Area Ratio, Inside Clearance, Outside Clearance, Recovery Ratio

For full course visit our website
www.machenlink.com/course/fou...
The sample disturbance depends upon the design of the samplers and the method of sampling.
The design features governing the degree of disturbance are
Cutting edge,
Inside wall friction,
Non - return valve.
Area Ratio
The degree of disturbance of the sample collected by various methods can be expressed be a term called the area ratio,
The penetration resistance of the sampler,
The possibility of entrance of excess soil
Danger of disturbance of sample
The allowable area ratio intended for obtaining undisturbed samples depends on
diameter,
design
method of operation of the sampler.
The area ratio should be preferably be less than 10 %.
The greater area ratio can be tolerated when the sampler is provided with
A stationary piston
The cutting edge having very small angle of taper (𝜽).
Inside clearance
The soil is under great stress as it enters the sampler and has a tendency to laterally expand.
The inside clearance should be large enough to allow a part of lateral expansion to take place
It should not be so large that it permits excessive deformations and causes disturbances of the sample.
For good sampling process
Outside clearance
For good sampling process, the ratio should be within 0 - 2 %.
Guide lines for good Sampling
Minimum inside diameter = 𝑫_𝒊=75𝑚𝑚.
The length (𝐿) should be at least equal to (𝑡ℎ𝑒 𝑖𝑛𝑡𝑒𝑛𝑑𝑒𝑑 𝑙𝑒𝑛𝑔𝑡ℎ+100𝑚𝑚) for residual soils.
For soft soils depending upon the sensitivity, (𝑳/𝑫_𝒊 ) ratios are given in table
The cutting edge angle should be within 20°.
The tube should be uniform and should not have any bump or irregularities.
The inside of the tube should be clean and smooth.
Recovery Ratio
It represents the disturbance of the soil sample.
For good sampling the recovery ratio should be 96 to 98 %.
Wall friction can be reduced by suitable inside clearance, smooth finish and oiling.
The non - returned wall should have large orifice to allow air and water to escape.
For full course visit our website :
www.machenlink.com/course/soi...
For full course visit our website
www.machenlink.com/course/fou...
Follow #MachenLink
Facebook: / machenlink
Linkedin: / machenlink
Twitter: / machenlink

[@sanketlawhale8707]

Sir ,your lectures are very helpful for us 😇 Sir plz make video's on further topic's of foundation engineering

[@souravmishra6365]

Sir!!! Very nice Understanding👌👌

[@jigukhetani]

Bahut badiya video banaya hai sir

[@malikmohammadmuneeb7481]

Sir u r bueaty...nice way of teaching

[@sadhnamishra5982]

Thanks 🙂 sir

[@owaisfayyaz4115]

good sir

[@believer1201]

thankyou sir..it was helpful..aage ke lectures type of sampler..type of borings..wo nahi hai sir ?????

[@souravmishra6365]

Sir!!! please Convey the trick to Remember The Bossenesq's Equation & Westergard's equation of stress distribuitions of soils?

[@souravmishra6365]

Sir!!! Which one will be called Expansive Soil ? Where Lr < 1 Or Lr > 1 ?

[@RamKumar-ec5kq]

There should be diameter of cutting edge not sampling tube please correct that

[@manishpurbey3948]

Next video Ka link

[@ramyap9330]

Good but writing are not clear

[@RamKumar-ec5kq]

Numerical statement is wrong

[@sasi74]

English please