Are You Cross Cutting With Confidence ?

[@warrensmith2902]

SMUTS!!! love it. Very confident. I use a MDF triangle from a good 2' x 2' piece to set up my table before cutting, and a set of story sticks to set up my flip stops before cutting anything. Once my side panels are cut, I check them against a temple I keep with all my 32mm setups on it. Finally, when cutting my bottoms, I use the that spacing to cut 5 stretchers the same width. Now assembly is simple.

[@sedgetool]

Great tip!

[@joebeaton1101]

Outstanding info!! If you spend the time to set-up properly, job goes SO much easier!!

[@sedgetool]

Thanks Joe ...

[@myk1200s]

The Right tools make the difference........ Great presentation sedge 😁

[@sedgetool]

Yeah Baby !!!...Thanks !!

[@spilleradam]

I like your videos, the Festool track saws are good, especially the new ts 60 but there are a few things I like about the mafell mt55 it has a scoring function, it has longer tracks 1.6 meters, and they connect easier with one wide connector on top, and the rubber splitter gaud slides in instead of sticking on.

[@sedgetool]

ok

[@michelmerinis2890]

Thank you for your advices !

[@sedgetool]

Glad you like them!

[@thepaintprofessor]

That action shot panning up off the table saw with the push stick was awesome!

[@sedgetool]

Thanks !!!!

[@nullstyle]

Not only was that wicked sharp, it was was fairly close to _wutang_ sharp. Thanks for the lesson!

[@sedgetool]

You bet!

[@marcosbatista6227]

Obrigado por mais essa aula de altíssima qualidade mestre Sedge, esses equipamentos festool são maravilhosos ❤

[@sedgetool]

Gracias !!!!

[@marcosbatista6227]

@@sedgetool gracias!!!

[@michaelnorman5640]

Love the thumbnail sedge! lol regardless great tips as always!

[@sedgetool]

Glad you liked it!!

[@AngieWilliamsDesigns]

My MFT table was one of the tools in my shop that I was so happy to buy. Before it came in I remember thinking... "am I going to regret this... it's just a table". My only regret was not getting it sooner. I wish I had two more. LOL>

[@sedgetool]

wicked cool !!

[@billhilson8320]

Wicked Sharp!

[@sedgetool]

Wicked !!!

[@balenabros3246]

Sedge any sys containers for the router plexi jig?

[@sedgetool]

not that I am aware of

[@myk1200s]

Sedge what folding ruler do you use festool ❓

[@sedgetool]

Hutafors

[@newera3757]

Where did you get those T-track hooks located behind you on the wall for holding triangles and the rest?

[@sedgetool]

the tarcks are justed scraped rails and the hooks are for square pegboard and a variety of t-nuts...

[@davem4256]

Interesting thumbnail pose, you remind me of George Costanza posing on the couch, please keep your pants on! LOL

[@sedgetool]

Bingo !!!!!

[@Tylerbb8122]

Is the top replaceable later down the road when it’s got a million cut marks?

[@sedgetool]

Yes !!!

[@milandjordjevic5949]

Great Video Sedge , but where is Big D ? Thumbs up 👍

[@sedgetool]

He took some time off ....

[@atomictyler]

couldn't you use your TSO TDS-13 to set the measurement for repeatability? I've been surprised at how well they hold a position once they're locked down.

[@sedgetool]

I should try that !!

[@spilleradam]

The Festool track saw, has more accuracy’s available then mafell.

[@sedgetool]

ok

[@adamspiller4842]

The Festool isn’t more accurate, they are both very accurate saws.

[@billF2380]

And how much does that system cost? My guess…well over 1K

[@sedgetool]

roughly

[@MattLitkeRacing]

Waiting for the know it all’s to say the factory edge is cut better than you can lol

[@sedgetool]

Me Too...... 🤣