Are HM 0702 32,5000's an Upgrade on the Air65 Champion? -

[@mtyler2469]

Band does help prepare you for life! Sounds wrong but the teamwork and ability to adjust on the fly really helps, plus everyone involved already have something in common.

[@apachesmokewoundedsniper]

04:12:2024 What’s up Ciotti and all you GG. 00:03:33 On this stream……. 00:13:05 Please keep supporting this channel. 00:14:45 Lesson learned. 00:19:17 Gemfan has a 35mm S in tri and biblade now. 00:23:30 Have you seen the new Matrix AIO? 00:26:06 Did my 6 packs. I flew my Walksnail 75mm around the room. 00:32:57 I just bricked the 1 esc. 00:34:42 How does a 2 inch Cinewhoop pusher compare to motors up? 00:43:10 Coole thumbnails. 00:44:30 Have you seen the new BNF HappyModel 7HD? 00:50:20 Drive instructor Drone instructor and dance instructor. 00:54:26 My flight controller has a build in spi receiver, could not bind it to my radio. 00:57:36 Looking at a light weight 3 inch build. 01:02:36 I think there are plenty of people who do 6 packs a day. 01:03:22 Did you got the Cinesplore V2 up? 01:08:45 A good livestream idea would be the new Matrix AIO vs the 2G4. 01:10:34 Who is that Johsua person? 01:13:11 Have you seen the GPRC 1002 25,000kv. 01:17:14 O3 uses 2.4 for binding to the controller, and 5.8 is for video. 01:18:15 Pretty sure mismatching linear and cp encores a 3Db drop. 01:21:22 What happened to the 2s Vision 40? 01:22:28 Analog 2s 75build. What is in the build. 01:24:18 DJI is typically left hand circular polarized. 01:27:06 That tiny whoop antenna is linear. 01:29:42 I see that little whoop stand there. 01:30:18 What 4 in 1 AIO would you recommend for 75mm hd build? 01:31:15 Let’s fly and switch motors. 01:32:07 But first it’s Teddy Spaghetti time. 01:34:22 For real now, let’s fly. 01:42:30 Moving over to the biblade. 01:45:55 Something is going on, let’s check it. 01:50:49 Still something is weird. 01:55:03 Will it fly better now? Stay safe everyone and have fun flying.

[@le_tranq]

Spat out my coffee when you realised motors were direct soldered 🤣.

[@Uriel767]

preach bro..

[@Dawe957]

Best source for whoop whoop infos🎉🎉🎉

[@Tokyo_Dom]

When I've had motors that I don't want to cut the plugs off (for resale or whatever), I just desolder the motor wires from the motor base, and then make 12x short tinned awg 30 wires and put those onto the motors instead. Makes it really easy to just solder the motor plug wires back on if I want to go back. This obviously only works with motors that have pcbs on them. But it only takes 30 minutes

[@Dawe957]

KZbin Tutorial incoming ?

[@Dawe957]

Do you mean enamelled wire?

[@Tokyo_Dom]

@Dawe957 enamel wire is one option, but I mostly just use silicone wire, 2mm stripped and then tinned with solder

[@Dawe957]

​@@Tokyo_DomWithout insulation?

[@Tokyo_Dom]

@@Dawe957 of course with insulation? Why would you take it off unless you wanted to see sparks and fireworks?

[@le_tranq]

Changing 03 antenna really doesn't make much difference (unless you are doing some huge long range antenna). You can change the top antenna on the G2 easily but all other models aren't plug and play. Lots of people say the best performance they get from 03 is actually changing the single antenna on the 03 unit to two linear whip antenna.

[@himox1651]

Hello Mr. Ciotti, It was late for me and I fell asleep. However, while I was flashing BluJay on my Air 65, the battery died mid-flashing, and I disconnected the USB port; I plugged in a fully charged battery then the 1 ESC isn't showing up in the ESC Configurator anymore. I have reached out to Betafpv and am waiting for their response. -I will update this comment later if I manage to unbrick it. Quick tip: If u want to flash BluJay please make sure to use a FULLY CHARGED battery and a good USB-C cable. Also, ensure your RC is TURNED OFF.

[@jiatan_fpv]

Hope they sort you out; if not, it's pretty hairy but you can reflash them manually using an Arduino

[@himox1651]

@@jiatan_fpv I hope so, that is my plan, iIjust need to locate the PINS to connect to the Arduino. :(, I have never done this before, but here we are, we learn something new every day. What a great Hobby.

[@himox1651]

@@jiatan_fpv thansk man, i hope so, i have an arduino uno and my plan is to flash it using C2 Interface, unless they send me a new board lol.

[@BreeZieDoesiT]

Hi Ciotti. I have a brand new hdzero lux cam mob 6. Is it worth soldering my 34K motors to it, using peek screws, and swapping the frame out for a Lite AF frame to get me at around 18.2g rather than the stock 19.7g. I have experience but was curious if you think I should go ahead with it

[@CiottiFPV]

@@BreeZieDoesiT I’m very against direct soldering motors and the plastic screws but the lite af frame is great

[@WayneHunter1000]

where do i get HM 0702 32,5000's

[@CiottiFPV]

@@WayneHunter1000 WeBleedFPV

[@memeuridedimineata]

that's how streams end now eh? lol

[@CiottiFPV]

@@memeuridedimineata getting really annoyed by how shitty all this software is becoming

[@memeuridedimineata]

@@CiottiFPV yeah, i've heard your struggles... basically duk cannon and every company that makes u use a propitiatory software