Arduino Bluetooth Car using HC05 Master-Slave Transmitter Receiver | DIY 🔥

[@Falcon_X1]

A good project for developing my skill in Arduino... it also helps me to gain knowledge by solving problems. Problems faced (and solutions) 1 - AT mode doesn't open - check the module is HC 05 or 06. the methods are different for both (There are many method to do this.. check it one by one) 2 - Program doesn't upload successfully - check the options in tools section of Arduino before upload (port, board, processor etc...) 3 - modules didn't turn on - check our connections properly (better if use multimeter) 4 - motors doesn't turn properly - change polarity of motors to motor driver by interchanging their wires 5 - motors doesn't work properly - check the voltage and current of battery - it only works in rechargeable battery since it has high current than normal battery if facing problems - use our internet to solve it... we need to face problems for final victory... I hope this helps

[@Falcon_X1]

@hash pin this because it may be helpful for others

[@hashincludeelectronics]

Well done and I am glad that after facing so many hurdles you made it successfully 👏🏻👏🏻👍🏻. And thank you very much for sharing your experience . These findings will definitely help others.

[@Falcon_X1]

@@hashincludeelectronics 😀

[@slyasastech]

True😊❤

[@tamilmovies348]

Bro AT mode is not coming and it is hc05 only

[@Nejtak853]

After all the videoes i have seen on youtube, and after 2 days of very hard working, your video sir, has been the only one that have worked 100% correctly. I dont know how to thank you, i have exam soon, so this video has helped me alot

[@hashincludeelectronics]

Thank you so much for your comments . I am glad this video is helping you 👍🏻👏🏻. All the best for your exam too .please do share the channel among your friends circle as well 🙂

[@chyontech7307]

Some, because of the problem, I will not be online for 2 months, I will not use phone, laptop, I will miss your videos, a lot, but when I come back, I will watch all your videos, eat well, friend.

[@hashincludeelectronics]

Take care 👍🏻

[@fouzanjaved5441]

Love the Arduino Bluetooth Car using the HC05 Master-Slave Transmitter Receiver robot. You should attach the 6-dof robotic arm on the Arduino Bluetooth Car using the HC05 Master-Slave Transmitter Receiver robot to look even more advanced.

[@hashincludeelectronics]

Thank you 👍🏻. I agree. I personally liked this car and it’s easy to handle it with joystick remote control. There is video on my channel of robotic arm car but with esp32 and PS3 controller . Will try to add that arm on this car as well . Stay tuned .

[@fouzanjaved5441]

@@hashincludeelectronics Sir, what courses do you do to get into the robotics field, tell me?

[@hashincludeelectronics]

@@fouzanjaved5441 You can check the tutorials and videos available online about different microcontroller modules like Arduino , esp32, raspberry pi etc. And check how different sensors work. Get some knowledge about different motors working. As far as programming is concerned you need to learn c++ for Arduino. May be check w3schools website. There may be some other courses on robotics available online which I am not aware about right now . But will let you know if I find something more. Learn slowly and regularly, you will be successful 👍🏻

[@irpia7026]

Awesome!

[@hashincludeelectronics]

Thank you very much 👍🏻👏🏻

[@TechnoShuvo360]

Amazing invention... Good luck friend..

[@hashincludeelectronics]

Thank you very much 👍🏻

[@I.C.B_records]

Can we use the hc06 like a slave ? How can i proceed for to pairing hc06 and hc05

[@hashincludeelectronics]

Please try that 👍🏻👏🏻

[@shaikafzal2454]

For getting the address of hc05 use "AT+ADDR?" in the video they have given "AT+ADDR" which give error

[@hashincludeelectronics]

It’s good to always correct the commands 👍🏻👏🏻. Thanks to sharing .

[@야구좋아해요]

Thank you Bro, I also faced with same problem.. haha.

[@AkashDas-vx2ph]

Excellent sir ☺️

[@hashincludeelectronics]

Awesome 👍🏻

[@HACKERANUJ-vk3xb]

BRO PLEASE MAKE A VIDEO ON QUESTION ANSWERING ROBOT USING NANO . THIS WILL IMPROVE YOUR AND ALSO MY KNOWLEDGE. PLEASE BRO. BIG FAN!!

[@hashincludeelectronics]

Nice idea . Will try that 👍🏻👏🏻

[@aaroonikrishna6618]

Hello sir nice video i have one question i dont want to use 7 12 v dc battery can i use li ion battery

[@hashincludeelectronics]

Yes you can 👍🏻👏🏻

[@ChauhanIshanShorts]

Good ideas👍👍👍

[@slyasastech]

How did you learn coding did you followed a course I want to know how to program all alone how should I learn them ❤

[@hashincludeelectronics]

Yes I did learn coding . It’s c++ code . You can learn about basic c++ on internet like w3schools . And then code for Arduino 👍🏻👏🏻

[@adilfarooq1430]

Hi, did you face any delay in receiving signals to the slave hc05 on robot. I am getting delayed signals and at time it jams. What can be the issue?

[@hashincludeelectronics]

Did you change the baud rate by any chance ? Low baud rate will cause this problem . Or you can add some delay of say 50 milliseconds in transmitter code after every transmission.

[@adilfarooq1430]

@@hashincludeelectronics actually i bought a robot with an andriod app as a controller already provided to control via Bluetooth. I can't seem to make changes on the transmitter side. But I can make changes in Arduino code on the receiver side. Can you tell me what I can do, or I can share the code if you can look at it. Pls, send me your email?

[@xenonyoutub]

nice job man

[@hashincludeelectronics]

Thank you! Cheers!

[@FilbertJason]

What key in the keypad are you using to enter message in serial monitor and it is not printing anything "btSerial started at 38400"); this is not printing in serial monitor

[@hashincludeelectronics]

It should be enter . Or you can use the button on laptop screen using mouse click 👍🏻👏🏻

[@FilbertJason]

@@hashincludeelectronics but when we click enter no response

[@Nejtak853]

8:02 to these wires comes with the car package?

[@hashincludeelectronics]

Yes 👍🏻👏🏻

[@Nejtak853]

all the AT-commands work, execpt the "AT+RMAAD" command. i doesnt show a "ok" sign. What should i do?

[@davidjob8917]

Nice project 👍

[@hashincludeelectronics]

Thanks for checking out the video 👍🏻👏🏻

[@ricardogarfias9349]

Hi! Thanks for the video. When the HC-05 module is blinking every two seconds (supposedly indicating that is on AT mode) I enter the "AT" command in the Serial Monitor and I receive OK. The problem appears when I enter the "AT+RMAAD" or any other AT command. I always receive the ERROR:(O) response. What can I do?

[@hashincludeelectronics]

Please check the video for any missing steps 👍🏻👏🏻

[@FilbertJason]

SAME PROBLEM

[@ricardogarfias9349]

@@FilbertJason Please tell me if you figure out how to solve it.

[@arshdixit13]

hi sir what version of Arduino IDE did u use in the video??

[@hashincludeelectronics]

Probably it’s shown in the video . Else I will check and confirm 👍🏻👏🏻

[@haroldo00027]

can I do this project with two Arduino Uno? using HC05(master) and HC06(slave)?

[@hashincludeelectronics]

You can use Arduino Uno in this project . However not sure about HC06 . I would suggest use only HC05 to avoid any issues . 👍🏻👏🏻

[@jakerooni5542]

Hi, I've followed this step by step and the car is functioning properly. I'm wondering on how I can make it go any faster? Yours seems a lot faster than mine, I imagine it's because of the battery that I'm using, what specific battery are you using sir?

[@hashincludeelectronics]

Yes I have used LiPo 3S battery in it which provides around 12V . That’s it why it is faster . 👍🏻👏🏻

[@iamnabha9468]

i didnt understand your circuit in the transmitter device, why did you connect so many pins to breadboard power rail?

[@hashincludeelectronics]

@@iamnabha9468 the circuit is simple . Please check how breadboard works then you will understand everything 👍🏻👏🏻

[@iamnabha9468]

@hashincludeelectronics it doesn’t work for me

[@xpertgamer8431]

Can i use Arduino uno instead of nano in rc car fir hc 05 and motor sheild and joystick with nano...?

[@hashincludeelectronics]

Yes you can use 👍🏻

[@iggyboyTV]

sir it is possible in this setup master and slave control,is control by mobile phone simultaenously?

[@hashincludeelectronics]

I am not exactly sure on this 👍🏻👏🏻

[@sulav_gaming_yt5808]

Can you help me add a potentiometer on the controller that controls 2 servo motor on the car please

[@hashincludeelectronics]

You can check my videos on controlling servo motor and add it in this project . Give it a try 👍🏻👏🏻

[@vedantsharma4089]

Can you please tell the code of same project by using shield motor driver L293D

[@hashincludeelectronics]

This project uses L298N module which is also cheap . I would recommend to use the same module to avoid any issue. However I have not used L293D module ever . So unfortunately I am not sure about it . 👏🏻👍🏻

[@lokeshkumaryadav2254]

Can we do the same with bts7690 motor driver

[@hashincludeelectronics]

Unfortunately I am not sure about this driver 👍🏻👏🏻

[@newlife4965]

Csn i use hc06 for reciver and hc05 for transmitter

[@hashincludeelectronics]

I believe you can. Use HC06 at receiver side only . Give it a try 👍🏻👏🏻

[@ThoughtBytes123]

Please make a video on obstacle avoiding car with solar panel

[@hashincludeelectronics]

@@ThoughtBytes123 there is already video on my channel on obstacle avoiding car . You can easily add solar panel on it . Give it a try 👍🏻👏🏻

[@Falcon_X1]

For all who got error while getting address of Bluetooth module... use this at command "AT+ADDR?" instead of "AT+ADDR" i wish it could help

[@hashincludeelectronics]

Thank you clarification and letting others know . Appreciated 👏🏻👍🏻

[@Falcon_X1]

@@hashincludeelectronics U are welcome

[@justadude5160]

OMG THANK YOU VERY MUCH MINE WAS NOT WORKING THEN IT WORK THX UR THE BEST 😁😁😁

[@Falcon_X1]

@@justadude5160 glad to hear that! keep building new things!

[@ryangerken4251]

I don't have an arduino nano can I juse an arduino uno or is it only possible with arduino nano

[@hashincludeelectronics]

You can use Arduino Uno 👍🏻👏🏻

[@kamieldemeyer]

Would it be able to combine the arduino code from the NRF24L01 with the arduino code of the HC-05? I want to control my RC car with a controller (via the NRF24L01 module). And also be able to control it via an app (with the HC-05 module)

[@hashincludeelectronics]

You can refer my videos for combination.

[@gamesoccer5956]

Sir for both tarnsiver master slave code are same ?

[@hashincludeelectronics]

Please check the video for this step 👍🏻👏🏻

[@AceNexy-Bhargav]

Hi bro! Awesome ved I have a doubt brother I am trying to make a project with Arduino mega which controls car and robotic arm Can I consider this transmitter for my project only to drive the car ??

[@hashincludeelectronics]

Yes you can 👍🏻👏🏻

[@Priyanka-kv6ct]

Hey even I am trying to do that, were you successful at in creating that?

[@AceNexy-Bhargav]

@@Priyanka-kv6ct hey yes it worked I was successful. U just have to make sure that all the connections are proper and it turned out to work well

[@Priyanka-kv6ct]

@@AceNexy-Bhargav oh that’s amazing m, do you mind sending me the wiring and code?

[@AceNexy-Bhargav]

@@Priyanka-kv6ct oh yeah sure where do u want me to send it?

[@omsrivastava6684]

The Serial monitor is not responding when I uploaded the AT configuration code. I tried typing commands like AT, AT+ADDR but no response like Ok from serial monitor. what should I do?

[@hashincludeelectronics]

Please check the baud rate selected . Also take a look at video for any missing step 👏🏻👍🏻

[@FilbertJason]

In the receiver shall we use Arduino uno

[@hashincludeelectronics]

Yes you can 👍🏻👏🏻

[@siddheshwarlondhe5319]

Thank you so much

[@hashincludeelectronics]

No problem 👏🏻

[@AceNexy-Bhargav]

Hi bro ! I hope u rem me but anyway bro how r u?? Bro can u pls say what is the approx range of this config?

[@hashincludeelectronics]

I am good . How are you ? The approx range is standard Bluetooth range around 100 ft 👏🏻👍🏻

[@ashutoshdash1955]

Hello I have a idea can u make a self Balancing bike which drive there are lot of video but none of them explain... So if u could try this out will be a great also it's will be something new thx

[@hashincludeelectronics]

That’s a nice idea . Thanks and Noted 👍🏻

[@Fati-ok5ey]

Hi I have a problem, i did all th steps but my bleutooth slave show only numbers between 245 and 255 i don’t know why

[@hashincludeelectronics]

Please follow the exact step as shown in video 👍🏻👏🏻

[@kevinknight9994]

Anyone know how I can add the code to use 2 analog switches? I know the wiring just dont know how to add the code so it will send signal like the joysticks...

[@hashincludeelectronics]

We are already using 2 joysticks here 👍🏻👏🏻

[@iamnabha9468]

is it possible to use arduino uno for the car?

[@hashincludeelectronics]

Yes you can 👍🏻👏🏻

[@iamnabha9468]

@@hashincludeelectronics how? im not familiar with arduino so how can i configure the arduino uno to work the same as yours

[@neuhold.m]

What should I do if I type AT in my serial monitor and nothing happens, I also get no „atSerial stardet at 38400“

[@neuhold.m]

also my hc05 is blinking red and blue, but if i enable AT mode just like you, both lights blink in a sequence of 2 seconds

[@hashincludeelectronics]

I would suggest to check video slowly and carefully to not miss any step 👍🏻👏🏻

[@neuhold.m]

@@hashincludeelectronics already got it and everything works, great video👍🏽

[@hashincludeelectronics]

@@neuhold.m nice job 👍🏻👏🏻

[@chaitnyasrivastava944]

Sir it's showing error 7 when I put mac address master hc05

[@hashincludeelectronics]

Please check the video slowly and carefully to avoid any issue 👍🏻👏🏻

[@darkangel6559]

Can we connect transmitter to laptop for power instead of batteries?

[@hashincludeelectronics]

Yes you can 👍🏻👏🏻

[@darkangel6559]

Thank You@@hashincludeelectronics

[@hashincludeelectronics]

@@darkangel6559 welcome 🙏

[@tamilmovies348]

Bro i connected every wires and coded. I completed the project and final if i accelerate or decelerate, right or left it is not working dude. Please help me!! 😢😢😢😢

[@hashincludeelectronics]

@@tamilmovies348 please check the connections again . Does your car move forward and reverse properly ?

[@616lizzie]

Nice 👍🏻

[@hashincludeelectronics]

👍🏻👍🏻

[@hellorajamundry]

Bro an emergency please respond please We need a car that can transmitts live video,temperature, gases levels, I would like to use it at Cole mines .... Please please

[@lukaspuhl556]

I just tried everything but my motors are moving uncontrolled all the time and they are changing directions for just a sec also. Do you have a solution for this?

[@hashincludeelectronics]

Use rechargeable battery if not using already 👏🏻👍🏻

[@aayushbhatta9668]

how about i use one uno and one nano?

[@hashincludeelectronics]

Yes it will work 👍🏻👏🏻

[@aayushbhatta9668]

@@hashincludeelectronics i have few questions where can i contact you sir?

[@letantru5106]

can u help me to use double L298N instead of one

[@hashincludeelectronics]

Actually you can check my videos on mecanum wheels car where I have used 2 L298N modules . That will give you idea 👍🏻👏🏻

[@letantru5106]

@@hashincludeelectronics ok guys, i have found the solution with that video, thanks for helping me

[@hashincludeelectronics]

@@letantru5106 awesome 👏🏻

[@NEILMATHEW-e1r]

I am facing a problem. The car moves on its own even when the Joystick is not used. It starts moving after the master and slave are connected. I am using lithium battery of 3.7 volt for the receiver and a power plug of supply 12 volt for the transmitter. Please suggest what is the problem.

[@hashincludeelectronics]

You need to use total 7-12v power supply at receiver . 👏🏻👍🏻

[@NEILMATHEW-e1r]

What I meant was I am using a pair of 3.7 volt lithium battery. Sorry for the mistake

[@anghelleonelretomoreno4966]

I have a similar problem, when the master is connected and the slave starts moving without using the joysticks and I can only control the direction of the car. Does anyone know how this can be fixed?

[@davidoliveira5837]

when i put in the serial monitor the comand AT or AT+RMAAD or AT+ROLE=0 or AT+UART=38400,0,0 or AT+ADDR doesn´t show anything in the serial monitor ("the message: OK")

[@hashincludeelectronics]

Please follow the video 👍🏻👏🏻

[@shahnewajbd4623]

​@@hashincludeelectronics when i type AT+ADDR it's reply me with error,,, what is the problem

[@Fisicracks]

@@shahnewajbd4623 put AT+ADDR? tHE QUESTION MARK is missing, same error

[@dheerajdixit5411]

hi sir i have connected everything correctly the modules seem to connect but then only the master module is blinking and the slave stops blink hence the car does not work can you please help with that??

[@hashincludeelectronics]

I would suggest to take a closer look into video again . This project is very involved and needs lot of attention . Please check video slowly and carefully again. Also make sure you use only rechargeable battery in your project 👍🏻👏🏻

[@Manish_Kumar2022]

Bro when i connect my battery with my l298n motor module my Bluetooth stops working and when i connect the usb my Bluetooth starts working and connects to the master but it's motor is not working

[@hashincludeelectronics]

Which battery do you use ? Use only rechargeable battery because it supplies good current 👍🏻👏🏻

[@Manish_Kumar2022]

@@hashincludeelectronics I used rechargeable battery and it starts working but controller is not functioning and when I connect my battery to vin it Bluetooth stops working

[@tanaysuman8433]

Hi how many arduino nano u used in this arduino bluetooth car

[@hashincludeelectronics]

2 Arduino nano . One at transmitter and another at receiver 👏🏻👍🏻

[@Maharaj568]

Sir software upload nahi ho taha hai 😢😢

[@hashincludeelectronics]

What issue are you facing ?

[@sumitdpatel76]

Can i give power supply of 2200 mah lipo battery ?

[@hashincludeelectronics]

Yes you can 👍🏻

[@storyguyishere]

when i put AT+ADDR its coming error(0) can you help with this

[@storyguyishere]

Can you please help with this error

[@MisterSob]

"AT+ADDR?" try this one

[@AbbasZeynalov-ik2mo]

nice

[@hashincludeelectronics]

Thank you 🙏

[@technicaldilendra5737]

I try to make this project everything is fine but I face problem for steering control this car moving only forward and backward steering not working I try everything wire changing

[@hashincludeelectronics]

Steering is on other joystick.

[@aiwithpaki]

Nice

[@hashincludeelectronics]

Thank you very much 👌🏻👍🏻

[@godgajet6763]

help im sending at but no response

[@aaravakshayshah7527]

I am getting the error"reverse was not declared in this scope can you help me pls

[@hashincludeelectronics]

Please check video and code properly for any missing step 👍🏻

[@slyasastech]

How about the transmit range

[@hashincludeelectronics]

It’s a classic Bluetooth communication which has range around 100 ft or so . 👍🏻👏🏻

[@himanshu015-x8v]

i used 2 motors for speed and 2 motors for steering can u provide code for that please

[@hashincludeelectronics]

It’s not just providing code but it needs testing as well. I would suggest to take help of the existing code and make changes accordingly 👍🏻👏🏻

[@TECHAB254]

Can bluetooth module be used again

[@hashincludeelectronics]

This project uses Bluetooth module only .

[@godgajet6763]

do this code work on UNO3 ?

[@hashincludeelectronics]

Yes it works with Uno as well 👍🏻

[@shahnewajbd4623]

After try for it ,i can't use the hc05 module for other projects

[@hashincludeelectronics]

You need to set the addresses and modes properly 👍🏻👏🏻

[@shahnewajbd4623]

@@hashincludeelectronics please help me to make my hc05 useable with mobile phone

[@SumanDevi-wq8hh]

Bro its showing error(7) while at+bind

[@hoblau317]

why must be rechargeable battery ?

[@hashincludeelectronics]

Rechargeable batteries provide good current and these have good capacity . Also these last longer . It solves many power related issues 👏🏻👍🏻

[@LarsDeRuntz]

Maybe this could be a self driving car too.

[@hashincludeelectronics]

👏🏻👏🏻

[@shlokdaga]

What is its range to control?

[@hashincludeelectronics]

I tested for 60-80 ft

[@storyguyishere]

Bro how to anti bind the bluetooth

[@storyguyishere]

I want to unpair the both slave and master

[@hashincludeelectronics]

Please check for this step on internet 👍🏻👏🏻.

[@tsgaming1v6]

4:39

[@ashikfahmin2776]

how can i made this car with bts7960 module

[@hashincludeelectronics]

Unfortunately I am not familiar with this module so not able to comment . Please check some references.

[@ashikfahmin2776]

Ok... i will

[@iamnabha9468]

when i try to do AT commands it says error: (0)

[@hashincludeelectronics]

Is this issue resolved ? 👍🏻👏🏻

[@delamercedjullianneapples.625]

is the code is plug in play?

[@hashincludeelectronics]

Yes. However you need to do some setup like master slave configuration for Bluetooth modules . For that you will have to perform some additional steps shown in video . 👍🏻👏🏻. You can check my other Bluetooth car video where we don’t need such master slave additional set up 👍🏻

[@krishiprojuktitheindiangar9562]

My problem is solve thanks for reply 🥰

[@hashincludeelectronics]

Awesome . Nice work 👍🏻👏🏻

[@newlife4965]

Did u make it and work good plz tell me any problems happen or not

[@tamilmovies348]

Compilation error is coming for transmitter if we upload the code

[@hashincludeelectronics]

Please send me exact error here 👍🏻👏🏻

[@tamilmovies348]

How to send bro

[@hashincludeelectronics]

@@tamilmovies348 copy paste error here

[@tamilmovies348]

​@@hashincludeelectronics how to send bro

[@tamilmovies348]

Bro please send your mobile number bro

[@zofmod]

U could use a ps3 or ps4 pad for your car aswell btw

[@hashincludeelectronics]

Yup . I have used those as well . Check my other videos related to ps3 and ps4 controller cars .

[@zofmod]

@@hashincludeelectronics i was just looking lol nice videos bro

[@hashincludeelectronics]

@@zofmod awesome

[@zofmod]

@@hashincludeelectronics im doing home assistant with my stuff here's a old video kzbin.info/www/bejne/lYOtmaGIqdOGY5o

[@Nejtak853]

AT+RMAAD does not work. no "ok" i showing up

[@hashincludeelectronics]

Were you able to connect ?

[@Nejtak853]

@@hashincludeelectronics I just skipped this step, and it worked

[@hashincludeelectronics]

@@Nejtak853 awesome 🙌🏻

[@aurobindo1231]

Make temp and humidity sensor with bluetooth and android app

[@hashincludeelectronics]

Sure. Will try.

[@aurobindo1231]

@@hashincludeelectronics thanks

[@vijaykarki5143]

Sir our project not work i am done all things

[@hashincludeelectronics]

Please check connections again . Check video again slowly and carefully for any missing step . Use rechargeable battery to avoid power related issues 👍🏻👏🏻

[@TECHAB254]

Error showing on AT+ADDR on serial monitor

[@hashincludeelectronics]

Thanks for checking the video 👍🏻 could you please share more details on this error ? Or send me screenshots of error on Instagram hashincludeelectronics

[@TECHAB254]

@@hashincludeelectronics solved

[@hashincludeelectronics]

@@TECHAB254 awesome 👏🏻

[@TECHAB254]

@@hashincludeelectronics but car was not working

[@hashincludeelectronics]

@@TECHAB254 keep trying. Use only rechargeable battery .

[@TKherithEquwan]

Can you send the coding arduino?

[@hashincludeelectronics]

Code and diagram link is provided in the description of the video 👍🏻

[@FilbertJason]

Bro all done but at final it is not pairing and not working

[@hashincludeelectronics]

You can check your connection diagram and make sure both of the modules are in the correct mode. 👍🏻👏🏻

[@krishiprojuktitheindiangar9562]

Diagram is not open please provide diagram

[@hashincludeelectronics]

I just checked and it’s opening fine . Please check 👏🏻👍🏻

[@krishiprojuktitheindiangar9562]

Please believe me diagram download is not done

[@zofmod]

You can connect multiple HC-05s with kzbin.info/www/bejne/n36onmaHp7VmbbM

[@istiyekahmedshayem7721]

ভাই আমারে এটা বানাইয়া দিবেন

[@baburaoamzire1730]

code upload nahin ho raha hai

[@hashincludeelectronics]

Please check the video for details 👍🏻👏🏻

[@sifurrahman1740]

❤

[@arhamjain3782]

Ok isnt coming while typing AT

[@hashincludeelectronics]

Please follow the exact steps shown in video . Check video slowly and carefully for any missing steps 👍🏻👍🏻

[@letantru5106]

i have a problem, when my car just started, it runs normally but after that i can't controller, i press reset button on arduino board and it back to normal how can i fix that

[@hashincludeelectronics]

Is the issue resolved ?