolakis2402]

Wow we just watched this video and it worked u r a legend

[@doug7560]

hello, have a jcb217 older loader, after changing the hydraulic fluid the haudraulics will not work. Loader runs. Checked all lines for tightness and air. Any ideas?

[@ColsenKalista]

You are the man!

[@ronloranty4431]

Thank you mike that’s what my problem was

[@jamesgrows4591]

Thank you!!!!!!!!!!!

[@anthonygordon3513]

Thanks Mike

[@justatool]

Mike, is it possible to raise the arms on a disabled bobcat 873, I need to load it and don't want the arms dragging on the ground. TIA..

[@TMac0925]

My loader was working fine until few days ago. Works fine up and down and bucket curls down fine still but it is now REALLY slow to roll up. Checked all hydraulic hoses. All good. Fluid level good too. Any suggestions? Thank you

[@peterriccardi5933]

hi mike i own a massey ferguson i bent my loader bucket hit a stump while brush hoging the bucket is 3inches lowerr on one side of the bucket when its leveled i think my loader support between my loader arms is bent i tryied to jack up the lower side of the bucket and it dident work any suggestion thanks for all the info on tractors

[@yurizaichenko2783]

Thank you so much like you really help me

[@jeremymiller4908]

Thanks!

[@godisallaroundus]

Just put my box blade down and added on my brush hog. PTO lever seems locked. Over winter had a small leak. Any chance they might be hydraulic fluid?

[@jmay1342]

So I've been trying to figure out what's wrong with the loader on my Kubota. Low on hydraulic fluid but that didn't fix it. Came inside and watched this video (thanks for being short and to the point) Frustrated I say "this is BS" since my tractor is old anyway. Figure ok, I'll go check. Sure enough it was the upper fitting, not sure how this happened. Maybe when I was moving snow around. Thank you much....still learning

[@jimbuford4147]

I have a new holland with FEL and the loader will lift but it will not lift a round bale of high as it was doing. It will take the empty loader as high as before but not with a heavy weight on the loader. It looks like it if full of fluid. Any suggestions? Thanks

[@garlanwilkins2261]

Hey Mike I have a older model m4900 kubota and I blew a hose of my joy stick area so I replaced it think that was the fix .the loader will go up but it's hard to go down and will not curl .have I damaged A my pump or B my joy stick value. 😕

[@chips4289]

I have a different problem? if I set my bucket and left arms down to the ground, I can lift the front end off the ground by curling the bucket forward. now if I lift the arms up and tip the bucket so the cutting edge is facing straight down and then push the loader arms down it will not lift the front wheels off the ground.... also the lift arms just don't seem to have much lifting power at all while the bucket curl seems normal. could this be an issue in the valve body or the lift arm hydraulic cylinder?

[@ashleestockton9892]

I'm having the same issue with my 1533 hst mihandria but it's not a house with a connector like this one is a metal sorry if cap with a spring inside that let's the fluid run pump in and out. The metal call busted off and the hydraulics quit working by any chance would you know what that part is called?

[@timcunningham576]

Hey Mike, Yes very great video and easy to understand, however this tip failed to be the solution in my case. Working on the next step to fix my bucket. Everything works with exception to the bucket dumping Nothing wrong with the back hoe either. What is a good direction troubleshooting from here.

[@timb9257]

Thanks, I just blazed a trail through the woods, and my loader would only go 1/2 up. I though for sure mechanical obstruction. I googled, and sure enough, it was fitting popped just far enough to work, and when pulled ona little, came out far enough to stop flow. Thanks, I was by myself, and my tractor wont stay running when I get off the seat, so I can like work the lever from the side and see what is happening

[@markguarino1282]

Thank you Mike. I have a TN 70 A tractor. On the quick Disconnect the Pins don't come down even when using my full weight and a cheater bar?

[@TractorMike]

Mark, hate to tell you, something in the faceplate is probably tweaked. If it's a New Holland brand loader, those quick attach faceplates weren't the best in the world. E-mail me at [e-mail] with your loader model number and I can direct you to a replacement that won't have that happen.

[@mattywho8485]

If the quick coupler is not loose and your FEL will not function as it should, check the check ball in the end of the coupler itself, mine was broken and cocked sideways in the hole, not letting fluid pass.

[@dukeman7595]

Thanks for the tip.

[@CapeFrank57]

Hi mike, I have a problem with my loader, about half way down the front bucket slowly drops down.do you what the problem is Thanks

[@RyanFTW]

I've had a nut on the bottom of the loader joystick work loose and there was eventually enough play in the connection with the cable that it stopped actuating the hydraulic valve. It wasn't a sudden thing though, the loader moved slower and slower as the nut backed off over a week or so.

[@peterkesling1412]

Thank you for the explanation. I have this issue. Just was brush-hogging a woody area. The difference is that I lost all hydraulics. Gone through the couplers and all seated, except I cannot locate the coupler for the PTO. Still looking. Fluids look okay. What am I doing wrong here?

[@TractorMike]

A sudden failure when brush hogging a woody area almost always is a hose or a wire pulled loose underneath. I'd get the tractor to a clean area, put a big piece of cardboard on the ground and get a flashlight and search until you find the culprit. I'd bet you'll find it.

[@rigorousone1324]

when my loader is fully raised and bucket tilted all the way back, the bucket will not dump forward without help. otherwise works great... any idea?

[@dougcogswell6104]

Hi this is doug I have no hydraulics to the loader at all or the back attach ment will not work up or down .its hydrosta6drive that works good does the bucket have it's own pump

[@bradfordstewart5409]

Thanks Tractor Mike! I was just about to call the dealership and embarrass myself.

[@liztoth9490]

Ive got a JD 855 have lost control to tip my bucket; it still goes up and down. There is alot of play in the controller and looks like there are 2 flanges that used to be connected to something that aren't any longer .... Can you do a video on how to 1) get at them and 2) repair Thanks!

[@thomasdailey4566]

Liz toth, how did u fix it? My 755 joystick is very loose so I assume broken linkage.

[@richardmalvasio1270]

I'm trying to lift my fork and keep it up with out the use of engine. Is that possible? I have a Kubota mx5100 2009

[@jamiejackson9941]

Hey mr mike i have a tn 70a new holland with a brush hog loader the loader will only go up half way any thought

[@dukeman7595]

Find out where the adjustment is for the hydraulic pump pressure and try it.

[@shonsamples]

Mike, I have a front end loader on my tractor that seems to work fine with the exception that if I put the bucket on the ground it will not lift up the front end of the tractor. I ran across this when I was working on a tire. Any suggestions?

[@bigfoot3270]

There is a function in the joystick that causes this on purpose. You gave to push your joystick further in the position you was pushing it to lower bucket. There's a video on KZbin that will help you out. It's in under hidden loader tip are something like that.

[@corystevenson2041]

I have a similar problem but on an old john deere 510b backhoe. Loader will not lift. Back shovel works great. No lines disconnected. No air in lines.

[@deweybusby3686]

My new holland tc33da loader bucket won't stay up slowly leaks down I took apart the valve body and nothing seemed bad what could it be

[@flarenut1]

Mike I have a Kubota L2500 and the bucket tilt function will tilt back slow at times or be tilting back and stop. When this happens the bucket don’t have hydraulic pressure because it is easy to move with hand at that point. I then move loader lever back and forth and it works again. Do you have an idea on what is causing this.

[@TractorMike]

I don't but maybe someone will see this who has had the same problem and comment. You might also type your issue in your browser and I'd bet it'll take you to a tractor forum where someone has had the same issue and knows an answer. It's odd that it's not happening all the time.

[@ronaldcounts4119]

I have a international 260 backhoe. It runs and works fine for about 90 minutes. Then I loose my hydrostat then the backhoe and front bucket fail to function. Let it sit over night and it's good for another 90 minutes of work. Amy help would be appreciated.

[@dukeman7595]

I believe your clutches are the problem, there is info on "tractorbynet.com" for this problem I do believe.

[@randypack9789]

My loader want go up or down on a tr310 b skeedsteer how do I fix that

[@LRSS2455]

I had a coupler go bad. Everything was plugged in, the check valve wouldn't open. I just had to change the coupler.

[@davidlemieux398]

same problem, but no coupler connections and no leaks. loader won't go up. what do you think.

[@jimbuford4147]

I replaced hose to loader on New Holland tractor and now loader won't lift as high with load as before. Any ideas? thanks

[@MrJerryjam]

I have a Kioti DK35SE 2009 model. My hydraulic system has started to leak down to the point that while carrying a load in the bucket; I have to apply more valve action to keep the bucket up. I have the same issue with the backhoe boom. Is my valve body damaged or is the three-way valve that selects the FEL, Backhoe, or three-point lift at fault. My dealer is about 45 miles from me and his son has taken over the business. His son does not seem to want to give out any information. If I could determine the location of the pressure setting, I would attempt to adjust it after purchasing a pressure gauge. Any thoughts?

[@dukeman7595]

There is info on "tractorbynet.com" for this problem I do believe.

[@FAFO_24]

I've pulled down the round tab and pushed in as hard as I can but the tab will not come back up into position once the hose is seated.

[@MikeSmith-nu9wt]

Kubota has a design that hooks them all at one time , its a junky design that leaks alot and you can't get repair parts for it unless you go through kubota , I ripped it off and threw it in the trash , made a bracket for quick connectors and found the shortest ones I could find

[@Larbear1968]

been there done that.

[@jakeschisler7525]

you know Mike that your tractor and my LS tractor probably came down the same assembly line

[@nickyhobbs2896]

New Holland TL80 when I put travel in forward or reverse it won't move for 1minute or so then it moves why does it hesitant like this?

[@desertracker10]

So I found a guy selling a 1990 7108. He says it doesn’t run. Do you think it would be worth picking up? He doesn’t have specifics on why it doesn’t run. Needs new tires as well

[@dukeman7595]

No. Not unless you can buy it for scrap price.

[@michaelzalewski9417]

I 1982-83 Yanmar 2802D (four-wheel drive). I did just what you said above; cutting firewood & moving brush; pulled one hydraulic couper apart. I cleaned it before re-connecting. Still no hydraulics at the loader nor any 3-point. Change fluid, cleaned hydraulic screen and replaced screw-on hydraulic filter; still nothing. Any help debugging?

[@TractorMike]

Everything was working before and when you pulled a quick connect out everything quit working? That doesn't make any sense to me. If you can e-mail more details to me at [e-mail] I'll try to help you figure it out.

[@theopautsch2311]

another thing to check is if the lines are connected in the right slot if they are backwards it doesn't work either

[@jimexline170]

32 HP tractor with loader. Was liffing a tree on bank. Had bucket in crotch. tree rolled on top of right side of bucket. Pushed the bucket to the ground about 4 feet lifting the left rear off the ground on a twist. Now bucket will curl down if I push joystick very slightly. If I push joystick all the over the bucket curls back up instead of dumping. Bucket stops aabout 5 inches from complete curl up position. Tried back dragging and the bucket just flops. What did I break?

[@Judsonrine]

Tractor Mike that was the problem with the bucket stuck in air but I connected the line back now the bucket curl works but still does not go up or down any more suggestions?

[@TractorMike]

Could the lines be switched? Was the loader off prior to it not working right?

[@Judsonrine]

@@TractorMike I don't think so I believe they are color coded with the caps to cover up when disconnected (the loader) The hydraulic fluid was bone dry but the tilt on the bucket works the raise and lower does not.

[@chrisguidry3367]

What if while you are going up with your loader it changes direction mid stream

[@lindahenderson9400]

You should create a blog to discuss tractor problems I had a neighbor one time they already taken their Ford tractor to the dealership wants because it wouldn't shift gears it was stuck in a in a year I paid the dealership $1,600 a year and a half later the Same problem and all you had to do was told the shift lever out stick a large screwdriver down in line up these three pieces of metal that look like Staples lined up so there's an opening across the center which foot the tractor back in neutral growing up we had a international 454 it got stuck in 4th gear in high range all the time I got so good at pulling this shift lever and lining those things up that I could just sink the clutch with the tractor still running and do it and keep on plowing or bush hogging or whatever manufacturers of filters fluids and parts would advertise on your blog because you're saving the average person thousands of dollars every time they access your site the second time it happened to my neighbor mr. Clarice for tractor I just have to be across the fence on our property he respected my knowledge of farm equipment even though I grown up with his daughter and I am female and I asked you if I could try something he watched what I did his tractor was back up and running in less than 5 minutes he was so Furious that a dealership add charged him $1,600 a year earlier and if I hadn't been working ground across the fence that day the dealership would have got another $1,600 from him thank you very much Mike for your contributions to the Common Man

[@DavidSmith-lp5tz]

My kubota loader slowly lost lifting power. Also when I try to lower the bucket there seems to be a hitch then it lowers quickly. Also the tractor seems to have lost power climbing hills. It’s an HST. I think it’s a hydraulic pressure issue but there are no leaks in the system? Any thoughts on how to problem solve this?

[@TractorMike]

Oh boy. There are a lot of things that could be. When was the last time you changed hydraulic/hydro filters? That's the first thing to check. After that, it could be some kind of internal leak. A technician would probably have to hook up pressure gauges to determine exactly where the issue is. Good luck!

[@DavidSmith-lp5tz]

T Mike. Im going to change out all the fluids in October as well as all filters. I’m hoping that will solve the problem. Honestly it’s been too long between changes.

[@dawrongwitch9036]

Help. My FEL wont lift or tilt up under pressure, but will work if there is nothing in the bucket. Ideas??

[@TractorMike]

The first thing I'd do is change the hydraulic filter. If it's clogged that could be the problem. Make sure all the lines are plugged in all the way. Have you had it off lately or done maintenance to the system? When did it start?

[@dawrongwitch9036]

@@TractorMike it just started. I used it to pull a post out of the ground a week ago and it seemed fine. I dont know how to do much. But I'll check the filter. Thank you for your reply!

[@kimberlyanteau2974]

My loader will go up and down and the bucket will go forward but my husband has turn the bucket all the way forward and now it won’t flip back up how do I fix that

[@jasunaurit2347]

I'll be dang if that didn't work. My lower one looked good, but wasn't seated properly. Thank you!

[@wooten050268]

What happens when the arms of the tractor quit working when the bucket is flat on the ground?- Will not push tires up- Goes up fine and tilt bucket fine, Any help appreciated

[@alanmichaud2076]

hi mike my loader goes up slow everything else works fine just the loader real slow

[@wudgee]

Done this. Still not working. The back hydraulics works but the loader won’t lift. How do I bleed the hydraulics.

[@danielchrist6519]

I have a 640 loader that has completely stopped working. All connectors are seated. Any Idea where to start troubleshooting. I checked the safety switch on the joystick. It is working

[@TractorMike]

Do you feel the hydraulic pump trying to work when the joystick is engaged? If not, it's something broken in the joystick, like a linkage, if it's trying to pump and nothing is happening it could be a clogged hydraulic filter.

[@danielchrist6519]

@@TractorMike it turned out to be a electrical connector on the bottom of the tractor not making contact. Not even close to the valve assembly

[@danielfolk5485]

Have a 8540 Kubota tractor with grapple fork. Having problem with grapple fork not opening . Each time I try opening on joy stick it goes to tipping the bucket instead of opening grapple fork. I believe its a solenoid problem but what am I looking for?

[@TractorMike]

Could be an electrical problem as well. Here's a video that explains a diverter valve, yours may be slightly different: kzbin.info/www/bejne/anq2oZSAfduGn6M. If you're not getting power to the diverter valve, that would cause your problem. It could be a problem with the valve as well.