Stainless Steel Drip Tray Alteration & Repair

[@JonesMetalCraft]

Nice fix. I like your explanations of what you're doing and why. Thanks!

[@michelastegiano7442]

je suis très fan de votre travaille. Pour le perçage au trépan en ruse il y a de caler la perceuse contre sa jambe, pour ne pas risquer de se blesser le poignet si cela bloque car les perceuses de maintenant on beaucoup de couple. Pour ceux qui ne sont comme vous équipés pour l'inertage, en astuce il y a de mettre sur les envers de l'alu plaqué. I am a big fan of your work. For drilling with a trick bit, you have to hold the drill against your leg, so as not to risk injuring your wrist if it blocks because today's drills have a lot of torque. For those like you who are not equipped for inerting, a tip is to put plated aluminum on the backs.

[@REVERSE_BIAS]

I've not watched for a while...when I left you were MIG all the way! Now you're a TIG master! 😊

[@ARCONEWELDING]

Yeah mate I'm just at the stainless fab shop at the moment

[@sikanderheinsbroek1926]

If you went with a higher sanding grit on you grinder, you wouldn't need to do al those additional steps to make it look acceptable imo. Just go in with a 80 or 120 grit cubitron disk and you would be done, if the customer ask for more at that point. You could use those Scotchbrite pads for the grinder, it saves you alot of time and hassle that way. Still a decent job, that is undeniable, cheers

[@justintasht1067]

Fantastic video and work as always. Great to see a video aswell 👍👍

[@ARCONEWELDING]

Cheers bro

[@gilesfone]

You got it done 👍

[@johnpappas2060]

Bless Good video. Thanks 😊

[@ARCONEWELDING]

Thanks for watching!

[@billywilliams8833]

Hi Why Back purge with Nitrogen Vs Argon ? Thanks.

[@kf8575]

Nitrogen is cheaper

[@ARCONEWELDING]

Nitrogen is way cheaper

[@Carlos-uz1me]

Sou soldador naval no Brasil ,seu canal e de qual país

[@paulusmarc]

Bon Boulo 😆😆👍👍

[@mihasikPOFF]

Сваривать нужно лазером в жёстком кондукторе.

[@tomthompson7400]

I watched right to the point where the screwdriver beating started ,,, then I asked myself , why am I subscribed to this channel , now Im off to un subscribe .

[@petark1933]

Did you know.? They make screwdrivers with steel cap also, so it is not that uncommon to hit screw driver ( ofc steel cap is for different use case ). In the end it does not matter, he is using what he had on hand, because you are probably keyboard warrior from basemen you are not aware that cost cutting is very common today, and in the end it results on you not having right tools on workplace ( he is also using his personal tools... ). Now go back in basement, an be quiet because you have no value to add to this video/topic...

[@tomthompson7400]

@@petark1933 you have no idea about how wrong you are ,,, actually on most of that ,,, your dismissed, now run along.

[@petark1933]

@@tomthompson7400 Ok, I am wrong:) Tell your self whatever you need to sleep better at night, and also to help you with your limp phallus. Cheers ! :)

[@biryaniofbodyhair]

No pickle/passivation after? Also I'd be very wary in future of ever touching the stainless with an old contaminated sanding disc

[@ARCONEWELDING]

Once it's done it's taken out of the Bay and it's down to whoever next to do their part, the fab shop only does stainless so any worn out discs would only be from stainless and oil from the car in solution