How to change "HUBS bearing" .front and rear. Easy and simple. For arrma kraton,talion,outcastls
Пікірлер: 34
@RCRoads10 ай бұрын
Thanks for sharing these repairs. Very helpful and I have to say the car stand your using looks quite stout. Great job..
@g.bjumpsbashing30628 ай бұрын
Thanks
@voldano-012 ай бұрын
L78.. Great sharing
@g.bjumpsbashing30622 ай бұрын
Thanks bro
@burn1gotbeats Жыл бұрын
I enjoy wrenching on my cars I like the smooth music too 😎
@g.bjumpsbashing3062 Жыл бұрын
thanks mate
@TheflyingkiwiRC2 жыл бұрын
I am doing this now first the first time in my Typhon 6s after doing a front wheel bearing this morning. Thanks so much for your video bro ... big help. 💪👍
@g.bjumpsbashing30622 жыл бұрын
Thanks alot champ....hope its help. Enjoy mate
@Kakatouring Жыл бұрын
what a big rc, i think a kid could ride it
@g.bjumpsbashing3062 Жыл бұрын
thanks alot champ
@G9RCCar8 ай бұрын
Nice work, buddy
@g.bjumpsbashing30628 ай бұрын
Thanks mate
@Bensonsan2 жыл бұрын
Nice now I know what just happened to my typhon 6s. Thanks
@g.bjumpsbashing30622 жыл бұрын
Great champ Thanks...goos luck Tide little bit the drop screw...
@Fre2dy2 жыл бұрын
Thank you
@g.bjumpsbashing30622 жыл бұрын
Thanks bro
@G9RCCar3 жыл бұрын
So creative
@g.bjumpsbashing30623 жыл бұрын
Thanks bro👑
@jfnunn17782 жыл бұрын
Do they put the arong set screw in the manual or is it just me? 5x5mm set screw but its too small
@g.bjumpsbashing30622 жыл бұрын
Thanks for coment champ. The long screw..? Wich time is it on the vid?
@jfnunn17782 жыл бұрын
@@g.bjumpsbashing3062 1:43 that screw
@g.bjumpsbashing30622 жыл бұрын
@@jfnunn1778 yes bro its...5*5mm This is the original size. You pull him out?
@jfnunn17782 жыл бұрын
@@g.bjumpsbashing3062 yes im doing a whole rebuild on the rears the same size set screw is too small for that axle if it helps i got a 2019 v4 or later i think
@dolanbarengofficial97882 жыл бұрын
Salam kenal dari Indonesia
@g.bjumpsbashing30622 жыл бұрын
Thank you
@FLSharkdiver3 жыл бұрын
@min 5:36 i am having issues getting my CVD Drive shaft back in since the pin came out!!!Any thoughts??
@g.bjumpsbashing30623 жыл бұрын
Hey bro...sory...im not undersdend..if you can send me a few photo...i wil see..thanks. Bitong1@walla.com
@FLSharkdiver3 жыл бұрын
@@g.bjumpsbashing3062 SENT
@g.bjumpsbashing30623 жыл бұрын
@Old Soul you can put "dif shim" 13*16*0.1 between the "red hex hub" and the plastic black hub