Hello my friend. This is more than just a video, you put love and passion into it. Great job! New power for your channel. Good luck! 🌹👍
@AndrewThronImprovements2 жыл бұрын
Thank you very much! Appreciate the support!
@thomasbarker21758 ай бұрын
it is not stupid to use screws to start. if you ever have a mess up at least you can take the panel off without trying to dig them out with a cats paw or pry it off with a crow bar. it allows for adjustments.
@christopherdekonstrukt4445 ай бұрын
Need a shed like that to store my motorcycle.👍
@coot8985 Жыл бұрын
Great build! Question about using the Smartside panels horizontally on the front. I'm building a shed now (not as nice as yours) and was wanting to do that on one side. My understanding is that LP says not to do it. Have you noticed any adverse effects? Leaks? Again, love the style of instruction. Subscribed.
@AndrewThronImprovements Жыл бұрын
Hi - appreciate you watching and the subscription! I read that on the installation instructions as well...but no, no adverse side effects so far. I'm sure it has to do with the ability to "wick" moisture - so as long as you have a sufficient overhang, I would think you would be OK.
@atulanandadas Жыл бұрын
The strength of the LP smart siding 4x8 sheets comes from installing them vertically. Also water build up in the grooves could be a big problem if you live in a wet climate.
@adrianred4929 Жыл бұрын
Hey Man, great video ! I am interested of putting this exact build on my backyard. Can you give me a estimate as to how much all this costed ?
@ajdinomanovic40163 ай бұрын
Waterproofing? Will it stay dry?
@michaelshelnutt35346 ай бұрын
Have you done any 12x16 sheds with single slope roof?
@donovan39738 ай бұрын
Is this the usual way to install t111? Do you just caulk the nails, I was thinking it required using staples I'm the seams or something
@jlmc22011 ай бұрын
Should a weather resistant barrier & wrap be used prior to placing T1-11 or LP Smart siding
@LivingConsciously7078 ай бұрын
yes
@Alaska-Bush-Mom2 ай бұрын
I was told that TI-II has no shear strength and cannot be used alone? Has to be installed over OSB?
@patricksmith31352 жыл бұрын
Super video Andrew! You just keep getting better and better with each show. I don't know how you haven't reached 100K yet. Cant wait for the floor treatment; its one in my future plans for my screen porch. Pat
@AndrewThronImprovements2 жыл бұрын
Appreciate it, Patrick! Hopefully soon! The epoxy video should be out soon!
@hhadzios8 ай бұрын
Do you have to fill out nail entrance points w some caulk?
@AndrewThronImprovements8 ай бұрын
Only if they go too deep. If they are flush with the siding, you should just be able to paint them.
@tedjohns3021 Жыл бұрын
No Tyvek?
@relicaro21 Жыл бұрын
how much this you spent building your shed
@joed.20782 жыл бұрын
What CAD software did you use to design and produce the 3D images of the framing?
@AndrewThronImprovements2 жыл бұрын
Hi Joe - I used SketchUp
@joed.20782 жыл бұрын
@@AndrewThronImprovements Any special plug-ins?
@nukestrom57192 жыл бұрын
Are you using 3/8 T1-11 or 5/8 T1-11?
@AndrewThronImprovements2 жыл бұрын
I believe it was the 0.315" LP SmartSide Panels. Thanks for watching!
@djacgators12 ай бұрын
Lost me at window cut out. Sawzall maybe???
@TheUnofficialMaker Жыл бұрын
too bad you didn't have a gable to demo.
@ronlaverdiere Жыл бұрын
Pilot bit in a router makes cutting windows out easy with sheathing in place.
@BGraves10 ай бұрын
Template bit?
@ronlaverdiere10 ай бұрын
Literally the bit is a Pilot bit.
@stringsalive20 Жыл бұрын
For the window - if you’ve got one - it’s easier and even more accurate to just hang the siding. Then, drill a hole, and cutout windows, doors, etc. with a flush-cut router
@Jane-xh6fv Жыл бұрын
Absolutely wonderful instructions! I’m building an 8’x12’ shed right now and our next step is putting the t-1-11’s up. This video is a godsend! Thank you!!
@GoofyFlan2 жыл бұрын
WhOO! Channels like this are why I love KZbin. Contractors will go homeless waiting for me to pay those ridiculous labor charges. ~~Thank You~~
@AndrewThronImprovements2 жыл бұрын
Appreciate it! I learned everything I know from KZbin!
@woodmanmade Жыл бұрын
Nice work! To get some additional water proofing, put some z-flashing above the base PVC trim to divert any water that may make its way between the siding and the trim
@smitaaay9 ай бұрын
This also makes it look very professional. I just put my z-flashing on, yesterday, and it totally changed the way it looks. I know, I know, it's just gonna get covered up, haha, but it still looks good. 🙂👍
@4doormas7586 ай бұрын
I do not like the z channel look on the building. It looks unfinished. Is there anything wrong with just abutting the PVC ledger to the LP?
@woodmanmade6 ай бұрын
if the siding overlaps the foundation then the water can be diverted but siding like this shouldn't be close to the ground as it absorbs water (see install instructions). flashing is the "proper" way but if it's just a shed you could probably get away with house wrap and caulking
@jackktorness Жыл бұрын
If I’m insulating a small outdoor structure like a sauna using this siding, should I have Tyvek over the studs?
@nickbrockelman7 ай бұрын
This is a great question and something I happen to be doing I hope you get an answer
@BR-vp2dz9 ай бұрын
I appreciate that you point out your mistakes. As a new DIYer, it takes some of the pressure off.
@dannyjenkins-pp9se Жыл бұрын
Great place to paint sheets grass grows lawn mower mows painted grass goes!!😂😂
@shidoshikami Жыл бұрын
You used a framing nailer instead of a siding nailer, and it did not split the product?
@ZharsergeyАй бұрын
How is the pvc ledger board handling the black paint? Any issues with it?
@xisotopex9 күн бұрын
dumb question, but would it be possible to install vinyl siding over the t1-11 siding?
@CookieZ33538 ай бұрын
I wished that this was available when I did my shed roof makeover on my well house. I made it up as I went along and fell off of some scaffolding along the way. It's still holding and there's no mold growing due to gaps, so I'm proud. You are speaking waaaaay too fast for some of us older folks. Please don't forget that women like to DIY too and wouldn't it be great if there were a set of tools that were female friendly??? Business ideas anyone?
@rumpstatefiasco2 ай бұрын
You can play the video at different speeds, see the gear shaped icon , upper right of KZbin screen, to select speed.
@davidtaft1180 Жыл бұрын
What's the best way to insulate a shed with smartside panels? Can I attach insulation directly the the panels on the inside?
@atulanandadas Жыл бұрын
If it’s foam insulation you just place it between the studs, fiberglass style is usually nailed between the studs after siding is installed, before the interior finish wall is installed.
@TheAmandaleigh0221Ай бұрын
8:18 Hi Andrew! My mom and I are building your 10x10 shed and bought your plans. We have installed all the smartSide panels and my question is for the front. We followed your directions for the horizontal pieces but the 2x4 top piece seems to not line up well with the top sheathing because of the underlament piece at the top. The top sheathing is not flush with the smartSide panel. Did you cut off that underlament part of the smartSide panel at the top? Thanks Andrew!
@abbondanze4 ай бұрын
Is there a particular type of blade for circular saw you recommend for the Smart Siding panels?
@4doormas7586 ай бұрын
Andrew how is your LP holding out with the ledger PVC under it? Any issues, i want to do the same to my shed. But retrofit after the shed was installed. So to keep the groundhogs from going under.
@proudpennsylvanian3303 ай бұрын
I don't see on any of these videos how you framed in the triangle section on top of the side walls. Am I missing it???
@elsaarauz21889 күн бұрын
Love it❤
@jamescole315221 күн бұрын
concrete.
@asw0210 Жыл бұрын
Don't forget to paint your LP Smart Side cuts! kzbin.info/www/bejne/kH7bqGN5m8qprNU
@melanielong62322 жыл бұрын
Great video! Can’t wait for the rest of the series!! 💙
@AndrewThronImprovements2 жыл бұрын
Thanks! Stay tuned 👍
@amomentwithanimals74296 ай бұрын
What do you fill the nail holes with? Do you caulk the seams?
@hungrybread1722 жыл бұрын
God bless you man, do you have any idea why the outside corners are on flushed, where the 2 sheets connect one of them pops out a bit more than the other.
@stam88 Жыл бұрын
You built something nice, but you destroyed it since you built it on the mud. If you had poured some concrete underneath, it would have been amazing 👏
@smitaaay Жыл бұрын
Literally the second video of this play list shows the concrete slab he has this sitting on. 🤷♂🤷♂
@paulsccna2964Ай бұрын
So. So. And so. So. Good demo. So. None-the-less.
@joseph-ch6gw2 жыл бұрын
I like the horizontal method.. not sure I've ever seen that. Looks sharp, and good idea! I may use that idea
@raidordie94652 жыл бұрын
What state you live in? Just wondering because in California that’s the only way I’ve seen this siding installed.
@joseph-ch6gw2 жыл бұрын
Washington. With the seams horizontal?
@scottvines4093 Жыл бұрын
It's NOT a bad idea to use screws for your first few fasteners in case you're not square and need to make an adjustment.
@kaysylvanus91786 ай бұрын
I totally agree, that's a great idea in case you need to adjust before commiting with nails.
@cf-1 Жыл бұрын
I cannot find information in comments on how to build the shed. Anyone know what I am missing?
@papatutti59 Жыл бұрын
I think he forgot to put it in. I couldn’t find them either.
@evanw6470 Жыл бұрын
Why do you prefer LP smartside ?
@att2976 Жыл бұрын
Are u using frame nails 1.5” nails?
@kidsplay9794 Жыл бұрын
Great video...this best tutorial video i like this
@cf-1 Жыл бұрын
I thought there were downloads
@pineapplepissant Жыл бұрын
High quality content here!!
@MrTexaz101 Жыл бұрын
Do you caulk the bottom of the siding or leave it open so water may get out?
@smitaaay Жыл бұрын
On the LP Smart Siding Website, they say to leave a 3/8" gap between the panel and the trim at the bottom. They also say to put in Z Flashing underneath the panel and over the trim. They specifically say not to caulk or seal any edge with flashing. The Z Flashing with the 3/8" gap will allow the water to drain and will prevent water damage to the siding and the trim.
@JuanTorres-pb7ko10 ай бұрын
Where can I get that door?
@ranniemanangan39865 ай бұрын
Can you install the smart side panel sideways instead?
@TurboMountTV4 ай бұрын
LP Specs say no. Water drainage. They have Lap Siding to have horizontal seems.
@ahmadsoughar4918 Жыл бұрын
Haha the nails vs screws battle 😂
@miguelfuentes4021 Жыл бұрын
What size nails?
@AereForst9 ай бұрын
Beautiful work
@gregjones81352 жыл бұрын
Which program do you use for your cad drawings?
@gregjones81352 жыл бұрын
Nevermind.. just saw the sketch up logo!
@drilon1781 Жыл бұрын
It soo beautiful
@johng80492 жыл бұрын
you should have z flashing were the rim board meets the siding
@KevenDRayne Жыл бұрын
What about if you don’t use a rim board? Just leave open and don’t caulk?
@johng8049 Жыл бұрын
@@KevenDRayne i like to use rim board and no never calk it that will hold the water in. Lot of people use no rim but i had a shop that i resided years ago and after 10yrs the bottom of the LP rotted out . You should be ok as you have a good over hang. Also when you make cuts to LP you should reseal with primer to stop water from wicking. I am just now finishing up a tiny house i might make a video about all the steps.
@andysanchez3030 Жыл бұрын
How thick are the panels?
@irishchewbacca7930 Жыл бұрын
Those panels are usually 3/8" thick.
@lizlo83942 жыл бұрын
It is so beautiful 😻
@AndrewThronImprovements2 жыл бұрын
I appreciate it! Thanks for watching, Liz!
@Salsacandela1532 жыл бұрын
You didn’t put liquid nails bro 😎
@genimarlene2 жыл бұрын
A construção fica direto no chão? Não vai apodrecer quando o chão molhar da chuva?
@AndrewThronImprovements2 жыл бұрын
Hi Geni - it sits on a slab and then has a pressure treated lumber base. Additionally, the roof has an overhang on all sides - so it really doesn't get wet. I hope it lasts 20 years!
@Whitesnakejen2 жыл бұрын
This is the best tutorial on KZbin! Thank you for your good explanations!
@AndrewThronImprovements2 жыл бұрын
I appreciate it! Glad it helped and thanks for watching!
@hebers2355 Жыл бұрын
Thanks Andew, very professional job ,
@AndrewThronImprovements Жыл бұрын
Thanks!!
@steventhorkelsen6478 Жыл бұрын
Would you recommend putting osb and tyvak wrap? Or is that not needed
@AndrewThronImprovements Жыл бұрын
It’s not needed, per se..but it would give you a more robust (and expensive 😬) shed. Good luck building
@steventhorkelsen6478 Жыл бұрын
@@AndrewThronImprovements so here’s my deal, I’m making 22 8’x10’ dog kennels for boarding. So the inside will be insurlwted and finished off . Would you still think I don’t need osb and tyvak?
@PhillyFixed Жыл бұрын
Very helpful series! Just a quick question, have you had any issues with the PVC ledger boards warping? I doubt the black paint is "vinyl safe" and I ignored that once and all of my trim warped in the sun to the point of pulling out 15 gauge trim nails 🫤